as of now, im a little confused right now =/

Your DMA has slipped into PIO mode,

so what should i do...this looks a lil bit different than what alkohol has posted right?

yeah lol im confused right now

Follow alkohols steps, one by one and you cant go wrong, I will no longer respond to this thread, all answers will be in your other thread

Thanks a lot "alkohol" for that post it helped me out a lot

hi, i am having trouble with dma on my hd and this is the place to get help. there is some great info and tools here but i have not been able to fix it yet. before i start let me explain my situation.

i recently had a raid aray crash and had a problem with the drive size oon one of the drives. it is a hitachi deskstar vlat80. the 200gb drive was reporting as 40gb. i used a dos based f-tool from hitachi and fixed the size. the utility can also change the dma mode and that is set at ata 100.
i install the drive on my main system and dma is not active. i follow the procedure on the first page and i got it to activate, temporarily? i changed the device mode to pio only, remove the drive, restart, turn off and then reinstall. change the mode to dma and it activates :) then go back to check and it is back in pio mode?

i did this a few times with the same result. i try a different drive in the same plug and dma is active? are there any other things i can try? just for giggles i hooked the drive up to a usb controller and the transfer rate was good for a few secconds then it froze up?
please help

i figured out the problem :) the hard drive needed to be erased? not just formated. i did a hard drive sest and it was fine so i figured i could format it and be ok. nope. even though there were no bad sectors there was something wrong.
so, i used the drive utility and erased the drive. makes it like new. it puts all 0's on the drive and takes some time. after that it was fine.

http://www.afterdawn.com/general/adprices.cfm

ok, I guess I posted something to the wrong thread now that I see this here.
I still have a question though, if someone wouldn't mind answering me. I am not certain which of my primary/secondary IDEs belong to my dvd drive.
When I click on Configuration in Nero INfotool this is what I see
-primary ide channel
-Master:WDCWD800BB-00JHA0
-DMA off
-secondary ide channel
-primary ide channel
-secondary ide channel
Master:lite-on combo sohc-4832K
DMA on
Autonrun On
Slave:lite-on DVDRW SHW-160P6S
DMA on
Autorun on
-Sis PCI to USB Enhanced Host controller.

I have a drop down box at the very top and it shows both my drives but, when I change the drive showing, nothing changes in the configuration box itself.
Is it the -primary ide channel -Master:WDCWD800BB-00JHA0 -DMA off that I need to uninstall to fix my "No Disk" problem in my dvd player, but will play in my computer, and teh 75 minutes it took to encode and then write the movie to dvd?
I would welcome any advice.

I Did exactly what the guide said.. the Settings say DMA if available and Nero info tool said DMA is off DOES THIS MATTER?? or should I just leave it alone then

Thanks (Have a Plextor and LG-CDRW)

hey freup,
I would think you would have to find out why Nero is saying your DMA is off if the settings says "Dma if available". The Dma has to be enabled, to my knowledge.

First - BIG thanks to Alkohol for this GREAT instructional guide. My secondary had somehow slipped into PIO mode and my burns went from 10-15 minutes up to 50 MINUTES!!! With this fix I'm back to my previous speed and LOVING IT!!

I vote that this guide be stickyed so everyone who is using Nero can find it and gain the same benefit that I, and many others, have experienced.

Gold Stars to Alkohol, and all the great folks here at Afterdawn that have taken this newbie from a coaster maker to a capable DVD Burner!! Thanks as always!!

Fryerider

@freup

What is your burner listed under what channel? Usually it should be under the Secondary. And no Nero doesn't lie. Can you post up a screenshot? If it still says "DMA is OFF," then you'll need to "uninstall" your driver, restart your system, then let Windows reinstall it for you.

Look at pictures for reference.

@fryerider

You're welcome, glad I could help. Now your back in business, so happy ripping and burning.

Hello Alkohol,
U have become the star of many forums.
And u have made the complicated things very simple.
Coming to my matter,
i would like u to know abt the configuration of my system first of all,
1) 160 gb SATA hdd
2) LG DVD WRITER 16x
3) LG CD WRITER also
4) NVIDIA Graphics card
Till last few days, my DVD burner was very much fine.All the devices were in DMA mode including the hard disk.
Suddenly from the day before,it started burning a DVD for 24 min instead of 8 min while writing in 8x.
When i checked out the reason, the harddisk was not in DMA mode.It showed DMA off in Nero INFO tool.Moreover the system performance is too worst.Its very slow.So i think that the harddisk not being in DMA mode is the major cause behind everything.Right?
So wat do u wan me 2 do Alkohol?how can i turn the hard disk to DMA mode?
How is it possible?
Pls reply to this post.

here follows my Nero LOG FILE TEXT

1A23-serial number removed

Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Ahead\Nero\Wnaspi32.dll': Ver=2.0.1.56, size=163910 bytes, created 4/2/2003 8:43:44 PM
Nero version: 6.0.0.0
Recorder: <HL-DT-ST DVDRAM GSA-4167B>Version: DL10 - HA 0 TA 0 - 6.0.0.0
Adapter driver: <atapi> HA 0
Drive buffer : 2048kB
Bus Type : via Inquiry data (1) -> ATAPI, detected: ATAPI
Connected to MMC as unknown drive with class-nr : 1
Drive is autodetected - recorder class: Std. MMC recorder
CD-ROM: <HL-DT-ST DVDRAM GSA-4167B>Version: DL10 - HA 0 TA 0 - 6.0.0.0
Adapter driver: <atapi> HA 0

=== Scsi-Device-Map ===
CdRomPeripheral : HL-DT-ST DVDRAM GSA-4167B atapi Port 0 ID 0 DMA: On
DiskPeripheral : ST3160023AS atapi Port 1 ID 0 DMA: Off
CdRomPeripheral : HL-DT-ST CD-RW GCE-8526B atapi Port 3 ID 1 DMA: Off
CdRomPeripheral : FvF-Inc CDDVD-2003-200x 0800 FVDSCSI Port 4 ID 0 DMA: ?
=======================

AutoRun : 1
Excluded drive IDs:
CmdQueuing : 1
CmdNotification: 2
WriteBufferSize: 40894464 (0) Byte
ShowDrvBufStat : 0
EraseSpeed : 0
BUFE : 0
Physical memory : 254MB (260844kB)
Free physical memory: 83MB (85712kB)
Memory in use : 67 %
Uncached PFiles: 0x0
Use Static Write Speed Table: 0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)

4.11.2006
CD-ROM (ISO)
9:41:40 AM #1 Text 0 File Isodoc.cpp, Line 5451
Iso document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : FALSE
Multisession : TRUE
Multisession type: : Start multisession
Burning mode : DAO
Mode : 1
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet : TRUE
Allow pathdepth more than 8 directories : TRUE
Allow more than 255 characters in path : TRUE
Write ISO9660 ;1 file extensions : TRUE

9:41:40 AM #2 Text 0 File Reader.cpp, Line 118
Reader running

9:41:40 AM #3 Text 0 File Writer.cpp, Line 127
Writer HL-DT-ST DVDRAM GSA-4167B running

9:41:40 AM #4 ISO9660GEN -11 File geniso.cpp, Line 3814
First writeable address = 0 (0x00000000)

9:41:41 AM #5 Text 0 File Burncd.cpp, Line 3081
Turn on Disc-at-once, using DVD media

9:41:41 AM #6 Text 0 File DlgWaitCD.cpp, Line 224
Last possible write address on media: 2295103 (510:01.28)
Last address to be written: 2171247 (482:29.72)

9:41:41 AM #7 Text 0 File DlgWaitCD.cpp, Line 229
Write in overburning mode: FALSE

9:41:41 AM #8 Text 0 File DlgWaitCD.cpp, Line 1688
Recorder: HL-DT-ST DVDRAM GSA-4167B, Media type: DVD+R
Disc Manufacturer ID: MBIPG101, Media Type ID: R04, Product revision number: 1
Disc Application Code: 0, Extended Information Indicators: 3

9:41:41 AM #9 Text 0 File ThreadedTransferInterface.cpp, Line 757
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 (CTransferItem)
2 indices, index0 (150) not provided
original CD pos #0 + 2171248 (2171248) = #2171248/482:29.73
relocatable, CD pos for caching/writing not required/required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2171248 blocks [HL-DT-ST DVDRAM GSA-4167B]
--------------------------------------------------------------

9:41:41 AM #10 Text 0 File Burncd.cpp, Line 3318
Recorder and media-info

=======================

Burning to HL-DT-ST DVDRAM GSA-4167B on a DVD+R media

9:41:42 AM #11 Text 0 File ThreadedTransferInterface.cpp, Line 910
Prepare recorder HL-DT-ST DVDRAM GSA-4167B for write in cue-sheet-DAO
DAO infos:
==========
MCN:
TOCTYPE: 0x0 Session Closed, CD fixated
Tracks 1 to 1:
TRM_DATA_MODE1, 2048/0x0, ISRC "", FilePos 0 307200 152055808

9:41:43 AM #12 Phase 24 File dlgbrnst.cpp, Line 1818
Caching of files started

9:41:43 AM #13 Phase 25 File dlgbrnst.cpp, Line 1818
Caching of files completed

9:41:43 AM #14 Phase 36 File dlgbrnst.cpp, Line 1818
Burn process started at 8x (11,040 KB/s)

9:41:43 AM #15 Text 0 File ThreadedTransferInterface.cpp, Line 2104
Verifying CD position of item 0 (relocatable, CD pos, no patch infos, orig at #0): write at #0

9:41:43 AM #16 Text 0 File Cdrdrv.cpp, Line 7827
---- DVD Structure: Physical Format Information (00h) ----
Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD+R (10), Part Version: 1
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26053F h
End Sector Number in Layer 0: 0 h
Data in Burst Cutting Area (BCA) does not exist
Media Specific:
00 03 4D 42 49 50 47 31 - 30 31 52 30 34 01 38 23 ..MBIPG101R04.8#
54 37 12 02 42 6E 02 A8 - 6B 15 15 0B 0B 08 08 01 T7..Bn..k.......
19 1B 0C 0C 0C 0D 01 00 - 00 00 00 00 00 00 00 01 ................

9:41:43 AM #17 Text 0 File dlgbrnst.cpp, Line 1678
Set remaining time: 6:52,069 (412069ms) -> OK

9:41:43 AM #18 Text 0 File DVDPlusRW.cpp, Line 513
Start write address at LBA 0
DVD high compatibility mode: Yes

10:05:26 AM #19 Text 0 File WriterStatus.cpp, Line 112
<HL-DT-ST DVDRAM GSA-4167B> start writing Lead-Out at LBA 2171248 (212170h), lenght 0 blocks

10:05:26 AM #20 Text 0 File ThreadedTransfer.cpp, Line 227
all writers idle, stopping conversion

10:05:47 AM #21 Text 0 File dlgbrnst.cpp, Line 1678
Set remaining time: 0:00,000 (0ms) -> OK

10:05:47 AM #22 Text 0 File dlgbrnst.cpp, Line 1678
Set remaining time: 0:00,000 (0ms) -> OK

10:05:47 AM #23 Phase 37 File dlgbrnst.cpp, Line 1818
Burn process completed successfully at 8x (11,040 KB/s)


Existing drivers:
File 'Drivers\PXHELP20.SYS': Ver=2.03.28a, size=20640 bytes, created 3/12/2005 3:58:14 AM (Prassi/Veritas driver for win 2K)
File 'Drivers\atapi.sys': Ver=5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), size=95360 bytes, created 8/3/2004 5:29:44 PM (Adapter driver for rec)

Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)

====== *** Nero-Burning Rom, History File *** ======

@bharatgr8 -

you'd posted your entire Nero logfile, no problem, though i've removed all but the last burn log entry. Also i've edited out your serial number..

Quote:

---

Nero version: 6.0.0.0

---

- Nero's very old, that would be ok apart from the fact that your burner isn't recognised by Nero. See 2 comments down..

Quote:

---

Recorder: <HL-DT-ST DVDRAM GSA-4167B>Version: DL10

---

- burners' firmware is out of date, update to DL13 from here - http://forum.rpc1.org/dl_firmware.php?download_id=2126

Quote:

---

Connected to MMC as unknown drive with class-nr : 1
Drive is autodetected - recorder class: Std. MMC recorder

---

- yup, Nero's too old to recognise your burner, update to 6.6.0.18, the best 6.x version in my opinion - http://httpdl1.usw.nero.com/software/Ner....0.18_no_yt.exe

Quote:

---

DiskPeripheral : ST3160023AS atapi Port 1 ID 0 DMA: Off
CdRomPeripheral : HL-DT-ST CD-RW GCE-8526B atapi Port 3 ID 1 DMA: Off

---

- DMA needs sorting out, hence your joining this thread

Quote:

---

Physical memory : 254MB (260844kB)
Free physical memory: 83MB (85712kB)
Memory in use : 67 %

---

- 512MB is what i consider the minimum for dvd work. you should get more memory, and for now you're gonna have to dig deep to close down as much as you can to free up more memory prior to ALL burning

Quote:

---

Burn process completed successfully at 8x (11,040 KB/s)

---

- hmmm, surprising given the problems that need resolving here

Something to add to creaky's reply,

Quote:

---

Media Specific:
00 03 4D 42 49 50 47 31 - 30 31 52 30 34 01 38 23 ..MBIPG101R04.8#
54 37 12 02 42 6E 02 A8 - 6B 15 15 0B 0B 08 08 01 T7..Bn..k.......
19 1B 0C 0C 0C 0D 01 00 - 00 00 00 00 00 00 00 01 ................

---

That media is very poor. Try better brands such as Verbatim, Sony (Mad in Japan) and Taiyo Yuden.

Creaky didn't post it as, at the moment, it isn't the problem. However, I am one to bitch when people don't use decent media, but trust me, it's for your own good ;-)

I did that (unstalled the driver and window detect it again, but still say DMA is of

hello creaky
I was very pleased for ur wonderful and amazing reply.It was so useful to me.
But U mentioned that DMA is to be sorted out.
So how do u do that?I donno how to sort out the DMA mode.
Pls lemme know how 2 do so.
Thank u for the efforts u have taken to reply me with such a useful and long stuff.
Bye

hello ripper,
i didnt understand ur statement "Try better Brand"
Wat do u mean by this?
R u saying that my LG DVD burner is not a good brand?
Pls lemme know clearly.
Bye

Ok see this guide to turn on DMA
http://my.afterdawn.com/alkohol/blog_entry.cfm/231/dmaissues

And then try better brand means, brand of disks, not the drive itself.

ripper,
the problem is not with the DVD burner or something else.
The only problem is with the SATA harddisk which is in PIO mode.
I tried 2 change it to DMA mode as shown in the guide u provided.
But it again turned to the PIO after the restart.
I checked in Nero INFO tool also.
It says DMA OFF for my Harddisk.
So should i uninstall the SATA hardisk in the DISK DRIVES category in Device Manager? Will that help me?
Its shown in the guide that if the DVD burner dusnt turn to DMA mode even after altering it, then they advised to uninstall the DVD burner itself.
Do i need 2 change the slot of SATA cable once.Mabbe that would work out.One of my cousin has done that and now hes doin fine.There was no problem till date.
So shall i do that?

Ok make sure your HDD is set to master and that your drive is set to master aslo
See this...
http://home.comcast.net/~bbmayo/Jumper%2...our%20Drive.pdf

Get back to me...

Originally posted by bharatgr8:

---

the problem is not with the DVD burner or something else.
The only problem is with the SATA harddisk which is in PIO mode.
I tried 2 change it to DMA mode as shown in the guide u provided.
But it again turned to the PIO after the restart.
I checked in Nero INFO tool also.
It says DMA OFF for my Harddisk.
So should i uninstall the SATA hardisk in the DISK DRIVES category in Device Manager? Will that help me?
Its shown in the guide that if the DVD burner dusnt turn to DMA mode even after altering it, then they advised to uninstall the DVD burner itself.
Do i need 2 change the slot of SATA cable once.Mabbe that would work out.One of my cousin has done that and now hes doin fine.There was no problem till date.
So shall i do that?

---

If you'd already tried to uninstall via its driver and upon restart it still showed PIO or OFF Mode, then it's wise to unplug the cable, wait for 45 seconds, then plug it back on. Then try to restart your system again to see if it has solved the DMA issue.

Hmmm... this maybe irrelevant, but maybe your Nvidia is having issue? Try to search for Nvidia driver via this Nero forum for more help. It has done in the past at this very forum by a few members that they had Nvidia driver and were having DMA issues.