after initial setup ... i pressed burn and nero failed less than 10s.. here's my log Windows XP 5.1 IA32 WinAspi: - ahead WinASPI: File 'C:\Program Files\Ahead\Nero\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 10/26/2004 6:35:34 PM Nero Version: 6.6.0.16 Internal Version: 6, 6, 0, 16b Recorder: <PIONEER DVD-RW DVR-105> Version: 1.33 - HA 1 TA 1 - 6.6.0.16 Adapter driver: <atapi> HA 1 Drive buffer : 2000kB Bus Type : default (0) -> ATAPI, detected: ATAPI CD-ROM: <HL-DT-ST CD-ROM GCR-8520B>Version: 1.00 - HA 1 TA 0 - 6.6.0.16 Adapter driver: <atapi> HA 1 === Scsi-Device-Map === DiskPeripheral : WDC WD200EB-00CSF0 atapi Port 0 ID 0 DMA: On DiskPeripheral : ST380011A atapi Port 0 ID 1 DMA: On CdRomPeripheral : HL-DT-ST CD-ROM GCR-8520B atapi Port 1 ID 0 DMA: Off CdRomPeripheral : PIONEER DVD-RW DVR-105 atapi Port 1 ID 1 DMA: On === CDRom-Device-Map === HL-DT-ST CD-ROM GCR-8520B E: CDRom0 PIONEER DVD-RW DVR-105 F: CDRom1 ======================= AutoRun : 1 Excluded drive IDs: WriteBufferSize: 83886080 (0) Byte ShowDrvBufStat : 0 BUFE : 0 Physical memory : 1023MB (1047792kB) Free physical memory: 656MB (672488kB) Memory in use : 35 Uncached PFiles: 0x0 Use Inquiry : 1 Global Bus Type: default (0) Check supported media : Disabled (0) 1.8.2005 Burn DVD Image 9:17:04 PM #1 Text 0 File Reader.cpp, Line 127 Reader running 9:17:04 PM #2 Text 0 File Writer.cpp, Line 122 Writer PIONEER DVD-RW DVR-105 running 9:17:04 PM #3 Text 0 File Burncd.cpp, Line 3233 Turn on Disc-At-Once, using DVD media 9:17:40 PM #4 Text 0 File DlgWaitCD.cpp, Line 270 Last possible write address on media: 2298495 (510:46.45, 4489MB) Last address to be written: 2201429 (489:12.29, 4299MB) 9:17:40 PM #5 Text 0 File DlgWaitCD.cpp, Line 282 Write in overburning mode: NO (enabled: CD) 9:17:40 PM #6 Text 0 File DlgWaitCD.cpp, Line 2483 Recorder: PIONEER DVD-RW DVR-105, Media type: DVD-R Disc Manufacturer: SONY08 - D1 Disc Application Code: 64, Disc Physical Code: 193 9:17:40 PM #7 Text 0 File DlgWaitCD.cpp, Line 448 >>> Protocol of DlgWaitCD activities: <<< ========================================= Not enough free discspace. (Medium in drive: DVD-R. Medium required by compilation: DVD-R/RW.) 9:17:40 PM #8 Text 0 File ThreadedTransferInterface.cpp, Line 838 Setup items (after recorder preparation) 0: TRM_DATA_MODE1 (2 - CD-ROM Mode 1, ISO 9660) 2 indices, index0 (150) not provided original disc pos #0 + 2201430 (2201430) = #2201430/489:12.30 not relocatable, disc pos for caching/writing not required/not required, no patch infos -> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2201430 blocks [PIONEER DVD-RW DVR-105] -------------------------------------------------------------- 9:17:40 PM #9 Text 0 File ThreadedTransferInterface.cpp, Line 1051 Prepare recorder [PIONEER DVD-RW DVR-105] for write in CUE-sheet-DAO DAO infos: ========== MCN: "" TOCType: 0x00; Session Closed, disc not fixated Tracks 1 to 1: 1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4508528640, ISRC "" DAO layout: =========== __Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________ 0 | lead-in | 0 | 0x41 | 0x00 0 | 1 | 0 | 0x41 | 0x00 0 | 1 | 1 | 0x41 | 0x00 2201430 | lead-out | 1 | 0x41 | 0x00 9:17:40 PM #10 Phase 24 File dlgbrnst.cpp, Line 1832 Caching of files started 9:17:40 PM #11 Text 0 File Burncd.cpp, Line 4120 Cache writing successful. 9:17:40 PM #12 Phase 25 File dlgbrnst.cpp, Line 1832 Caching of files completed 9:17:40 PM #13 Phase 36 File dlgbrnst.cpp, Line 1832 Burn process started at 4x (5,540 KB/s) 9:17:40 PM #14 Text 0 File ThreadedTransferInterface.cpp, Line 2654 Verifying disc position of item 0 (not relocatable, no disc pos, no patch infos, orig at #0): write at #0 9:17:40 PM #15 Text 0 File DVDR.cpp, Line 2379 Recording mode: Sequential Recording Mode for Multisession 9:17:40 PM #16 Text 0 File Mmc.cpp, Line 21708 Set BUFE: Buffer underrun protection -> ON 9:17:40 PM #17 Text 0 File DVDR.cpp, Line 2534 Start write address at LBA 0 DVD high compatibility mode: Yes 9:17:40 PM #18 Text 0 File Cdrdrv.cpp, Line 8862 ---- DVD Structure: Physical Format Information (00h) ---- Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050 Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 0.0 (0) Disc Size: 120 mm, Maximum Rate: 10.08 Mbps (2 h) Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable Linear Density: 0,267 um/bit, Track Density: 0,74 um/track Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW) End Physical Sector Number of Data Area: 0 h End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB) Data in Burst Cutting Area (BCA) does not exist Start sector number of the current Border-Out: 0 h Start sector number of the next Border-In: 0 h Media Specific [16..63]: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 9:17:45 PM #19 Text 0 File Cdrdrv.cpp, Line 1286 21:17:45.484 - PIONEER DVD-RW DVR-105\H1 T1 : Queue again later 9:18:04 PM #20 SCSI -1183 File Cdrdrv.cpp, Line 1434 SCSI Exec, HA 1, TA 1, LUN 0, buffer 0x04380000 Status: 0x04 (0x01, SCSI_ERR) HA-Status 0x00 (0x00, OK) TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND) Sense Key: 0x08 (KEY_BLANK_CHECK) Sense Code: 0x00 Sense Qual: 0x00 CDB Data: 0x2A 0x00 0x00 0x00 0x03 0x00 0x00 0x00 0x20 0x00 0x00 0x00 Sense Data: 0xF1 0x00 0x08 0xFF 0xFF 0x03 0xF0 0x0E 0x00 0x00 0x00 0x00 0x00 0x00 9:18:04 PM #21 CDR -1183 File Writer.cpp, Line 311 Blank check command error PIONEER DVD-RW DVR-105\H1 T1 9:18:04 PM #22 Text 0 File ThreadedTransfer.cpp, Line 228 all writers idle, stopping conversion 9:18:05 PM #23 Text 0 File ThreadedTransfer.cpp, Line 222 conversion idle, stopping reader 9:18:05 PM #24 Text 0 File DVDR.cpp, Line 2774 EndDAO: Last written address was 767 9:18:05 PM #25 Phase 133 File dlgbrnst.cpp, Line 1832 Writing short lead-out 9:18:05 PM #26 SCSI -1176 File Cdrdrv.cpp, Line 1180 SCSI Exec, HA 1, TA 1, LUN 0 Status: 0x04 (0x01, SCSI_ERR) HA-Status 0x00 (0x00, OK) TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND) Sense Key: 0x05 (KEY_ILLEGAL_REQUEST) Sense Code: 0x72 Sense Qual: 0x04 CDB Data: 0x5B 0x01 0x02 0x00 0x00 0x03 0x00 0x00 0x00 0x00 0x00 0x00 Sense Data: 0x70 0x00 0x05 0x00 0x00 0x00 0x00 0x0E 0x00 0x00 0x00 0x00 0x72 0x04 9:18:05 PM #27 CDR -1176 File WriterStatus.cpp, Line 167 Session fixation error 9:18:05 PM #28 TRANSFER -24 File WriterStatus.cpp, Line 167 Could not perform end of Disc-at-once 9:18:05 PM #29 Phase 38 File dlgbrnst.cpp, Line 1832 Burn process failed at 4x (5,540 KB/s) Existing drivers: File 'Drivers\PXHELP20.SYS': Ver=2.03.28a, size=20640 bytes, created 3/11/2005 4:28:13 PM (Prassi/Veritas driver for win 2K) File 'Drivers\atapi.sys': Ver=5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), size=95360 bytes, created 8/3/2004 10:59:44 PM (Adapter driver for rec) Registry Keys: HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
Looking good here, everything seems to be the latest. It looks like your dvd recorder is up to date, but if you have the SONY OEM, then it's firmware is 1.10 - go here http://forum.rpc1.org/dl_firmware.php?category=4&manufactor=25 and check it out just incase or for any future firmware updates. One of your drive/driver is in PIO Mode or it's Off. DMA needs to be On. To bring back DMA on, try to troubleshoot as below. ((((( To enable DMA back ON by "uninstalling" it's driver ))))) A) on "DESKTOP" right click on "MY COMPUTER", left click on "PROPERTIES" B) left click on "HARDWARE", left click on "DEVICE MANAGER" C) left click on + sign of DVD/CD-ROM Drives D) double left click on your DVD burner or your dvd-rom drive. NOTE: (do it once at a time and restart once at a time) E) left click on "DRIVER", left click on"UNINSTALL", you will see a "Warning: you are about to uninstall this device from your system", just click "OK", now "SHUTDOWN" or "Restart" your computer F) once you restart your computer, Windows should automatically detect your DVD burner, CD/DVD-ROM, or the Driver you uninstalled and re-install it for you. That's it...easy as smoking!! NOTE: do these steps only if the above process failed to bring DMA back on, or you can do exactly like the above steps, except this time you "uninstall" it from the IDE ATA/ATAPI Controllers. (A) left click on + sign of IDE ATA/ATAPI Controllers (B) double left click on either "Primary or Secondary" IDE Channel (NOTE: you have to know where your "DVD Burner" or "DVD-ROM drive" is installed to what Channel). Usually it's the "Secondary IDE Channel" because your "C: drive or Hard Drive" would be the main aka Primary IDE Channel already. If you're not sure, then you need to check it with "Nero Toolkit" first before you "uninstall" any of them. Once you verify with Nero Toolkit, then you can continue with the next step. (C) click on "DRIVER", "UNINSTALL", "OK" and then "shutdown" or "restart" your computer. That's it... easy as smoking!!! NOTE: To verify your dvd burner/dvd-rom drivers with Nero: Open up "Nero Ultra" or "StartSmart", click on "Nero Toolkit", then click on "Nero InfoTool" (InfoTool will run and retrieve all drivers), now click on "Configuration" - this should show you where your DVD Burner/DVD-ROM is installed under either Primary or Secondary <--- make good note of that and you're ready to "uninstall" your dvd burner/dvd-rom drivers now. Looks like it's a SONY DVD-R (Made In Taiwan) blank here. I recommend you to get the "Made In Japan" blank media next time if you're going to buy SONY again. Perhaps, you might want to try some of these high quality media such as Taiyo Yuden (including both FUJI & SONY "Made In Japan"), MAXELL (a top notch manufactured by HITACHI, "Made In Japan") andVerbatim (id code: MCC003 or MCC004). Below is an example of a successfully completed burning from Nero Burning Rom of mine. As you can see, I backed up "Appleseed" (good action/sci-fi anime movie) and yes... I did write at 8X using Taiyo Yuden, code: YUDEN000-T02 flawlessly. Here it is... just for a look. David X Home Uses 1a23 Windows XP 5.1 IA32 WinAspi: File 'Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 10/26/2004 6:35:34 PM ahead WinASPI: File 'C:\Program Files\Ahead\nero\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 10/26/2004 6:35:34 PM Nero Version: 6.6.0.16 Internal Version: 6, 6, 0, 16b Recorder: <SONY DVD RW DRU-710A> Version: BYX4 - HA 1 TA 0 - 6.6.0.16 Adapter driver: <atapi> HA 1 Drive buffer : 2048kB Bus Type : default (0) -> ATAPI, detected: ATAPI CD-ROM: <TOSHIBA ODD-DVD SD-M1802>Version: 1051 - HA 1 TA 1 - 6.6.0.16 Adapter driver: <atapi> HA 1 === Scsi-Device-Map === DiskPeripheral : ST340014A atapi Port 0 ID 0 DMA: On DiskPeripheral : ST380011A atapi Port 0 ID 1 DMA: On CdRomPeripheral : SONY DVD RW DRU-710A atapi Port 1 ID 0 DMA: On CdRomPeripheral : TOSHIBA ODD-DVD SD-M1802 atapi Port 1 ID 1 DMA: On === CDRom-Device-Map === SONY DVD RW DRU-710A D: CDRom0 TOSHIBA ODD-DVD SD-M1802 E: CDRom1 ======================= AutoRun : 0 Excluded drive IDs: WriteBufferSize: 83886080 (0) Byte ShowDrvBufStat : 0 BUFE : 0 Physical memory : 991MB (1015280kB) Free physical memory: 574MB (588696kB) Memory in use : 42 % Uncached PFiles: 0x0 Use Inquiry : 1 Global Bus Type: default (0) Check supported media : Disabled (0) 1.9.2005 UDF/ISO compilation 10:51:29 PM #1 Phase 112 File dlgbrnst.cpp, Line 1832 DVD-Video files reallocation started 10:51:29 PM #2 Phase 114 File dlgbrnst.cpp, Line 1832 DVD-Video files reallocation completed (no file modified) 10:51:29 PM #3 Text 0 File Isodoc.cpp, Line 6356 UDF document burn settings ------------------------------------------ Determine maximum speed : FALSE Simulate : FALSE Write : TRUE Finalize CD : TRUE Multisession : FALSE Burning mode : DAO Mode : 1 UDF Mode : UDF/ISO bridge UDF Revision : 1.02 UDF Partition Type : physical ISO Level : 1 (Max. of 11 = 8 + 3 char) Character set : ISO 9660 Joliet :FALSE Allow pathdepth more than 8 directories : FALSE Allow more than 255 characters in path : FALSE Write ISO9660 ;1 file extensions : TRUE 10:51:29 PM #4 Phase 111 File dlgbrnst.cpp, Line 1832 DVD-Video files sorted 10:51:29 PM #5 Text 0 File Reader.cpp, Line 127 Reader running 10:51:29 PM #6 Text 0 File Writer.cpp, Line 122 Writer SONY DVD RW DRU-710A running 10:51:29 PM #7 ISO9660GEN -11 File geniso.cpp, Line 3309 First writeable address = 0 (0x00000000) 10:51:29 PM #8 ISO9660GEN -11 File geniso.cpp, Line 3309 First writeable address = 0 (0x00000000) 10:51:29 PM #9 Text 0 File Burncd.cpp, Line 3233 Turn on Disc-At-Once, using DVD media 10:51:29 PM #10 Text 0 File DlgWaitCD.cpp, Line 270 Last possible write address on media: 2295103 (510:01.28, 4482MB) Last address to be written: 2268751 (504:10.01, 4431MB) 10:51:29 PM #11 Text 0 File DlgWaitCD.cpp, Line 282 Write in overburning mode: NO (enabled: CD DVD) 10:51:29 PM #12 Text 0 File DlgWaitCD.cpp, Line 2483 Recorder: SONY DVD RW DRU-710A, Media type: DVD+R Disc Manufacturer ID: YUDEN000, Media Type ID: T02, Product revision number: 0 Disc Application Code: 0, Extended Information Indicators: 3 10:51:29 PM #13 Text 0 File DlgWaitCD.cpp, Line 448 >>> Protocol of DlgWaitCD activities: <<< ========================================= 10:51:29 PM #14 Text 0 File ThreadedTransferInterface.cpp, Line 838 Setup items (after recorder preparation) 0: TRM_DATA_MODE1 () 2 indices, index0 (150) not provided original disc pos #0 + 2268752 (2268752) = #2268752/504:10.2 relocatable, disc pos for caching/writing not required/ required, no patch infos -> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2268752 blocks [SONY DVD RW DRU-710A] -------------------------------------------------------------- 10:51:29 PM #15 Text 0 File ThreadedTransferInterface.cpp, Line 1051 Prepare recorder [SONY DVD RW DRU-710A] for write in CUE-sheet-DAO DAO infos: ========== MCN: "" TOCType: 0x00; Session Closed, disc fixated Tracks 1 to 1: 1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4646404096, ISRC "" DAO layout: =========== __Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________ 0 | lead-in | 0 | 0x41 | 0x00 0 | 1 | 0 | 0x41 | 0x00 0 | 1 | 1 | 0x41 | 0x00 2268752 | lead-out | 1 | 0x41 | 0x00 10:51:29 PM #16 Phase 24 File dlgbrnst.cpp, Line 1832 Caching of files started 10:51:30 PM #17 Text 0 File Burncd.cpp, Line 4120 Cache writing successful. 10:51:30 PM #18 Phase 25 File dlgbrnst.cpp, Line 1832 Caching of files completed 10:51:30 PM #19 Phase 36 File dlgbrnst.cpp, Line 1832 Burn process started at 8x (11,080 KB/s) 10:51:30 PM #20 Text 0 File ThreadedTransferInterface.cpp, Line 2654 Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0 10:51:30 PM #21 Text 0 File Cdrdrv.cpp, Line 8862 ---- DVD Structure: Physical Format Information (00h) ---- Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050 Book Type: DVD+R (10), Part Version: 1.0x (1) Disc Size: 120 mm, Maximum Rate: <not specified> (F h) Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable Linear Density: 0,267 um/bit, Track Density: 0,74 um/track Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW) End Physical Sector Number of Data Area: 26053F h End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB) Data in Burst Cutting Area (BCA) does not exist Disc Application Code: 0 / 0 h Extended Information indicators: 3 h Disc Manufacturer ID: YUDEN000 Media type ID: T02 Product revision number: 0 Number of Physical format information bytes in use in ADIP up to byte 63: 56 Media Specific [16..63]: 00 00 03 59 55 44 45 4E - 30 30 30 54 30 32 00 38 ...YUDEN000T02.8 23 54 37 10 02 4E 72 02 - 8C 63 16 16 0B 0B 0A 0A #T7..Nr..c...... 01 19 1B 0C 0C 0C 0D 01 - 00 00 00 00 00 00 00 00 ................ 10:51:30 PM #22 Text 0 File DVDR.cpp, Line 5618 Drive: SONY DVD RW DRU-710A Book Type request [LO]: DVD-ROM Changing the Book Type was finished successfully, return code 0 10:51:30 PM #23 CDR -1207 File DVDR.cpp, Line 5065 Book Type automatically set to: DVD-ROM 10:51:30 PM #24 Text 0 File DVDPlusRW.cpp, Line 665 Start write address at LBA 0 DVD high compatibility mode: Yes 10:59:18 PM #25 Text 0 File WriterStatus.cpp, Line 116 <SONY DVD RW DRU-710A > start writing Lead-Out at LBA 2268752 (229E50h), lenght 0 blocks 10:59:18 PM #26 Text 0 File ThreadedTransfer.cpp, Line 228 all writers idle, stopping conversion 10:59:47 PM #27 Text 0 File DVDR.cpp, Line 5618 Drive: SONY DVD RW DRU-710A Book Type request [LO]: DVD+R Changing the Book Type was finished successfully, return code 0 10:59:47 PM #28 Phase 37 File dlgbrnst.cpp, Line 1832 Burn process completed successfully at 8x (11,080 KB/s) Existing drivers: File 'Drivers\atapi.sys': Ver=5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), size=95360 bytes, created 8/3/2004 11:59:44 PM (Adapter driver for rec) Registry Keys: HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
