1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

pleas help, no power, viper, pulling my hair out

Discussion in 'Nintendo Gamecube - General discussion' started by amsol, Jan 31, 2005.

  1. amsol

    amsol Member

    Joined:
    Jan 31, 2005
    Messages:
    16
    Likes Received:
    0
    Trophy Points:
    11
    OK i searched but dident find this prob anywhere. Just installed my viper, no problem. Started my cube, booted up origanal, hadent flashed yet couse I wanted to make sure the install was good opened the cover and the sensor bypass worked. I flashed the viper with cobra 4 turned my cube on and nothing, dvd wont spin. The fan works the LED works, my altmeter tells me Im getting power to the chip and the cover sensor everything. My install looks good and I verified my flash. What could possibly be wrong. Thanks
     
    amsol, Jan 31, 2005
    #1
  2. gjac1

    gjac1 Member

    Joined:
    Jan 26, 2005
    Messages:
    8
    Likes Received:
    0
    Trophy Points:
    11
    Make sure you have pushed down the connector for the laser unit into the bottom motherboard unit.

    It happened to me once after i tweked the laser, i **** myself.

    Hope this helps m8
     
    gjac1, Feb 1, 2005
    #2
  3. amsol

    amsol Member

    Joined:
    Jan 31, 2005
    Messages:
    16
    Likes Received:
    0
    Trophy Points:
    11
    Its in there as far as I can tell with out being able to see it, it looks lined up. Still no power to the dvd. I removed the viper, still no power. It is possible that the yellow wire made contact with the heatsink during reassembly, could this be the cause of my problem and if so can I just install a new dvd drive, thanks
     
    amsol, Feb 1, 2005
    #3
  4. speedi

    speedi Member

    Joined:
    Dec 24, 2004
    Messages:
    66
    Likes Received:
    0
    Trophy Points:
    16
    Man Amsol you are so Lucky

    Recently I experienced the same thing.

    This is the solution.
    Make sure safe mode is on in the Viper tool.
    Than flash with the 0.3 BIOS (very important).
    Compare the written Flash.
    Then it should work again. I played for a while, and than flashed with the 0.4 again. No problems after that.

    This was my own cube (Rev 16)

    Description of the symptoms.
    No discspining
    No Video
    (I really thought it was dead :)
     
    speedi, Feb 1, 2005
    #4
  5. amsol

    amsol Member

    Joined:
    Jan 31, 2005
    Messages:
    16
    Likes Received:
    0
    Trophy Points:
    11
    I think its done for, I removed the viper and still no spin, no original boot, just a black screen. I know a signal is sent to the tv cause the screen flashes then goes black. Is it possible I could save my cube if I reinstall the viper and flash it as you suggested? thanks
     
    amsol, Feb 1, 2005
    #5
  6. amsol

    amsol Member

    Joined:
    Jan 31, 2005
    Messages:
    16
    Likes Received:
    0
    Trophy Points:
    11
    The viper is in and running, When I put the lid back on it snagged the yellow wire and instead of pulling the wire off the connector it pulled the connector off the mobo(I know I'm a clumsy fool)I soldier it back to mobo and booted right up. I was so careful I dont know how I let this happen. Im so happy to have it working I dont even care that there isn't any audio, but if by chance anyone knows how I might have killed my audio or how I might fix it please let me know. Thanks
     
    amsol, Feb 5, 2005
    #6

Share This Page