Subscribe to AfterDawn's weekly newsletter.
still rrod after heat gun fix
#1
09 Jun 2011 @ 21:13
glh290
Send private message to this user
Newbie
i did the heat gun exactly as done in the video provided to me in my last post
by exactly i mean i got the same gun and did everything as the person in the video did exact timing everything
and i get the error 0103 again after the heat gun fix if there is any better instructions/suggestions i would be grateful
by exactly i mean i got the same gun and did everything as the person in the video did exact timing everything
and i get the error 0103 again after the heat gun fix if there is any better instructions/suggestions i would be grateful
This message has been edited since its posting. Latest edit was made on 09 Jun 2011 @ 22:12
AfterDawn
Advertisement
#2
09 Jun 2011 @ 22:05
i should also say i found my ram chip pads and used them when i started the xbox and also waited 45 mins to let it cool
#3
09 Jun 2011 @ 22:50
I would try again...this time, try flushing the motherboard with acetone (mainly under the chips) and use a toothbrush to VERY gently brush away any dust/debris from the surface of the board while flushing. Your error code suggests to me that you should concentrate your heat on the ANA/HANA chip and the GPU.
Using Kester No-Clean liquid flux (or similar no-clean flux) under the three main chips is always a good idea as long as you don't use too much and don't heat too long. The flux removes oxide buildup and basically rejuvenates brittle solder.
I use these methods to fix 0102/0103, E74, etc and have had a great success rate bringing back hundreds of consoles. I Hope it helps you to save yours.
Using Kester No-Clean liquid flux (or similar no-clean flux) under the three main chips is always a good idea as long as you don't use too much and don't heat too long. The flux removes oxide buildup and basically rejuvenates brittle solder.
I use these methods to fix 0102/0103, E74, etc and have had a great success rate bringing back hundreds of consoles. I Hope it helps you to save yours.
"All drives should be updated to Lite Touch + (LT+) firmware if playing on XBOX live. Samsung drives and pre-78/79 Hitachi drives do not utilize AP 2.5. All other drives are considered to be detectable by Microsoft (YMMV). Make sure all rips are ABGX verified, contain SSv2, and patched AP2.5 (where needed). XGD3 must currently be burned on new drive with PC Burner Max firmware for 100% rip. All modded consoles can be potentially unsafe for use on XBOX live."
#5
09 Jun 2011 @ 23:55
"All drives should be updated to Lite Touch + (LT+) firmware if playing on XBOX live. Samsung drives and pre-78/79 Hitachi drives do not utilize AP 2.5. All other drives are considered to be detectable by Microsoft (YMMV). Make sure all rips are ABGX verified, contain SSv2, and patched AP2.5 (where needed). XGD3 must currently be burned on new drive with PC Burner Max firmware for 100% rip. All modded consoles can be potentially unsafe for use on XBOX live."
#6
09 Jun 2011 @ 23:59
thanks ill try it now also i have no flux or acitone and i cant go out and get it b/c its 12:00
edit dint work there is still error 0103
edit dint work there is still error 0103
This message has been edited since its posting. Latest edit was made on 10 Jun 2011 @ 9:45
This discussion thread has been automatically closed, as it hasn't received any new posts during the last 180 days. This means that you can't post replies or new questions to this discussion thread.
If you have something to add to this topic, use this page to post your question or comments to a new discussion thread.
If you have something to add to this topic, use this page to post your question or comments to a new discussion thread.
