i have just setup the box got all the channels but most are coming up as bad or scrambled channels cannot find menu for emu on off key system details are The Box PVR dual record pvr E_Ver 4.500, 6 jul 2007

Go to parental control in receiver menu

press ( i or info button) + (2007)

key and emu buttons should now be visible
switch key emu to on position
go to scrambled channel and wait for update .

Cheers mate worked a treat. Also can you tell me if my box is a clone or not it has 2 sets of 14 slits going down and 2 slits of 4 going across.

Your fine the PVR hasnt been cloned.

good to know thanks sc0user you know your stuff

Youre welcome, anytime :)

One more problem every time i record one channel and try to watch another i get the info message no signal ! ( T2 )

Have you made sure your loop through cable is plugged into cable tuner 1 output and then to cable tuner 2 input.

i think i had to reboot ie switch on and off. can you watch a program that is being recorded?

can somebody help why cant i watch any of the recordings whilst they are being recorded and the hdd button on the rcu does not work while a program is being recorded

These are just firmware issues that need to be resolved. What side of the TV does the red dot come up on when recording?

Originally posted by mo5afda:

---

can somebody help why cant i watch any of the recordings whilst they are being recorded and the hdd button on the rcu does not work while a program is being recorded

---

Hi
You should be able to record two channels at once and still move channels with the remote control, but you need a short cable between tuner one output and tuner two input like sc0user said. Whilst recording you should also be able to bring up info at top of screen about what is being recorded by pressing the info button on the remote. Tuner one will show at top right what is being recorded and tuner two will show at top left. The hdd button does not opperate while recoring is ongoing, nor the epg button. I am using version 4.5 - 6th July and it is working great.
jbvid

cheers all it took its time but alls running well now. thanx

DOnt know if this is a daft question or not.

But is there any types of specifications hard drive i buy must have to be compatible with box, i.e IDE or SATA etc.

Seen a couple of external HD's but dont want to rush out buy one and dont work because need to have a certain thing.

Originally posted by Scotty78:

---

DOnt know if this is a daft question or not.

But is there any types of specifications hard drive i buy must have to be compatible with box, i.e IDE or SATA etc.

Seen a couple of external HD's but dont want to rush out buy one and dont work because need to have a certain thing.

---

Hi
Can't use an internal or external hard drive with standard The Box.
You don't say if you have The Box PVR or standard The Box. If PVR you need an(Internal)IDE type (7200rpm) to fit onto the IDE ribbon connecter inside The Box PVR. There is also a standard power connector inside the box (PC Type)and a standard fitting bracket to take the drive. When fitted format it by going to Menu/HDD Interface/Format. jbvid

Sorry didnt say what typ of box as just took it this thread was for the pvr twin tuner box's.

Thanks for info also as wasnt sure if it would be external via the USB.

Cheers
Scott

Originally posted by Scotty78:

---

Sorry didnt say what typ of box as just took it this thread was for the pvr twin tuner box's.

Thanks for info also as wasnt sure if it would be external via the USB.

Cheers
Scott

---

Hi
Not sure about external drive through usb but would be a good alternative if it would work. Think it would need firmware mod.
jbvid

can anybody help got a starview pvr and want to install hardrive how do u do it its an internal one

@speedy14
Hi
You will find it is very easy.First disconnect power lead and remove top case, 2 screws at side and 1 at rear.
Then remove the hard drive frame from inside the box. Make sure your H/D has its jumper pin set to master and fit it into the hard drive frame with 4 short screws. Fit the assembly back into the box and connect up the 40 pin IDE cable and power cable (already loose inside the box). Refit top case. Connect everything up and start the box. Press Menu on remote then down to HDD Interface then Format, and wait until formattted, Thats it.
jbvid

Thank you for the advice of the loop which has solved so much for me but not all, but im taking wild guess could still be a firmware issue maybe?

I know can record and watch certain channels, like i tried recording Sky sports 2 but cant watch any other premium like sky sports 1, setanta 1 channels but i can watch free to air channels like e4 itv etc while recording.

Although going to leave it the now and try again after work tomorrow. Getting a little more every little time i try something else lol.

But just to mainly say thanks as wouldve been there for weeks without adding cable between output 1 and input 2.

Hi again

I have just recieved the box pvr and i need to turn on the emu to descramble the channels. When i press the i button and 2007 on the remote to access the hidden menu there is no emu option to turn on and off. Why is it not there?

I just installed my 250gb hard drive which was pretty simple. I still dont have the option to turn on the emu though in the hidden menu so most of my channels are scrambled. Any ideas anyone?

Originally posted by funboyste:

---

I just installed my 250gb hard drive which was pretty simple. I still dont have the option to turn on the emu though in the hidden menu so most of my channels are scrambled. Any ideas anyone?

---

Hi
There is NO option to turn the emu on the PVR Version, only Autoupdate on. Goto Menu/SystemSetup/Press the OK button when Parental Control is highlighted, then press i then press 2007, you should then be in the 'Cas System' Menu, If not in the Cas menu you are not doing it right, start again. All you have to do when in the Cas menu is make sure the Autoupdate Option is On,(Bottom item) Thats all. I presume you have a late version of the firmware installed as I haven't read all the thread again. If you are still struggling get back with your firmware version with (Menu/System Setup/System Information, this will tell you.
jbvid

Thanks for replying, the auto update was already on. The firmware version was version 4.5 (6 Jul 2007). I wentinto Nagravision and it said NTL, so I changed it to TW which is what I scanned it on. I then went to a subscription channel, it said updating info for about a minute and now I have all the channels. That turning on the emu would have been baffling me for a long time. I was thinking I had to load some software or firmware to the box or something. Thanks for helping. Something else what is bugging me right now is that the picture on the tv doesnt fill the screen. On the normal version of 'the box' you just press the blue button to fix it, but I dont know how to fix this with the pvr version.

Hi
Goto Menu/User Setup and play with Aspect Ratio and Display mode, If this fails try similar screen option changes on your TV. I seem to recall having it before on one or two channs but it went away.I am also on TW
jbvid