|
How to fix no drive detected with MTKFLASH.exe
|
|
Member
|
23. August 2006 @ 11:13 |
Link to this message
|
|
I see there has been more rising conern on how to flash the samsung correctly with the mtkflash. Many people, as I did, have run into no drive detected, or the PORT MASTER SLAVE (whatever) and nothing happens.
Here is your resolution: Try to flash after each suggestion. Do not do 2, unless you have done 1, and do not do 3 unless you have done 2... and so on. Each step builds on eachother, without doing the previous, you might as well pay me 60 bucks to do it lol
1) Make sure RAID is disabled in your bios. There should be an option somewhere.
2) Keep your xbox connected to your computer, but do not turn it on until you are at the command prompt.
3) Try to run the command mtkflash.exe r /sata /m orig.bin instead (do not use if your sata is onboard... meaning not a pci card) If this is sucessful you'll have to use the command mtkflash.exe w /sata /m xtreme30.bin to flash.
4) If you have anything else in your computer that is SATA, disconnect it (harddrive), except your xbox 360. (keep your sata devices unplugged for the rest of this, once we get mtkflash working, then plug it in and see if it works.
5) Your mtkflash.exe needs editing. If you disconnected your harddrive, plug it back in and go to start>run>"msinfo32.exe" if it brings up microsoft help and support, you're going to have to rename a file to an extension of .nfo and try running it. Now go to components>storage>scsi. and you should see something like this...
Name Serial ATA Controller
Manufacturer
Status OK
PNP Device ID PCI\VEN_2211&DEV_4433&SUBSYS_31491106&REV_80\3&61AAA01&0&78
I/O Port 0x00006655-0x00006662
I/O Port 0x00000000-0x00000003
I/O Port 0x00008877-0x00008884
I/O Port 0x00000000-0x00000003
I/O Port 0x00000000-0x0000000F
I/O Port 0x00000000-0x000000FF
IRQ Channel IRQ 20
Driver c:\windows\system32\drivers\driver.sys (5.1.2600.201, 74.63 KB (76,416 bytes), 5/15/2006 7:00 AM)
Now the bits you are going to have to replace in your mtkflash.exe with hexedit are going to be this "11 22 33 44 55 66 77 88" You're msifo32 will look different, but the numbers in those positions are to be entered into mtkflash in that order.
EXAMPLE
Name Serial ATA Controller
Manufacturer
Status OK PNP
Device ID
PCI\VEN_1106&DEV_3249&SUBSYS_31491106&REV_80\3&61AAA01&0&78
I/O Port 0x0000FD00-0x0000FD07
I/O Port 0x00000000-0x00000003
I/O Port 0x0000F100-0x0000F107
I/O Port 0x00000000-0x00000003
I/O Port 0x00000000-0x0000000F
I/O Port 0x00000000-0x000000FF
IRQ Channel IRQ
20 Driver c:\windows\system32\drivers\driver.sys (5.1.2600.201, 74.63 KB (76,416 bytes), 5/15/2006 7:00 AM)
My string would be 06 11 49 32 00 FD 00 F1 and thats would would have to go into my mtkflash.exe.
Now how to insert it. open up mtkflash.exe with your hexeditor, and hit ctrl+g and goto line "b3d6" and replace what ever is there and whatever follows with 06 11 49 32 00 FD 00 F1. So you will have replaced 8 pairs with your own numbers, all of which start on b3d6 and end at b3dd.
Save and close, put that mtk on your disk, and go flash.
Hope this helps
Now you can flash.
This message has been edited since posting. Last time this message was edited on 24. August 2006 @ 03:49
|
|
Advertisement
|
 |
|
|
Member
|
23. August 2006 @ 20:02 |
Link to this message
|
|
Great work Ronnie, at least now there's a sticky to one of the most asked questions. We just need to get Tweeder's guide and BurningAs info on newsgroups here !
LOL, anyways, Good job man !
Don't Drink and Drive, Don't Benadryl and Type. (So many typos, so little time to hit backspace.)
"BEEN TOO LONG IN FORUMS" LESSON 107: A moderator will notice a "h++p://" address the same as a "http://" address.
Three Steps to being succesful in life:
1-Go to school.
2-Don't use drugs.
3-Read the forum rules!
|
|
TheReturn
Suspended due to non-functional email address
|
25. August 2006 @ 07:25 |
Link to this message
|
|
Good job.
we need more stickied guides like how to flash firmware on Toshiba and Samsung, how to backup games.
THE RETURN
Specialist in mod, hack, crack, download, copy, install, fix, repair game consoles and computers.
Click on the picture below to get files, guides and tutorials for Xbox.
This message has been edited since posting. Last time this message was edited on 26. August 2006 @ 06:58
|
Member
|
25. August 2006 @ 08:40 |
Link to this message
|
|
... nm i miss read your post lol
THANK YOU
This message has been edited since posting. Last time this message was edited on 25. August 2006 @ 08:41
|
|
freax
Newbie
|
27. August 2006 @ 05:09 |
Link to this message
|
|
hi,
My englisch isn't verry well so i hope you understand.
I have just one question. When i'm in promt and i have typed mtkflash r/m backup.bin than i have 2 choices:
1: IDE Pri master
2: IDE Pri Slave
and if i choose 1 than i get the message: Port if0, master/slave: a0
By the way i can't find the word "raid" in my bios, i have phoenix bios.
I hope you can help me
|
|
freax
Newbie
|
27. August 2006 @ 06:29 |
Link to this message
|
|
If i go to msinfo32.exe and i go to scsi i can't see any ata controllers but when i go to IDE there are ata controllers:
Naam Intel(R) 82801G (ICH7 Family) Ultra ATA Storage Controllers - 27DF
Fabrikant Intel
Status OK
PNP-apparaat-ID PCI\VEN_8086&DEV_27DF&SUBSYS_72041462&REV_01\3&2411E6FE&0&F9
I/O-poort 0x0000FB00-0x0000FB0F
Stuurprogramma c:\windows\system32\drivers\pciide.sys (5.1.2600.0 (XPClient.010817-1148), 3,25 kB (3.328 bytes), 6-9-2001 22:14)
Naam Primair IDE-kanaal
Fabrikant (Standaard IDE ATA/ATAPI-controllers)
Status OK
PNP-apparaat-ID PCIIDE\IDECHANNEL\4&1F28D857&0&0
I/O-poort 0x000001F0-0x000001F7
I/O-poort 0x000003F6-0x000003F6
IRQ-kanaal IRQ 14
Stuurprogramma c:\windows\system32\drivers\atapi.sys (5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), 93,13 kB (95.360 bytes), 4-8-2004 0:59)
Naam Intel(R) 82801GB/GR/GH (ICH7 Family) Serial ATA Storage Controller - 27C0
Fabrikant Intel
Status OK
PNP-apparaat-ID PCI\VEN_8086&DEV_27C0&SUBSYS_72041462&REV_01\3&2411E6FE&0&FA
I/O-poort 0x0000FA00-0x0000FA07
I/O-poort 0x0000F900-0x0000F903
I/O-poort 0x0000F800-0x0000F807
I/O-poort 0x0000F700-0x0000F703
I/O-poort 0x0000F600-0x0000F60F
IRQ-kanaal IRQ 19
Stuurprogramma c:\windows\system32\drivers\pciide.sys (5.1.2600.0 (XPClient.010817-1148), 3,25 kB (3.328 bytes), 6-9-2001 22:14)
Naam Primair IDE-kanaal
Fabrikant (Standaard IDE ATA/ATAPI-controllers)
Status OK
PNP-apparaat-ID PCIIDE\IDECHANNEL\4&3927DAEF&0&0
Stuurprogramma c:\windows\system32\drivers\atapi.sys (5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), 93,13 kB (95.360 bytes), 4-8-2004 0:59)
Naam Secundair IDE-kanaal
Fabrikant (Standaard IDE ATA/ATAPI-controllers)
Status OK
PNP-apparaat-ID PCIIDE\IDECHANNEL\4&3927DAEF&0&1
Stuurprogramma c:\windows\system32\drivers\atapi.sys (5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), 93,13 kB (95.360 bytes), 4-8-2004 0:59)
Please help me whit this problem
|
Senior Member
1 product review
|
27. August 2006 @ 07:10 |
Link to this message
|
|
if we get this stickyed we need to have the guide to how to burn and falsh your drive stickyed!
|
Member
|
28. August 2006 @ 03:44 |
Link to this message
|
|
then ask the mod. If your sata cards show up in ide, then you're not going to be able to get your xbox 360 working with mtkflash. Go purchase a via vt6421L card, they're cheap (10 dollars).
|
|
Acolon
Newbie
|
28. August 2006 @ 05:58 |
Link to this message
|
|
Hi i have a similar problem i have a via vt8237 sata chipset on an asus mobo and i have flashed with lots of hassle meaning i have version 2 but am trying to upgrade to v3 but won't detect my drive i have edited mtkflash version 1.83 to suit my chipset info but still drive not detected any help would be appreciated. TIA
|
Member
|
28. August 2006 @ 06:15 |
Link to this message
|
|
you've flashed before? then use that mtkflash
|
|
Acolon
Newbie
|
28. August 2006 @ 08:22 |
Link to this message
|
|
Yeah i did flash before but i kept getting the no drive detected message it was by fluke it read my onboard sata. VT8237 chip. I edited mtkflash as per your tutorial and still get no drive detected. Also i've read a few forums and they seem to suggest that i should get a message asking me to select what channel to use but i do not get that message i usually when it flashed pressed 1 quickly after hitting enter. But that doesn't seem to work. Also i have sata bootrom enabled in the bios could this be the problem?? TIA Ronnie
|
Member
|
28. August 2006 @ 08:29 |
Link to this message
|
|
keep sata enabled, make sure raid is disabled.
if your chip is onboard, type mtkflash r /m orig.bin , try turning your xbox on at boot, or on at command prompt
specific hardware configurations require a different combination of my tips, it takes a lot of tweaking to get it to work.
ie.
i have to turn my xbox on at command prompt, and it only works with mtkflash.exe r /sata /m orig.bin. but thats just me.
|
Member
|
30. August 2006 @ 19:38 |
Link to this message
|
|
Hi ronnie,
Sorry to bother you with this, i know by now you must be going nuts with these questions.
I did what your guide said and it worked perfectly for an onboard sata from one of the PCs at my work, but when i do the same thing for my home pc it just doesnt work. There is no sata or "legacy" setting, as some people call it, i took all IDEs out of the board and still no drive detected. i tried turning on the xbox before turning on pc and then after prompt (that's how it works at work) and it doesn't work.
So sorry, but i must ask for your help. This is what i got (It says RAID but it's the NON-RAID card, just in case):
----------------------------------------------------------------
Name VIA VT6421 RAID Controller
Manufacturer VIA Technologies, Inc.
Status OK
PNP Device ID PCI\VEN_1106&DEV_3249&SUBSYS_32491106&REV_50\3&61AAA01&0&50
I/O Port 0x0000E200-0x0000E20F
I/O Port 0x0000E300-0x0000E30F
I/O Port 0x0000E400-0x0000E40F
I/O Port 0x0000E500-0x0000E50F
I/O Port 0x0000E600-0x0000E61F
I/O Port 0x0000FE00-0x0000FEFF
IRQ Channel IRQ 17
Driver c:\windows\system32\drivers\viamraid.sys (5.1.2600.530, 98.63 KB (100,992 bytes), 5/17/2005 12:09 AM)
----------------------------------------------------------------
I modified the mtkflash with 06 11 49 32 00 e2 00 e4 but it doesn't work. I'm wondering if i did something wrong.
Please help ! thanks !
Don't Drink and Drive, Don't Benadryl and Type. (So many typos, so little time to hit backspace.)
"BEEN TOO LONG IN FORUMS" LESSON 107: A moderator will notice a "h++p://" address the same as a "http://" address.
Three Steps to being succesful in life:
1-Go to school.
2-Don't use drugs.
3-Read the forum rules!
|
|
freax
Newbie
|
31. August 2006 @ 06:32 |
Link to this message
|
|
Hi i'm back again,
I have purchased a "Promise Sata300 TX2Plus/TX4 card" because i couldn't found a Via card here in holland.
Finally my sata showed up in SCSI.
Here are the details:
Naam Windows Promise SATA300 TX4/TX2/779 (tm) IDE Controller
Fabrikant Promise Technology
Status OK
PNP-apparaat-ID PCI\VEN_105A&DEV_3D73&SUBSYS_3D73105A&REV_02\4&1AF1648C&0&00F0
I/O-poort 0x0000EF00-0x0000EF7F
I/O-poort 0x0000EA00-0x0000EAFF
Geheugenadres 0xFDEFF000-0xFDEFFFFF
Geheugenadres 0xFDEC0000-0xFDEDFFFF
IRQ-kanaal IRQ 16
Stuurprogramma c:\windows\system32\drivers\ulsata2.sys ( 1.00.0.31, 122,50 kB (125.440 bytes), 15-2-2005 14:19)
I've edit in mtkflash : A510 733D 00EF 00EA
but when i want to flash my samsung he still says No Device.
I've tried everything but nothing worked.
I'll hope you know what's wrong?!?
Greatings,
|
Member
|
31. August 2006 @ 09:27 |
Link to this message
|
|
that doesn't look like its going to work... you need a compatable pci sata card.
|
|
freax
Newbie
|
31. August 2006 @ 10:01 |
Link to this message
|
|
Is this one not compatible?? OOow...@#%$#^##$ Then i leave it how it is. I will wait for some one who can do it for me. I'll hate this stupid $#%#@$#Box (or myself :D)
This message has been edited since posting. Last time this message was edited on 31. August 2006 @ 10:06
|
|
freax
Newbie
|
31. August 2006 @ 10:04 |
Link to this message
|
|
How could you see it isn't compatable?
|
Member
|
1. September 2006 @ 13:29 |
Link to this message
|
|
hi all Genius!!!
i have the same problem as freax had like..
ending up with
after i press 1
port 170: master/slave :a0
wat can be done?
|
|
adfrog10
Suspended due to non-functional email address
|
5. September 2006 @ 08:23 |
Link to this message
|
|
i get port: 1f0 master/slave b0
am i doing it right i have a syntax motherboard how do i turn off the hdd
the frogster is in the house
|
|
adfrog10
Suspended due to non-functional email address
|
5. September 2006 @ 09:24 |
Link to this message
|
|
this is what i get now drive scanned
1:ide pri slave
2:ich5 sec master
3:ich5 sec slave
i get port: 1f0, master/slave:b0
on 1 and 3 and when i click 2 i getdata error reading drive a
the frogster is in the house
|
|
Acolon
Newbie
|
5. September 2006 @ 10:18 |
Link to this message
|
|
I had same problem with onboard sata got the port crap. What i did was in bios if your sata bootrom is enabled disable it sounds odd but it worked on my asus with a via8237 sata chipset. Left xbox disconnected from the pc and boot to the dos disk typed in mtkflash w /m x32.bin powered on 360 waited 10 seconds hit enter the as the disk floppy was seeking i put the sata connector onto the mast port on the board got the menu asking for master or slave selected master and bob's your uncle. I will point out that at no stage did i get the men asking to select what port i wanted before i did this. Hope this is a help.
|
|
adfrog10
Suspended due to non-functional email address
|
5. September 2006 @ 10:58 |
Link to this message
|
|
now i get error flash type: "SST(SST39SF020)"
am i doing it right i turned on sata only master so the only thing it detects is the rom drive do i connect it to the rom drive or the xbox cause i have it connected to the dvd rom drive
the frogster is in the house
|
Member
|
5. September 2006 @ 13:03 |
Link to this message
|
|
hi all...
I use a IDE to Sata converter (it gas just one sata port)
now when i boot my pc with the sata connected to the xbox it does detect the (samsung) dvd rom as it shows on the boot page..
but when try to mtkflash then i get the message
port 170 :master/slave :a0
-
my qustion is ..is it neccessary for the flash to work as the sata detected the dvd rom...???
or its sometimes not campatible even after detecting he dvd rom???
someone...where r all the Genius gone?? it been a week guyz help me someway...
|
Member
|
7. September 2006 @ 08:47 |
Link to this message
|
|
error: fail to open input file
pls someone help me from hear i think i am close..
anyone....??
|
|
Advertisement
|
|
|
|
Tag2006
Member
|
17. September 2006 @ 12:32 |
Link to this message
|
|
Thanks for this post,
In conjuction with this and one on Xboxhacker my problem of drive not detected was due to my sata adaptor being onboard and ran by an IDE controller...with an Nforce 410 chip on an ASROCK board.
The modified mtkflash says its compatable with the 410 chip but I think it must have been set on another motherboard as it did not work for me untill I did step 5 above and put my data in via the hex editor.
So Step 5 fixed it for me.
Thanks Ronnie ;-)
|
