|
question on coolsat 5000
|
|
|
almeida08
Newbie
|
3. August 2007 @ 18:39 |
Link to this message
|
Hey I'm looking for the bin file for cool sat 5000 platinum
|
|
Advertisement
|
 |
|
|
|
coldwell
Junior Member
|
3. August 2007 @ 18:44 |
Link to this message
|
Originally posted by Bond07:
guys plzzzzzzzzz....where do i get bin 145 for Coolsat 5000??????
I have to change code like every 30 minutes and I have bin 140....plzz someone where would I be able to get bin 145?????
There is a link on page 114 in this forum under Jerry post.
|
Junior Member
|
3. August 2007 @ 18:46 |
Link to this message
|
Originally posted by Bond07:
guys plzzzzzzzzz....where do i get bin 145 for Coolsat 5000??????
I have to change code like every 30 minutes and I have bin 140....plzz someone where would I be able to get bin 145?????
if u want to get new bin file, just e mail me at cali_cali123@yahoo.com.. i will send to u....
|
|
bad_boy69
Newbie
|
3. August 2007 @ 18:48 |
Link to this message
|
|
anybody with loader for 6000 platinum??? please or where can i get it?? thanks
badboy
|
|
MESMD
Member
|
3. August 2007 @ 18:51 |
Link to this message
|
Originally posted by mantis17:
Originally posted by MESMD:
Originally posted by hulio38:
Originally posted by mantis17:
Dish Network 0101
YOUR NEW KEYS HAVE BEEN UPDATED BY THE 8-3-07 ONES!!
NO NEED TO CHANGE IF YOUR AUTO ROLL WORKS. JUST CHECK CH 8282 AND YOU WILL SEE THE NEW ONES IN PLACE!!
Last Updated: 2007/08/02 5:18 PM PDT
86: D9 E3 98 5A CC 2D AC 6E D2 46 8D 0F FC D1 2B 8F
96: D6 50 4C 5D 34 A7 38 DE 45 B5 13 FD 27 C5 88 08
Bell Logo
Bell ExpressVu 0901 awesome... thx up and running again
Last Updated: 2007/08/02 4:49 AM PDT
86: 17 62 8C D3 8C 15 A2 70 CD 9E 87 4F D4 9E A6 3E 0A
96: 79 D1 F2 EC 76 60 52 5C E5 24 E1 97 8B BC EC 26
your post doesn't make any sense, those keys are old and from yesterday, if you have autoroll working, you don't have to worry about it.
THE KEYS HAVE CHANGED AGAIN AND IF YOUR AUTO ROLL IS WORKING THE NEW KEYS WILL BE AUTOMATICALLY INSERTED FOR YOU. THAT IS WHAT AUTO ROLL DOES!! YOU CAN ALWAYS CHECK THE LATEST KEYS AGAIST CHANNEL 8282 WHERE YOU CAN SEE THE CURRENT KEYS THAT ORE ON TOUR RECEIVER. IF THET ARE COBBECT, THE AUTO ROLL IS WORKING!!!
|
AfterDawn Addict
|
3. August 2007 @ 18:52 |
Link to this message
|
I want to thank everyone thats helping out with all the good information when I'm not on this forum. Good job .
I'm going to repost the Coolsat setup guide below from page 27 so some of you don't have to go back that far to read it.
Also, those of you trying to get BEV channels---you can't just scan for them. You need lnbs aimed at the BEV sats to get those channels. DishNet and BEV are 2 different systems with the most common setup being 2 sats for each provider.
------------------------------------------------------------------------
All Coolsat files and loaders can be found at this site below.
http://www.f2atv.com.
This setup guide was posted already, but I will post it again.
Here is the Coolsat 5000 setup instructions.
--------------------------------------------------------------------------------------
How-to-setup a CS 5000 Platinum . . .
The following is a detailed explanation of the required steps to successfully setup NEW CS 5k Platinum. You can also use this to setup any pre-configured CS 5K.
Since it fresh-from-the-box only a few steps are needed. You need to have the STB connected to a dish that has been ‘boresighted’ (aimed) to the satellite in question. Also it may need to have a diseqc switch in the path to the STB depending on the LNB. Or . . you could have a DP LNB that doesn’t require an intervening switch.
Cable Connections:
Strictly speaking if you have JUST put a new system up and it's never been 'de-bugged', then it WOULD be wise to NOT connect the coax line from the dish. If the coax is shorted, it would prevent the CS from booting properly and it would just 'shut-off', possibly doing some damage. At this point, you do NOT need any cable connections but I prefer that you have a video lead to the TV so that you can see a "menu" when the time is right.
Conversely, if your DISH/LNB/COAX setup has been working properly and you are installing a new rcvr, then there's no reason NOT to make all of the needed connections to the CS. That shouldn't present a problem.
Some instructions say . . . "don't connect any cables other than the RS-232 modem cable" are meant for my first scenario re the "new Dish/LNB/Coax" and are there to prevent a premature disaster.
So first make sure that the CS RS-232 connector is connected to a computer using standard Modem cable. It will NOT work with a Null cable!
The following procedure assumes that you know "something" about setting up a FTA rcvr.
1) Turn the power switch on the BACK of the STB to “ON”. Using the remote, press the "POWER" button, it should boot up.
2) Click on the current version of the Pro Loader (in the Download section) and click start the program. Please note that all files are "zipped" and reguire you to "unzip" them. You can NOT load the files directly as downloaded.
3) The opening screen appears; select “Software” and make sure “ToReceiver” is checked. Press the “BROWSE” button and select the flash to be downloaded. At the time of this writing, the current flash was NorW version “123”. Please note that all flash files are "zipped" and reguire you to "unzip" them. You can NOT load the files directly as downloaded. You will need WinZIP or an equivalent program.
Make sure that you select the most current version at this point.
4) Click “Connect” and a dialog box will open. If all is OK, the box will say “Version 1.0 detected”. If the STB is NEW, then that’s what will be displayed. If it is NOT NEW, then the current flash will be displayed.
5) Click “Start” and the download will begin. It takes about 1 – 2 minutes to complete. DO NOT INTERRUPT this process. When complete, the STB will display END in the display and then reboot.
6) You have now flashed the receiver with latest operating sw. Next you will need to configure your dish setup.
First, and this is important, you need to (re)SET the STB to recognize the current flash. If you do NOT do this, all of the satellites will NOT appear in the satellite menu.
1) Press “MENU”, select “System Setting”, press “OK” and select “Database Reset”.
2) Enter PIN, “0000” and scroll to select “Delete All Channels”. Press “OK” and all channels will be deleted. For a BRAND NEW STB, there will be no channels but it does not HURT to do this. All channels will be deleted if there are any channels.
3) Next select “Factory Set”, press “OK” and the current loaded flash will be installed.
Any time you load a "flash", you should always use do a "F-S" AFTER you load the flash.
Configuring the OPTIONS Menu;
1) Press the MENU button and select “Installation”, then enter PIN (“0000”), next select “OPTIONS”.
2) Make sure the following are checked;
Use default CH name ---------------- ON
Renumbering by SID ----------------- ON
Sort by SID ------------------------- ON
Sort by SID after Scan -------------- OFF <-- change allows channels to sort by "TP"
Beep on scan the signal ------------- OFF
Unlock lock CH after PIN ------------- OFF
Renumber BEV ----------------------- ON <---This adds 1000 to the SID of each BEV channel.
Auto CH/TP Update ------------------ OFF <--- does not find channels that change satellite, only if they changed TP, so leave it OFF
The STB is now setup to be configured for the dish and LNBs being used.
1) On the TV screen, a multi-language display will be shown; select “English”.
2) Press the “MENU” button; select “Installation” by pressing “OK”. A dialog box “Enter PIN” shows; enter “0000”.
3) Under “Dish Setting” menu, select the satellite to be setup. For this example, we will use “110.0W Echostar 6,8”.
The proper combos for a LEGACY LNB using a 4 x 1 diseqc switch are as follows:
LNB power ------------- ON
LNB Type -------------- Single
LNB Freq -------------- 11250
22 Khz ---------------- OFF
DiSEqC Switch --------- 1.0
Committed -------------- 3 <-- enter diseq switch port # that is hooked to the DN dish.
Legacy SW ------------ Off
At the bottom, you should see a “green” bar chart showing the strengths of the signal;
- Level: ooooooooooooooooooooooooooooo 82%
Quality: oooooooooooooooooooooooooooo 88%
And most important, you should see a satellite ID banner in the upper right corner of the screen showing “Echostar 110 West”. If it is anything OTHER than that your dish is not aimed properly.
If everything is ok, press “EXIT” button and when prompted to SAVE, select “Yes”.
Now you need to scan the satellites for channels. It is extremely important to select “AUTO-SCAN”. Do not select “Blind Scan”
Scan the satellites;
1) Select “Auto Scan” (A-S) in the main menu, press “OK”. Select the satellite to be scanned; in this case, “110.0w Echostar 6.8”.
2) Make sure that “ALL” is highlighted in “Search Type” and “ON” is selected in “Network Search” (N-S).
3) Press “OK” to start the scan.
Any time you "scan" or "re-scan", you should always use "A-S". Due to the 12 min scan time for the 110 sat, you can set "N-S" set to "OFF".
Note that "DN" was used as an example since it is one of the most popular sats in the NorW flash. However, you should scan the sats from highest (119) to lowest (91) in that order. The reason is that the DN channels will be sorted into SID order with BEV channels sorted by SID + 1000.
When complete, the resulting scan will be saved and you can exit to the video screen to watch TV! However, if the keys have not been updated, select a DN channel and wait until the key’s auto-roll. Do the same on a BEV channel. Both will auto-roll in a few minutes.
Download Keymaster off the link below my sig and you will never have to ask for the key codes again.
Jerry
|
|
bill038
Suspended permanently
|
3. August 2007 @ 19:13 |
Link to this message
|
|
I have posted this a dozen times and I am still asked how to do it. If it isn't right in front of some people they will start a new thread and ask it again. I want to help all I can, they are wearing me out.
billo
|
|
MESMD
Member
|
3. August 2007 @ 19:14 |
Link to this message
|
Originally posted by bad_boy69:
anybody with loader for 6000 platinum??? please or where can i get it?? thanks
SIGN IN THE WWW.ELECTRONICGURU.NET. THEN LOOK FOR THE COOLSAT FORUM AND THE 6K RECEIVER. YOU CAN DOWNLOAD THE NORW 145 BIN FOR THE 6K FROM THERE. YOU WILL HAVE TO REGISTER FIRST BUT IT'S FREE.
|
|
coldwell
Junior Member
|
3. August 2007 @ 19:17 |
Link to this message
|
|
If they would just read the postings from you and Jerry all the answers are here.
|
|
bill038
Suspended permanently
|
3. August 2007 @ 19:22 |
Link to this message
|
|
To much work to read
billo
|
AfterDawn Addict
|
3. August 2007 @ 19:49 |
Link to this message
|
Originally posted by bill038:
To much work to read
Makes you wonder sometimes.
Afterdawn isn't setup to be a true FTA forum but this section seems to have become that. I guess its because the other FTA forums have to shut down from the stress at times like we just had. I don't claim to have all the answers and most of the information I pass on comes from other forums. Its just knowing how and where to find the information. If you other members want to link to bin files----setup guides---key sites and general information, I see no problem with that and do exactly that when necessary. Just keep in mind that you shouldn't link to anything that advertises on the main link for profit. If any advertising is involved then Afterdawn should get paid for it. So just keep that in mind when linking. For files, I try to upload to a file sharing site that allows unlimited downloads to keep the load off this site directly.
In most cases, I won't post actual key numbers unless the key site are down or there is confusion over them. They are very easy to find and since they are part of an encryption system, I don't feel its right to post them on open forum. Thats just my opinion but the mods seem to allow it so thats their call. I just don't want to see any problems to surface for Afterdawn over key numbers.
Jerry
|
|
bill038
Suspended permanently
|
3. August 2007 @ 19:57 |
Link to this message
|
|
I have started to refer people to look in the other threads and start reading. It has become the same questions over and over. I will give them all the help I can, but I will no longer post where to get bins nor will I post keys. All that info is everywhere.
billo
|
|
Shamraz
Newbie
|
3. August 2007 @ 20:01 |
Link to this message
|
For bin uploader download plz find attached link
[url=http://forums.f2atv.com/showthread.php?t=28160][/url]
For 1.45 bin download , plz find attached link.
[url=http://files-upload.com/411239/COOLSAT5000_NORW_145_20070801.zip.html][/url]
|
|
lazyuser
Junior Member
|
3. August 2007 @ 20:53 |
Link to this message
|
|
i just got myself a coolsat5000. trying to configure it. it does not gimme the green bars(quality and strenght) when i try 110, 119 and 121 for dishnetwork. i have some international channels too and currently i have a superdish with a smaller dish for my locals.
now, in dish setting, what switch type do i use? OCS-DP, OCS, and so one are listed which one do i use. more importanly, what should my settings be? can anyone help me?
PEACE!
|
|
whyohwhy
Newbie
|
3. August 2007 @ 20:57 |
Link to this message
|
Hi, I have a clone...Koolsat. Can someone help my find the latest autoroll bin for this..if there is one.
Also is there somewhere that I can get key updates as they are available?
|
|
rpanchal
Newbie
|
3. August 2007 @ 22:05 |
Link to this message
|
|
does anyone has the new codes for coolsat 5000?
|
|
rAnDyNeo
Suspended due to non-functional email address
|
3. August 2007 @ 22:08 |
Link to this message
|
hey now i keep changing the code for Dish Network, and i think i need a new bin file for 4000 pro and how to put the bin file in the Coolsat 4000 pro ty..
|
Junior Member
|
3. August 2007 @ 22:14 |
Link to this message
|
If any body need new bin file and Loader, then send me your emails to
cali_cali123@yahoo.com. Please send only YAHOO or HOTMAIL ID's.
Don't send from Gmail.
I have the followong bin files + LOADER
Coolsat 4000: V145
Coolsat 5000: V145
Coolsat 6000: V145
CoolsaT 7000: V111
LOADER
....................................................................
|
|
gerryHer
Newbie
|
3. August 2007 @ 22:58 |
Link to this message
|
|
Is there more keys besides just Dish Network 0101, Bell ExpressVu 0901? If so does The auto roll also update those keys as well??
|
|
jhwkins
Newbie
|
4. August 2007 @ 05:58 |
Link to this message
|
Originally posted by gerryHer:
Is there more keys besides just Dish Network 0101, Bell ExpressVu 0901? If so does The auto roll also update those keys as well??
My 5000 auto rolled fine but is not picking up any channels any suggestions
|
|
bill038
Suspended permanently
|
4. August 2007 @ 06:04 |
Link to this message
|
|
lazyuser says:
i just got myself a coolsat5000. trying to configure it. it does not gimme the green bars(quality and strenght) when i try 110, 119 and 121 for dishnetwork. i have some international channels too and currently i have a superdish with a smaller dish for my locals.
now, in dish setting, what switch type do i use? OCS-DP, OCS, and so one are listed which one do i use. more importanly, what should my settings be? can anyone help me?
Please read the install guide that Jerry posted right above your post.
billo
|
|
bill038
Suspended permanently
|
4. August 2007 @ 06:07 |
Link to this message
|
If you have a clone, you are out of luck for the time being. The coders that make the bin files for the ligit boxes will not write the code for the clones. Someone takes the code for the ligit boxes and modifies it for the clones, it takes a while for this to happen
billo
|
|
bill038
Suspended permanently
|
4. August 2007 @ 06:11 |
Link to this message
|
|
rpanchal: & rAnDyNeo:
Please read ALL the other threads. ALL your answers have been answered. You just have to research the other threads. There is no quick fix with out READING.
billo
|
|
bill038
Suspended permanently
|
4. August 2007 @ 06:15 |
Link to this message
|
|
gerryHer: The keys are put out in a stream from the sat providers to change the encryption. As many sat providers as you get, you sill be receiving a different set of keys. The providers change them all the time to keep people from getting free tv.
billo
|
|
Advertisement
|
|
|
|
bill038
Suspended permanently
|
4. August 2007 @ 06:17 |
Link to this message
|
|
jhwkins: This has been addressed in other threads. Please read.
billo
|
