|
Wireless Laptop to PS2 Network adapter!!
|
|
|
golden_35
Member
|
10. January 2004 @ 12:25 |
Link to this message
|
|
you can either run an ethernet cable from one of the four places in the back of the router or you can buy a wireless media station from linksys which makes it so your ps2 can be in anyroom that is not near your router
|
|
Advertisement
|
|
|
|
|
actingbiz
Newbie
|
10. January 2004 @ 17:26 |
Link to this message
|
|
ok but how much is it. im at a friends house so i cant check it now so could som 1 tell me how much it costs
|
|
teg9
Junior Member
|
10. January 2004 @ 20:52 |
Link to this message
|
|
Since you have a wireless router I'm assuming that you are using it with a wireless laptop. All you need is just the PS2 network adapter and a crossover patch cable. It'll cost you below 50 bucks for both. Just read my last post on how to make it work.
|
|
TheGr8One
Suspended due to non-functional email address
|
15. January 2004 @ 19:42 |
Link to this message
|
|
Hey, i am haveing a very similar problem to that of teg, i recently bought a network adapter for my ps2, however the wireless router for my house is not located in my room. Since i am using a wireless card on the computer i have an open ether net port when have connected my ps2, unfortunetly i can't figure out how to get the ps2 to work. i tried the bridge thing and all it did was make me unable to surf the net. Please, when it comes to networking i'm pretty basic i need help, i have been sercging for over 3 hours and i think you guys understand my problem best. Please break it down as simplest as possible cuz i dono whats goign on and i think i'm making things worse
|
|
teg9
Junior Member
|
18. January 2004 @ 21:42 |
Link to this message
|
|
TheGr8One u don't need to bridge anything, you just need to make changes on the wireless router configuration to distribute a new set of IP instead of the default 192.168.0.1 adresses and then enable ICS internet connection sharing on your wireless connection by going to the network connections and then right clicking on the wireless connection to turn on ICS.
"I got this all figured out and was just too lazy to post the result. Like what Ranchido said if your router uses 192.168.0.1 IP adresses as default, you can't just enable ICS, first you need to change the settings for the router to give out 192.168.1.x and so on. And then just right click on the wireless network connection and then enable the ICS. Just connect your ps2 to the ethernet jack of the laptop with a CROSSOVER PATCH cable and configure a new connection on the ps2 then you should be able to go online through your wireless laptop."
|
|
snoopid
Suspended due to non-functional email address
|
22. January 2004 @ 10:37 |
Link to this message
|
|
sorry I'm working on this too.. but do you configure the router or the access point? I'm having a little trouble with getting ICS on my wireless connection
|
|
snoopid
Suspended due to non-functional email address
|
22. January 2004 @ 12:13 |
Link to this message
|
|
ok.. i follow everything can now i have ICS but when i get on my PS2 i connect and then get this error DNAS (-611).. am i not configuring my PS2 right? if u could help me out i would really apreciate it.. thanks
IP. 192.168.1.4
Subnet Mask. 255.255.255.0
Default Gateway. 192.168.1.1
|
|
actingbiz
Newbie
|
22. January 2004 @ 12:19 |
Link to this message
|
|
ok lemme get this straight. i havea whireless laptop with a linksys network. i have an internal wirless card so i need to but the adapter and a crossover cord. what is that and what type of ends does it have (a USB hub or a network cable what...)
www.bbfree.com/TheGTA
Join my website!!!
Me? I always tell the truth. Even when I lie.
~Al Pachino SCARFACE
|
|
teg9
Junior Member
|
23. January 2004 @ 23:54 |
Link to this message
|
|
got that 611 error but never found out what it means, maybe you're running a firewall? Try shuting it down if you have one. A crossover cable is just like your ethernet cable but with a different wiring pattern.
|
|
TheGr8One
Suspended due to non-functional email address
|
25. January 2004 @ 18:56 |
Link to this message
|
|
dang, i get the same dnas error, wtf, i am so close
|
|
golden_35
Member
|
25. January 2004 @ 22:53 |
Link to this message
|
|
I get the same problem! but i am running my ps2 right to my linksys router with a straight ethernet cable!!! What the heck? And yes, it is in sleep mode!
|
|
TheGr8One
Suspended due to non-functional email address
|
26. January 2004 @ 18:29 |
Link to this message
|
|
Ah, does anyone know how to fix this? I'm so close, the ps2 connects and everything but like when i'm about to play madden 2004 its says doing something about dnas and then i get dnas error -611. Why!!!!! I just wanna play!
|
|
snoopid
Suspended due to non-functional email address
|
26. January 2004 @ 19:18 |
Link to this message
|
|
sorry i havent been on my computer because ive been playin online..ha i figure it out somehow i dno.. u have to my ur connection from ur computer to ur ps2 make sure tha IP is 192.168.0.1.. once i got that IP on my connection everything started to work perfect. this was my only option since i have a wireless A and there are no bridges compatable with this wireless type so thanks for all tha post to help me figure this out!! :)
|
|
snoopid
Suspended due to non-functional email address
|
26. January 2004 @ 19:28 |
Link to this message
|
|
you might have to turn off ur modem, router,access point and computers, then turn them back on to get that IP im not sure but thats how it works
|
|
golden_35
Member
|
26. January 2004 @ 20:18 |
Link to this message
|
|
that does not make any sense, how could your ip address change from a simple reboot?
|
|
teg9
Junior Member
|
27. January 2004 @ 19:00 |
Link to this message
|
|
golden_35 when you change the IP distributions on the router you need to reboot all pc's that are in the network to release the old IP and get the new IP adresses. Then go to View Network Connections then rightclick on the wireless connection to enable ICS, giving the wireless network connection 168.192.0.1 IP adress. Then you should see the shared big hand sign on the wireless connection. After that you just need to set up a new connection on your PS2 NA. let me know if this works out.
|
|
golden_35
Member
|
27. January 2004 @ 19:42 |
Link to this message
|
|
what does DNAS error -880 mean??? I am getting that one now
|
|
teg9
Junior Member
|
28. January 2004 @ 18:59 |
Link to this message
|
|
never seen that before. What chip do you have? YOu might be having problem on putting it on sleep mode.Try putting the chip on sleep mode and then try to load a burnt game which shouldn't load if its really on sleep mode. I don't know what else...try going to playstation.com they got a pretty big forum in there.
|
|
inssain96
Newbie
|
23. February 2004 @ 09:52 |
Link to this message
|
|
Good idea, who ever thought of it!
Getting it working was cake, I've only seen one problem...can't get the headset to work when playing SOCOM II. If I connect directly to the linksys from the ps2 I have no problems, so I don't think it's a setting on the linksys. There were no specific rules in the ICS settings. Anyone else have this problem?
|
|
illskillz
Newbie
|
1. April 2004 @ 07:05 |
Link to this message
|
|
one short question....will i be able to play my ps2games online if they are burned copies???
i have one of the older versions of ps2 (not sure what ver. no--but i bought it the year it came out) and i can't recall what chip i have installed either.
|
|
teg9
Junior Member
|
1. April 2004 @ 17:36 |
Link to this message
|
|
you can't play online with burnt games
|
|
Icemonkey
Senior Member
|
2. April 2004 @ 03:28 |
Link to this message
|
|
Note also that if you change your DHCP address allocation pool, you don't need to reboot the client PC's/Devices, Windows clients that support the IPCONFIG command from the command prompt can type IPCONFIG /RELEASE and IPCONFIG /RENEW to obtain the new address without a reboot. Windows 95/98 clients can accomplish the same thing with the WINIPCFG command.
PS2 - v8
Mod - Magic V
Burner - CenDyne (Pioneer) DVR-A05
Media - Anything Cheap
Gamecube w/Broadband Adapter
Phantasy Star Online
Animal Crossing Loader v1.4
Phantasy Star Uploader v1.1
Gamecube ISO Ripping Server v1.0.0.29 |
|
abdallah
Suspended due to non-functional email address
|
2. May 2004 @ 18:13 |
Link to this message
|
|
What do you use when you configure a new connection on the ps2? I tried different things, but the connection was never made.
Also to add various IP address ranges, how is that done? Filters?
any additional info. would be helpful
[URL]www.SPUBS.com[/URL]
|
|
teg9
Junior Member
|
2. May 2004 @ 23:51 |
Link to this message
|
|
you're not going to add IP addresses you need to change the routers IP add. distribution, if it uses 192.168.0.1 addresses, in your routers settings.
"you can't just enable ICS, first you need to change the settings for the router to give out 192.168.1.x and so on. And then just right click on the wireless network connection and then enable the ICS. Just connect your ps2 to the ethernet jack of the laptop with a CROSSOVER PATCH cable and configure a new connection on the ps2 then you should be able to go online through your wireless laptop."
|
|
Advertisement
|
|
|
|
abdallah
Suspended due to non-functional email address
|
3. May 2004 @ 09:58 |
Link to this message
|
|
How do you "change the routers IP add. distribution"? I believe that I have done this already, and I initiated (ICS); but it still does not connect
_
[URL]www.SPUBS.com[/URL]
This message has been edited since posting. Last time this message was edited on 4. May 2004 @ 04:31
|
