|
How to fix no drive detected with MTKFLASH.exe
|
|
|
chnky18
Member
|
13. April 2007 @ 04:42 |
Link to this message
|
|
after 10 hours and following all the steps, plugging in to a different sata port on the card made all the difference on the ms25 drive :)
|
|
Advertisement
|
 |
|
|
|
athfinder
Newbie
|
14. April 2007 @ 15:06 |
Link to this message
|
|
Hi guys ...i have been on this for many days now i can't make it work ...now i'm stuck because my pc is showing my xbox360 dvd drive in my bios but not showing in my pc or device manager.
I was so p***** off i just bought a new pc so is it a jumper problem because i know nothing about jumpers ...hope it's not
i have onboard sata nvidia nforce 430 sata controller
ms-25 samsung
please help me i really wanna make it work...
|
|
dzqv53
Newbie
|
21. April 2007 @ 10:35 |
Link to this message
|
|
Connects an "IDE" rom to the IDE port of ur PCI card should do the job (thats how i get it to work)
*Note remember which drive to which port before flashing.
*Warning unplug all raid drive before anything (kill my raid array while getting the "no drive detected" problem
|
|
mrleftnut
Newbie
|
19. August 2007 @ 12:07 |
Link to this message
|
Originally posted by coryjb69:
you have to the 10 second trick.
boot from floppy and turn on 360
once you get to the point where you pick which drive to flash turn off the 360 count to exactly 10 and press the button on your pc that goes with the 360 and the power button on the 360 at the same time.
might not work the first try but just keep trying I have done this multiple times with success but sometimes it takes several tries.
dudes a genious! it worked for me first try! when it asked which drive you want to select, turn off the xbox, wait 10 seconds and then press the xbox power at the same time as your drive selection on the keyboard. its the only way i could keep it from freezing at that point.
|
|
ksdankman
Newbie
|
23. August 2007 @ 17:41 |
Link to this message
|
I have an ASUS P4P800 E Deluxe mobo. it has onboard SATA, but when I get to step 5, there are no SATA options for me to hex edit.
when I run the mtkflash utility it says no drives detected. I have disabled RAID and all the IDE as stated by the instructions.
anyone gotten this to work using this mobo?
am I going to have to buy a SATA card to get this to work?
thankful for any help
|
|
insodus
Newbie
|
26. August 2007 @ 20:40 |
Link to this message
|
|
I'm having some problems getting my 360 flashed (its a ms25). I installed a blaster 360, and all went well. After the install I checked and I could still get into the dashboard and play games.
I started up iPrep, selected my new firmware, selected my nForce SATA controller. (its a 650i based mobo) it created my usb stick no problems.
after booting into the usb stick, I constantly got "no drive detected". I tried many suggestions from this thread, nothing worked.
finally I resorted to trying to hex edit mtkflash myself with the values I found in msinfo32.exe.
I did this and when I booted I no longer got "No drive detected" but got a "VIA 6421 Master" and "VIA 6421 Slave". I selected the master and it just hung.
Now I can't get my BIOS to detect the drive anymore and I cant get the xbox to boot period, the start button just flashes red.
I've read that if I get a true VIA vt6421L that I can repair it. Any help please? I really hope I didn't just brick $400.
|
|
ovuka92
Newbie
|
28. August 2007 @ 13:08 |
Link to this message
|
|
I have problems reading my firmware,i tooked my 360 to a sevice and they said the same,i tried to reflash my 360 afther i got the E66,afther installing an update.Service people say that the problem is becouse i have stopped the instalation durring update and now the DVD rom cant be read,and the PC cant read it and they say it cant be fixed,is this true do i need to replace my 360 or is there a way?
Any help would be great!
|
|
justin410
Junior Member
|
6. September 2007 @ 20:22 |
Link to this message
|
|
ok i have a m28 and a vt6421 and tried all these tricks and plus trying it to plug it in at diffrent times and used xtreme bootmaker and iprep the first m28 i flashen never had this problem. the one im trying to flash now hasnt been flashed before and i still cant get it to read the drive ive also hex edited the mtkflash as well.
|
|
s00pcan
Suspended due to non-functional email address
|
8. September 2007 @ 19:05 |
Link to this message
|
http://www.newegg.com/Product/Product.aspx?Item=N82E16815124022
I have this sata card. Works great, only problem is that the plastic part of the sata port I use is broken. Getting the cable to stay attached is getting harder every time. How can I edit it so that the program will look for the dvd drive on the other port?
|
|
namix1
Suspended due to non-functional email address
|
23. September 2007 @ 17:10 |
Link to this message
|
|
I also have had the no drive detected error wile using iprep and xtremeboot maker. I have a SATA hard drive and onboard SATA on my mobo. To recognize my controller I had to leave my hard drive plugged in to be abled to see the xbox drive. So my 2 cents is try that if you have a SATA HD. Just make sure you enter the correct #. DONT FLASH YOUR HD. Hope this helps.
|
|
justin410
Junior Member
|
3. October 2007 @ 14:27 |
Link to this message
|
|
thanx for the reply but i dont have a sata drive hooled to it i got it to read the drive now it just gives that 90 error any ideas ?
|
|
stupidbox
Newbie
|
11. October 2007 @ 21:48 |
Link to this message
|
|
My drive is not detected in the main board setup. and when i plug it in, it doesnt load at all. is there any way i can hack the drive in this situation.
i mean is this normal? should i use hot plug after command prompt?
thanks.
|
|
matt55429
Suspended due to non-functional email address
|
2. November 2007 @ 20:02 |
Link to this message
|
|
After seeing your page have a question
Is there help with this ( Key ) issue where it is Saved old DVD drive or is it on the system ?
Or is this something that you download and see about hooking X Box to computer is this also the 360 ?
if so never hooked to computer
I wish you have some idea
Thanks
chuck M
|
|
Shan2k
Junior Member
|
2. February 2008 @ 23:57 |
Link to this message
|
Originally posted by wabashman:
could some one hex edit this and email it back to me please??
Name VIA VT6421 RAID Controller
Manufacturer VIA Technologies, Inc.
Status OK
PNP Device ID PCI\VEN_1106&DEV_3249&SUBSYS_32491106&REV_50\4&2BE4B97F&0&5030
I/O Port 0x0000BC00-0x0000BC0F
I/O Port 0x0000B800-0x0000B80F
I/O Port 0x0000B400-0x0000B40F
I/O Port 0x0000B000-0x0000B00F
I/O Port 0x0000AC00-0x0000AC1F
I/O Port 0x0000A800-0x0000A8FF
IRQ Channel IRQ 18
Driver c:\windows\system32\drivers\viamraid.sys (5.1.2600.410, 59.25 KB (60,672 bytes), 10/10/2006 4:55 PM)
thanks
chris
I have the exact same one!
This message has been edited since posting. Last time this message was edited on 2. February 2008 @ 23:58
|
|
Advertisement
|
|
|
|
GodMan114
Member
|
3. February 2008 @ 15:24 |
Link to this message
|
Originally posted by Shan2k:
Originally posted by wabashman:
could some one hex edit this and email it back to me please??
Name VIA VT6421 RAID Controller
Manufacturer VIA Technologies, Inc.
Status OK
PNP Device ID PCI\VEN_1106&DEV_3249&SUBSYS_32491106&REV_50\4&2BE4B97F&0&5030
I/O Port 0x0000BC00-0x0000BC0F
I/O Port 0x0000B800-0x0000B80F
I/O Port 0x0000B400-0x0000B40F
I/O Port 0x0000B000-0x0000B00F
I/O Port 0x0000AC00-0x0000AC1F
I/O Port 0x0000A800-0x0000A8FF
IRQ Channel IRQ 18
Driver c:\windows\system32\drivers\viamraid.sys (5.1.2600.410, 59.25 KB (60,672 bytes), 10/10/2006 4:55 PM)
thanks
chris
I have the exact same one!
hehe, i think i do too... but i've no idea what to do with what he needs. not my field of expertise per say...
|
