1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Xbox power button

Discussion in 'Xbox - Hardware boot discussion' started by capo201, Mar 25, 2006.

  1. capo201

    capo201 Guest

    Hi,

    I have a modded Xbox that doesn’t turn on anymore from the power button on the console, the only thing that makes the Xbox turn on is the eject button which loads the original Microsoft Dash, even when it loads the MS DASH there is no way to turn it off because the turn off button doesn’t work, it’s like there is no electrical contact from the power button. I asked the people who modded the Xbox for me and they told me that there’s a specific problem with the motherboard (which is apparently very common) and that it would need to be entirely replaced in order for the power button to work again. They suggested that instead of buying a new motherboard I plug the Xbox in to a power bar and use that instead to turn the Xbox on and off. This method does work, but I was wondering how safe it was for the Xbox to be turned on and off with a power bar rather than the original power button?

    Thanks for your advice.
    Capo
     
    capo201, Mar 25, 2006
    #1
  2. theridges

    theridges Guest

    i dont think them people are right with the answer they gave you if they put a chip in the xbox they must have messed up something while doing it....i will look into it for you...as for turning the xbox on and off is up to you i would just plug it in turn it on with the eject and off by turning off the power bar..
     
    theridges, Mar 25, 2006
    #2
  3. KC36330

    KC36330 Regular member

    Joined:
    Dec 9, 2005
    Messages:
    1,733
    Likes Received:
    0
    Trophy Points:
    46
    which chip do you have? it's possible that the reset/eject bypass wiring is faulty.

    kc
     
    KC36330, Mar 28, 2006
    #3
  4. capo201

    capo201 Guest

    I have an Xecuter2 chip
     
    capo201, Mar 30, 2006
    #4
  5. KC36330

    KC36330 Regular member

    Joined:
    Dec 9, 2005
    Messages:
    1,733
    Likes Received:
    0
    Trophy Points:
    46
    the Xecuter2 didn't incorporate the power/eject button into boot configuration, it's something in your power/eject PCB assembly more likely then the MOBO.

    kc
     
    KC36330, Mar 30, 2006
    #5
  6. capo201

    capo201 Guest

    lately, when I plug the cord into the outlet, the xbox turns on for about 5 seconds and then shuts itself off, I then have to unplug it, wait about 1 minute and then plug it back in and it powers on fine, what is causing this in your opinion?
     
    capo201, Mar 31, 2006
    #6
  7. theridges

    theridges Guest

    my be your power supply or like kc said yor motherboard....
     
    theridges, Mar 31, 2006
    #7
  8. KC36330

    KC36330 Regular member

    Joined:
    Dec 9, 2005
    Messages:
    1,733
    Likes Received:
    0
    Trophy Points:
    46
    my opinion would be the PCB eject/power assembly. if you have a buddy sub one or the other and try it out. (I'd recommend putting your switch assembly in theirs)

    kc
     
    KC36330, Mar 31, 2006
    #8
  9. JRHacker

    JRHacker Member

    Joined:
    Sep 26, 2005
    Messages:
    14
    Likes Received:
    0
    Trophy Points:
    11
    The powering on and off sounds like you got a bad flash Of your BIOS
    the x2 should have a backup bank to boot a secondary BIOS try changing
    the switches. also you should go to xbox-scene.com they have a lot of tutorials that might help you but i think the modder who did you box
    1. screwed up
    2. is full of crap and just wants you to have to buy a new mobo

    any other Qs 3-m4i1 m3 JackRabitHacke{over at}lycos{the dot}com
     
    JRHacker, Mar 31, 2006
    #9

Share This Page