Originally posted by 1shaddow1:

---

not quoting the whole thing again john but i hope it all goes well for ya :-)

a jus try n help people all i can however, i am not a mountain of knowledge as there is far more experienced people on here.

anyhow i gotta shoot for a few hour, will be back later if you need more help.

take care

andy

---

Thanks Andy for the input.

[

John, You are compounding his/her error by repeating the obvious mate, It would be better if you edit your message, it will be easier all round, I know it is frustrating but you are also shouting.

Hey sc0user - thanks for that info yesterday.

I grabbed the CDF that you gave but it didn't work (or seem to work) when I downloaded to the box using the interface (flash loader) - it actually just appeared to run through the firmware upgrade again despite the fact that I had browsed to the CDF on my desktop.

Just wanted to give you feedback on that...did I need to do anything specific to download the channel list??
In any case I went to your plan 'B' and just did a scan between the baud rates defined and everything worked fine. How long do you think this firmware will be good enough for before NTSmell react???

I've family looking for me now to fix their so I'll have my little workshop open soon... thank again for you help & also to Lenny if you're reading this...

Chopper79 - no issue. I thought a newbie might help another newbie!
Although I got a kurt reply from one of the mods about the msg I sent. I reckon it was cos I enclosed a link to BM toolbar. Anyway all sorted now.

Originally posted by malci:

---

John, You are compounding his/her error by repeating the obvious mate, It would be better if you edit your message, it will be easier all round, I know it is frustrating but you are also shouting.

---

Malci
Your comments have been taken on board, it's just soooooo annoying when we all know the story now.

And yes I was shouting, but I knew that, just having a tantrum

Cheers

:-)

Originally posted by JaneyMack:

---

Hey sc0user - thanks for that info yesterday.

I grabbed the CDF that you gave but it didn't work (or seem to work) when I downloaded to the box using the interface (flash loader) - it actually just appeared to run through the firmware upgrade again despite the fact that I had browsed to the CDF on my desktop.

Just wanted to give you feedback on that...did I need to do anything specific to download the channel list??
In any case I went to your plan 'B' and just did a scan between the baud rates defined and everything worked fine. How long do you think this firmware will be good enough for before NTSmell react???

I've family looking for me now to fix their so I'll have my little workshop open soon... thank again for you help & also to Lenny if you're reading this...

---

Same here on the CDF file.
Just did a power scan and all was well in the end.
Thanks, sc0user for the file anyway.

Originally posted by rehammot:

---

How do I disable the new channel sort facility for the Eurovox please. I find it most annoying. Thanks for any help.

---

read back a few posts its on here somewhere something to do with the yellow button i thinks - ive not done mine coz im happy with its sorting in alpha mode

trelock: sending me private msgs asking for keys is useless as i live in the uk and do not have ch@rus keys.

besides its still against the rules to beg for keys and i do not want my private box filled up with requests like that.

hope that answered your question.

andy

Originally posted by JaneyMack:

---

Hey sc0user - thanks for that info yesterday.

I grabbed the CDF that you gave but it didn't work (or seem to work) when I downloaded to the box using the interface (flash loader) - it actually just appeared to run through the firmware upgrade again despite the fact that I had browsed to the CDF on my desktop.

Just wanted to give you feedback on that...did I need to do anything specific to download the channel list??
In any case I went to your plan 'B' and just did a scan between the baud rates defined and everything worked fine. How long do you think this firmware will be good enough for before NTSmell react???

I've family looking for me now to fix their so I'll have my little workshop open soon... thank again for you help & also to Lenny if you're reading this...

---

Did you by any chance happen to hit the 'top' download button instead of the one at the bottom?
The top download button is to flash the box, and the bottom section is for uploading/downloading your CDF file, the download of the CDF file should only take a few seconds.

Originally posted by SG8:

---

Originally posted by JaneyMack:

---

Hey sc0user - thanks for that info yesterday.

I grabbed the CDF that you gave but it didn't work (or seem to work) when I downloaded to the box using the interface (flash loader) - it actually just appeared to run through the firmware upgrade again despite the fact that I had browsed to the CDF on my desktop.

Just wanted to give you feedback on that...did I need to do anything specific to download the channel list??
In any case I went to your plan 'B' and just did a scan between the baud rates defined and everything worked fine. How long do you think this firmware will be good enough for before NTSmell react???

I've family looking for me now to fix their so I'll have my little workshop open soon... thank again for you help & also to Lenny if you're reading this...

---

Did you by any chance happen to hit the 'top' download button instead of the one at the bottom?

---

I'm pretty sure I tried both....but it just seemed to kick-off the firmware upgrade again and not a channel download despite the fact that the file I had browsed to/selected was the required CDF.
Like I said not a biggie - I did a scan but just wanted to see if I could sort it as will have to repeat the download 2 or 3 more times....cheers.

Originally posted by SG8:

---

Originally posted by JaneyMack:

---

Hey sc0user - thanks for that info yesterday.

I grabbed the CDF that you gave but it didn't work (or seem to work) when I downloaded to the box using the interface (flash loader) - it actually just appeared to run through the firmware upgrade again despite the fact that I had browsed to the CDF on my desktop.

Just wanted to give you feedback on that...did I need to do anything specific to download the channel list??
In any case I went to your plan 'B' and just did a scan between the baud rates defined and everything worked fine. How long do you think this firmware will be good enough for before NTSmell react???

I've family looking for me now to fix their so I'll have my little workshop open soon... thank again for you help & also to Lenny if you're reading this...

---

Did you by any chance happen to hit the 'top' download button instead of the one at the bottom?
The top download button is to flash the box, and the bottom section is for uploading/downloading your CDF file, the download of the CDF file should only take a few seconds.

---

For my part I did it right but it only downloaded 13 channels, so the scan brought in the rest

John my CDF is for N** Dublin and it brings in 13 Transponders giving a total of 138 TV channels the rest are radio ;)

Originally posted by sc0user:

---

John my CDF is for N** Dublin and it brings in 13 Transponders giving a total of 138 TV channels the rest are radio ;)

---

Hi sc0user,
Yeah I downloaded it in the lazy hope I wouldn't have to do anything else, but I did in the end, thanks anyway.
Must be something I did.
The new EPG is cool though...:-)
Cheers
John

Yep new EPG is good but whats under the hood in regards to emulation, AU, etc you would be more impressed with ;)

Originally posted by sc0user:

---

Yep new EPG is good but whats under the hood in regards to emulation, AU, etc you would be more impressed with ;)

---

On the readme file it said quicker AU, with last nights roll did it update faster???

Do you know of a download for EPG Starview??

Lot more to it than just a faster keyroll..... believe me ;)

The SV EPG has always been bad, although improved on the SV3. Sorry to say you are stuck with it.

BTW I think what happened with my CDF was you didnt clear your channel data first before downloading it, presuming you are on N** Dublin.

Originally posted by sc0user:

---

Lot more to it than just a faster keyroll..... believe me ;)

The SV EPG has always been bad, although improved on the SV3. Sorry to say you are stuck with it.

BTW I think what happened with my CDF was you didnt clear your channel data first before downloading it, presuming you are on N** Dublin.

---

Yeah, I am on NTHell Dublin.
Yep sounds like something I would do on the non-clearing of channels part. Not to worry, if I have to do one for somebody else I will know then.
Cheers

Hi!
Just wondering if anyone has the same problem with their digivox images changing size constantly.
It seems that the size imgage is changin from wide screen to zoom size is there something that I need to set up to avoid this happening.
I have check from the normal channels and it doesn't happen
Hope someone can help
Thanks

Originally posted by Cmcmcmcm:

---

Hi!
Just wondering if anyone has the same problem with their digivox images changing size constantly.
It seems that the size imgage is changin from wide screen to zoom size is there something that I need to set up to avoid this happening.
I have check from the normal channels and it doesn't happen
Hope someone can help
Thanks

---

Try going into your menu and then the settings for screen size and select normal or letterbox size and save it at that.

Originally posted by johnfb:

---

Originally posted by Cmcmcmcm:

---

Hi!
Just wondering if anyone has the same problem with their digivox images changing size constantly.
It seems that the size imgage is changin from wide screen to zoom size is there something that I need to set up to avoid this happening.
I have check from the normal channels and it doesn't happen
Hope someone can help
Thanks

---

Try going into your menu and then the settings for screen size and select normal or letterbox size and save it at that.

---

Thanks for that but it is not working.
Just went into TV settings and it was already set up for letter box, tried to mess around with it but it not changing anything and it keeps on jumping size and it is very annoying.

Originally posted by Cmcmcmcm:

---

Originally posted by johnfb:

---

Originally posted by Cmcmcmcm:

---

Hi!
Just wondering if anyone has the same problem with their digivox images changing size constantly.
It seems that the size imgage is changin from wide screen to zoom size is there something that I need to set up to avoid this happening.
I have check from the normal channels and it doesn't happen
Hope someone can help
Thanks

---

Try going into your menu and then the settings for screen size and select normal or letterbox size and save it at that.

---

Thanks for that but it is not working.
Just went into TV settings and it was already set up for letter box, tried to mess around with it but it not changing anything and it keeps on jumping size and it is very annoying.

---

its probably the format in which the prog is filmed in.
Do you have auto on your tv soemtimes we have to kepe changing box or tv from WS to letterbox to full auto etc etc depending on the channel and the fomrat its filmed in. adverts are fine. I think dependsing on the make model of tv ocne yove changed the format from 16:9 to say 4:3 you have to change tv channels or turn tv on/off again to set it. try that.

Originally posted by linny40:

---

Originally posted by Cmcmcmcm:

---

Originally posted by johnfb:

---

Originally posted by Cmcmcmcm:

---

Hi!
Just wondering if anyone has the same problem with their digivox images changing size constantly.
It seems that the size imgage is changin from wide screen to zoom size is there something that I need to set up to avoid this happening.
I have check from the normal channels and it doesn't happen
Hope someone can help
Thanks

---

Try going into your menu and then the settings for screen size and select normal or letterbox size and save it at that.

---

Thanks for that but it is not working.
Just went into TV settings and it was already set up for letter box, tried to mess around with it but it not changing anything and it keeps on jumping size and it is very annoying.

---

its probably the format in which the prog is filmed in.
Do you have auto on your tv soemtimes we have to kepe changing box or tv from WS to letterbox to full auto etc etc depending on the channel and the fomrat its filmed in. adverts are fine. I think dependsing on the make model of tv ocne yove changed the format from 16:9 to say 4:3 you have to change tv channels or turn tv on/off again to set it. try that.

---

It happens in all the channels not just the one program, it used to work fine for the last few weeks since I have it updates and even this morning but now can even watch it as it jumps constantly. Do u think that I need to reprogram the box or reset it.

oh dunno sounds weird but well its worth a try! or do you have a diff scart socket to try, and have you checked that all leads are pushed in right - that might be a problem.
tbh ive never heard of this problem on here, maybe one of the experts will see this later and be able to help

Originally posted by linny40:

---

oh dunno sounds weird but well its worth a try! or do you have a diff scart socket to try, and have you checked that all leads are pushed in right - that might be a problem.
tbh ive never heard of this problem on here, maybe one of the experts will see this later and be able to help

---

have to say i ain't heard of this prob only when they broadcast in diff formats.

is it at all poss the box is at fault? that is to say faulty?