Moved to Here http://forums.afterdawn.com/thread_view.cfm/531363

WE HAVE NOW MOVED TO THIS PAGE

http://forums.afterdawn.com/thread_view.cfm/531375#3215802

 

So, this is my new home eh?

Looks tidy

 

i've arrived hi everyone wow great place

 

Codes are further down

 

codes further down

 

29/06/07
n*l ireland
00 db 69 7d 22 b1 fd 6d ed
01 9e 40 85 78 e7 82 10 06

 

Sound Problems

To get back sound on e4 sky1 ect just select the channel in question press menu,
select installation, select manual scan, click ok on down frequency.
It'll now scan for channels when its finished exit back to normal
tv viewing screen go to the end of your channel listing and the desired channel will be there with sound.
This can be done on any channel with no sound by just selecting that channel following the instructions above.
Hope this helps

 

hello

 

ferg you nearly for got the irish sure yea culd'nt be doing that slán

 

marti, will your box not power up at all

 

what times the house warming at?

 

If you have a Bad Flash with software have a Read of This might help

If you have a bad flash, switch it off then on at the back & make sure its on standby.
Then Flash as normal. This also applies to flashing (up & downloading) the channel data file.
If for some reason you cannot flash and have set and checked everything else such as ports and connections,
then you should switch off at the back wait a moment then on again. Then try to flash again.

If for some reason it won't go into standby and you see a constant moving green line.
you may want to wait to see if it goes into standby or switches on eventually or re-flash from this state
though it may not work. Some users have reported that flashing an older firmware 1st that was working,
then trying again may help. If your flash has failed or corrupted try again but 1st flash back the firmware
that was on before your failed flash. Re download the firmware just in case you had a corrupted file then try again.
If you do flash from the moving green line state at boot, you will see the % increase on the GTRom loader
software but not on the starview. Toward the end of the flash you'll see a Flash Burning message in GTRom.
Make sure you wait until all is finished and you see the Download complete pop up message in GTRom.

Another method you can use to recover from a bad flash, eg. the box won't boot to standby and is stuck
in pre standby, either after about 3 or 4 moving green lines the box sticks with the green line not moving
at all or it keeps moving forever. If the box will NOT RE-FLASH as normal from on or standby, try this but it
may take a few goes to work.

Connect the box to the pc with your cable but switch it off at the back. Load the correct
firmware bin file into GTRom & set it to the correct com port, and select App file only then hit Download.
Only then switch on at the back to power on the box. It may take a few sec. so wait at least 30 sec.
(If it doesn't work 1st time try also waiting a couple of sec. to switch on after pressing download in the loader.) It may take more than 1 try to work, but eventually you'll see the loader kick in and the % bar increase. You won't see the % on the Starview though. Only green lines moving left to right. Towards the end of the flash you'll see a message in GTRom saying FLASH BURNING. Then it will reach 100% and wait for the download complete pop up box to appear & the box will reboot back to factory setup. You will have lost any channel data previously on the box & will need to rescan & switch on EMU and set the box up from scratch.

If you don't know the state of the box switch it on see what happens see if there already has been a channel
scan done before-meaning there are channels on it working or not. If so tune to an unencrypted channel as above
then standby then re-flash.

 

no.... plug it in no lights not tried a multi meter yet

 

dont no one go sitting in my ass groove on the sofa ok

 

yea i know only kidding also it is best to keep us apart cause when i first tried to input codes i was inputting n.. uk so your right

 

LATEST CODES

NTL UK:
00: 3d 2b df aa 51 c8 dd a0
01: E2 C9 74 0A 04 22 A6 12

C&W
00: 1F EE 87 F9 E3 FA 2A AB
01: 5B 36 AE 71 F5 21 D1 3D

Telwest
00: AB 1E 05 EB C6 65 46 77
01: 51 6D 0F 08 41 BB D5 D8


Chorus codes

key00:24 1B 73 09 9C 3A 37 88
key01:81 34 4B 3C 9E DF 10 67


Nthell dublin code

00 = DB 69 7D 22 B1 FD 6D ED
01 = 49 EC A4 0C 4F A0 30 CB

chorus frequencies set symbol rate 6875
274.000 371.000 works
282.000 378.000
290.000 386.000 works
298.000 394.000 works
306.000 410.000 works
314.000 426.000
322.000 works 347.500 works

 

Hello to ALL the GURU's out there, I have been following you lads n lassie and my box of treats is still working on 2.57 with manual code updates. Thanks a million!!!!Keep it going, long live Starview n you GURU's!!!!BTW am a Complete novice, but am learning.

 

ferg how do you edit a post

 

if you have Missing channels you can try this.

I have seen a few posts about channels missing when doing a full scan.
Here's a little trick you can try that may help if you're having problems
finding any particular channels or are missing channels:
Try and determine the lowest transponder frequency that you can get a signal on.
Look at the frequencies you already have on the channels saved so far and choose the lowest.
Then in the installation menu select MANUAL SCAN and set that as the frequency.
Make sure you can see a signal and scroll down to Network scan and change to ENABLE with the Right arrow.
While still highlighted, click OK.
Scanning should then begin. It will say 1/1 to start with but should then jump up to 1/?? (the ?? being 2 digits).
Using this method my Starview indicated it scanned 56/56 transponder frequencies as opposed to 48 in Auto scan on one main provider.
I also gained a few extra channels.
The other transponders may have been picked up by scanning other providers.

 

lol, we're all going to be mods at this rate