1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

"command sequence error" and "logical block address out of range"

Discussion in 'DVD±R for advanced users' started by reefis, Feb 22, 2007.

  1. reefis

    reefis Member

    Joined:
    Feb 22, 2007
    Messages:
    11
    Likes Received:
    0
    Trophy Points:
    11
    Hello,
    for at least two years I've had no problems burning dvd's and cd's on my internal Memorex 16+/-DL4RWID2 using Nero. Just the past week I've been getting "pma update failure" when trying to burn cds. with dvd's i get "command sequence error". I did disk cleanup, defrags, updated the firmware. Somehow i can burn cd's again, if i burn at 24x. but still no luck with dvds. I downloaded Cheetah DVD burner to see if it's a problem with Nero, and I got "logical block address out of range" Basically, if you listen to the burner, it seems to be having trouble getting started in the burning process. it seems to be stalling out. you'll hear it rev up for a few seconds and then it stops. eventually it kicks in and seems to be working fine, but after 2 minutes I get the failure messages.. I've tried different media. I just bought a Memorex 50 pack (seems like it'd be very compatible with a memorex burner) and wasn't having any luck with those, so I found a blank Sony disc. IT IS NOT A MEDIA ISSUE. I've tried burning data dvd, video dvds, nothing works at any speeds.. I've wasted at least 15 dvds thus far. Everything was working fine a month ago. I havn't found any helpful info anywheres on the internet. Does anyone have any suggestions? here is my log...
    bubba



    Windows XP 5.1
    IA32
    WinAspi: File 'Wnaspi32.dll': Ver=4.71 (0002), size=45056 bytes, created 11/21/2005 12:48:21 AM
    ahead WinASPI: File 'C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 12:54:32 PM

    NT-SPTI used
    Nero Version: 7.0.0.0 (Nero Express)
    Recorder: <Memorex DVD16+/-DL4RWlD2>Version: JWS6 - HA 1 TA 5 - 7.0.0.0
    Adapter driver: <IDE> HA 1
    Drive buffer : 2048kB
    Bus Type : default (0) -> ATAPI, detected: ?
    CD-ROM: <HL-DT-ST DVD-ROM GDR8163B>Version: 0D20 - HA 1 TA 0 - 7.0.0.0
    Adapter driver: <IDE> HA 1

    === Scsi-Device-Map ===
    DiskPeripheral : WDC WD1600JB-75GVA0 atapi Port 0 ID 0 DMA: On
    CdRomPeripheral : HL-DT-ST DVD-ROM GDR8163B atapi Port 1 ID 0 DMA: Off
    CdRomPeripheral : Memorex DVD16+/-DL4RWlD2 atapi Port 1 ID 1 DMA: Off
    CdRomPeripheral : Generic DVD-ROM 1.0 d347prt Port 2 ID 0 DMA: Off

    === CDRom-Device-Map ===
    HL-DT-ST DVD-ROM GDR8163B D: CDRom0
    Generic DVD-ROM E: CDRom2
    Memorex DVD16+/-DL4RWlD2 F: CDRom5
    =======================

    AutoRun : 1
    Excluded drive IDs:
    WriteBufferSize: 74448896 (0) Byte
    ShowDrvBufStat : 0
    BUFE : 0
    Physical memory : 509MB (522224kB)
    Free physical memory: 206MB (211036kB)
    Memory in use : 59 %
    Uncached PFiles: 0x0
    Use Inquiry : 1
    Global Bus Type: default (0)
    Check supported media : Disabled (0)

    22.2.2007
    ISO compilation
    11:32:46 AM #1 Text 0 File Isodoc.cpp, Line 6410
    Iso document burn settings
    ------------------------------------------
    Determine maximum speed : FALSE
    Simulate : FALSE
    Write : TRUE
    Finalize CD : TRUE
    Multisession : FALSE
    Burning mode : DAO
    Mode : 1
    ISO Level : 1 (Max. of 11 = 8 + 3 char)
    Character set : ISO 9660
    Joliet : TRUE
    Allow pathdepth more than 8 directories : TRUE
    Allow more than 255 characters in path : TRUE
    Write ISO9660 ;1 file extensions : TRUE

    11:32:47 AM #2 Text 0 File ThreadedTransfer.cpp, Line 525
    ReadBuffer-Pipe got 72704KB of Memory

    11:32:47 AM #3 Text 0 File Reader.cpp, Line 124
    Reader running

    11:32:47 AM #4 Text 0 File Writer.cpp, Line 113
    Writer F: Memorex DVD16+/-DL4RWlD2 running

    11:32:47 AM #5 ISO9660GEN -11 File Geniso.cpp, Line 3304
    First writeable address = 0 (0x00000000)

    11:32:47 AM #6 Text 0 File Burncd.cpp, Line 3301
    Turn on Disc-At-Once, using DVD media

    11:32:47 AM #7 Text 0 File DlgWaitCD.cpp, Line 277
    Last possible write address on media: 2298495 (510:46.45, 4489MB)
    Last address to be written: 1976991 (439:19.66, 3861MB)

    11:32:47 AM #8 Text 0 File DlgWaitCD.cpp, Line 289
    Write in overburning mode: NO (enabled: CD)

    11:32:47 AM #9 Text 0 File DlgWaitCD.cpp, Line 2568
    Recorder: Memorex DVD16+/-DL4RWlD2, Media type: DVD-R
    Disc Manufacturer: CMC MA - G. AM3
    Disc Application Code: 64, Disc Physical Code: 193

    11:32:47 AM #10 Text 0 File DlgWaitCD.cpp, Line 456
    >>> Protocol of DlgWaitCD activities: <<<
    =========================================

    11:32:47 AM #11 Text 0 File ThreadedTransferInterface.cpp, Line 846
    Setup items (after recorder preparation)
    0: TRM_DATA_MODE1 ()
    2 indices, index0 (150) not provided
    original disc pos #0 + 1976992 (1976992) = #1976992/439:19.67
    relocatable, disc pos for caching/writing not required/ required, no patch infos
    -> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 1976992 blocks [F: Memorex DVD16+/-DL4RWlD2]
    --------------------------------------------------------------

    11:32:47 AM #12 Text 0 File ThreadedTransferInterface.cpp, Line 1058
    Prepare recorder [F: Memorex DVD16+/-DL4RWlD2] for write in CUE-sheet-DAO
    DAO infos:
    ==========
    MCN: ""
    TOCType: 0x00; Session Closed, disc fixated
    Tracks 1 to 1:
    1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4048879616, ISRC ""
    DAO layout:
    ===========
    __Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
    0 | lead-in | 0 | 0x41 | 0x00
    0 | 1 | 0 | 0x41 | 0x00
    0 | 1 | 1 | 0x41 | 0x00
    1976992 | lead-out | 1 | 0x41 | 0x00

    11:32:47 AM #13 Text 0 File SCSIPassThrough.cpp, Line 34
    SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME

    11:32:47 AM #14 Phase 24 File dlgbrnst.cpp, Line 1724
    Caching of files started

    11:32:47 AM #15 Text 0 File Burncd.cpp, Line 4129
    Cache writing successful.

    11:32:47 AM #16 Phase 25 File dlgbrnst.cpp, Line 1724
    Caching of files completed

    11:32:47 AM #17 Phase 36 File dlgbrnst.cpp, Line 1724
    Burn process started at 6x (8,310 KB/s)

    11:32:47 AM #18 Text 0 File ThreadedTransferInterface.cpp, Line 2669
    Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

    11:32:47 AM #19 Text 0 File DVDR.cpp, Line 2469
    Recording mode: Sequential Recording Mode

    11:32:47 AM #20 Text 0 File MMC.cpp, Line 21541
    Set BUFE: Buffer underrun protection -> ON , Adapt writespeed to disc : ON

    11:32:47 AM #21 Text 0 File DVDR.cpp, Line 2624
    Start write address at LBA 0
    DVD high compatibility mode: Yes

    11:32:47 AM #22 Text 0 File Cdrdrv.cpp, Line 8385
    ---- DVD Structure: Physical Format Information (00h) ----
    Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
    Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 2.1 (33)
    Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
    Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
    Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
    Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
    End Physical Sector Number of Data Area: 0 h
    End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
    Data in Burst Cutting Area (BCA) does not exist
    Start sector number of the current Border-Out: 0 h
    Start sector number of the next Border-In: 0 h
    Media Specific [16..63]:
    00 60 00 10 20 30 40 50 - 00 00 00 21 00 00 00 00 .`...0@P...!....
    00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
    00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................

    11:33:41 AM #23 Text 0 File Cdrdrv.cpp, Line 1195
    11:33:41.031 - F: Memorex DVD16+/-DL4RWlD2 : Queue again later

    11:34:45 AM #24 SPTI -600 File SCSIPassThrough.cpp, Line 306
    CdRom5: SCSIStatus(x00) WinError(121) NeroError(-600)
    Sense Key: 0x00 (KEY_NO_SENSE)
    Sense Code: 0x00
    Sense Qual: 0x00
    CDB Data: 0x5C 00 00 00 00 00 00 00 0C 00 00 00
    Sense Area: 0x00 00 00 00 00 00 00 00 00 00 00 00 00
    Buffer x03e69400: Len xc

    11:36:09 AM #25 SPTI -1114 File SCSIPassThrough.cpp, Line 306
    CdRom5: SCSIStatus(x02) WinError(0) NeroError(-1114)
    Sense Key: 0x06 (KEY_UNIT_ATTENTION)
    Sense Code: 0x29
    Sense Qual: 0x00
    CDB Data: 0x5C 00 00 00 00 00 00 00 0C 00 00 00
    Sense Area: 0x70 00 06 00 00 00 00 0A 00 00 00 00 29
    Buffer x03e69400: Len xc

    11:36:09 AM #26 SPTI -1023 File SCSIPassThrough.cpp, Line 306
    CdRom5: SCSIStatus(x02) WinError(0) NeroError(-1023)
    Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
    Sense Code: 0x2C
    Sense Qual: 0x00
    CDB Data: 0x2A 00 00 00 04 A0 00 00 20 00 00 00
    Sense Area: 0x70 00 05 00 00 00 00 0A 00 00 00 00 2C
    Buffer x03840000: Len x10000
    0x4A 92 51 49 08 06 A3 C6 B3 79 C3 73 BD 3C A7 7B
    0xE0 AB 86 18 EE E2 0A EE D3 E9 5B F5 F8 63 BE ED
    0x70 15 33 26 40 58 ED 13 F7 1E 86 BA 5E 75 96 79

    11:36:09 AM #27 CDR -1023 File Writer.cpp, Line 302
    Command sequence error
    F: Memorex DVD16+/-DL4RWlD2

    11:36:09 AM #28 Text 0 File ThreadedTransfer.cpp, Line 228
    all writers idle, stopping conversion

    11:36:10 AM #29 Text 0 File ThreadedTransfer.cpp, Line 222
    conversion idle, stopping reader

    11:36:10 AM #30 Text 0 File DVDR.cpp, Line 2866
    EndDAO: Last written address was 1183

    11:36:10 AM #31 Phase 38 File dlgbrnst.cpp, Line 1724
    Burn process failed at 6x (8,310 KB/s)


    Existing drivers:
    File 'Drivers\ADPU160M.SYS': Ver=v3.60a (Lab01_N(johnstra).010529-2218), size=101888 bytes, created 8/17/2001 3:07:32 PM
    File 'Drivers\CDRALW2K.SYS': Ver=8.0.0.212 , size=2560 bytes, created 5/19/2006 4:16:24 PM
    File 'Drivers\ASPI32.SYS': Ver=4.71 (0002) built by: WinDDK, size=16512 bytes, created 11/21/2005 12:48:21 AM
    File 'Drivers\PXHELP20.SYS': Ver=3.00.11B, size=46080 bytes, created 5/16/2006 3:23:54 PM (Prassi/Veritas driver for win 2K)

    Registry Keys:
    HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
     
    Last edited: Feb 22, 2007
  2. binkie7

    binkie7 Moderator Staff Member

    Joined:
    Feb 12, 2005
    Messages:
    18,496
    Likes Received:
    0
    Trophy Points:
    116
    Hi reefis
    1st thing edit out the serial # is the log. At the top and begins w/ 1C.

    CdRomPeripheral : HL-DT-ST DVD-ROM GDR8163B atapi Port 1 ID 0 DMA: Off
    CdRomPeripheral : Memorex DVD16+/-DL4RWlD2 atapi Port 1 ID 1 DMA: Off

    Turn DMA back on for these drives. Here's a guide - link

    Nero Version: 7.0.0.0
    Nero can use an update - latest is 7.7.5.1 - may not be part of this problem but several fixes and enhancements since the version you have.

    The Memorex you have were made by CMC - not the best but turn DMA back for the drive and see how that goes.

    File 'Drivers\CDRALW2K.SYS'
    Roxio & Nero don't always play well. If still failing may want to try uninstalling Roxio and run the zap tool to remove it all.
     
  3. reefis

    reefis Member

    Joined:
    Feb 22, 2007
    Messages:
    11
    Likes Received:
    0
    Trophy Points:
    11
    thanks for the help. much appreciated
    i changed the dma. for some reason, since my burner is a slave drive, dma cannot be turned on, or isn't available. I believe this has always been the case, it's just causes a slower burn. (correct?) it seems very odd that when the burner starts the job is stalls (starts briefly and then stops) at least 4 different times before starting up and stopping after 2 or 3 minutes.. I thought maybe it could be a problem with windows media connect taking up too much memory, so i uninstalled that and then nothing... i'm am trying to figure out if CDRALW2K.SYS' has anything to do with it.
     
  4. binkie7

    binkie7 Moderator Staff Member

    Joined:
    Feb 12, 2005
    Messages:
    18,496
    Likes Received:
    0
    Trophy Points:
    116
    How about the DVD-Rom drive - were you able to turn DMA on for that one?

    Since your hard drive is in DMA - as faster data transfer rate then the slow PIO mode it could cause problems & failures. Slowness being one of them.

    Manually change transfer mode in the drop down to 'dma if available' for each one in the seconardy channel then uninstall the ide channel again and reboot.
    You mighthave a bad ide cable & that might be the reason for staying in PIO and possibly the burn failures.

    For the Roxio if you've had in installed all this time then it may not be the problem.
    Might want to rule it out anyhow but need to get the drive back in DMA mode too.

    Oh and you're welcome!
     
  5. reefis

    reefis Member

    Joined:
    Feb 22, 2007
    Messages:
    11
    Likes Received:
    0
    Trophy Points:
    11
    yes, i WAS able to turn DMA on for my dvd-rom drive. I'll open up my computer tommorow and see what's up, I might as well make my burner my master anyway. Do wires ever unattach or burnout?
     
  6. binkie7

    binkie7 Moderator Staff Member

    Joined:
    Feb 12, 2005
    Messages:
    18,496
    Likes Received:
    0
    Trophy Points:
    116
    They can - unfortunately nothing lasts forever :)

    But switch it to master & see how that goes- change the jumper pins on the back of the drives too - dvd-rom will now be set to slave & burner to master.

    Keep us posted!
     
  7. reefis

    reefis Member

    Joined:
    Feb 22, 2007
    Messages:
    11
    Likes Received:
    0
    Trophy Points:
    11
    hello, i did the latter, and turned dma on. I think it IS A MEDIA issue because I got a successful burn with a Sony dvd-r at 6x. with the crappy memorex branded dvd-r it failed again. (this time i had a "reset error" ?). here's the log for that specific burn if you can find anything else fishy. I noticed that my buffer size is only 2 mb. that doesn't seem right to me. is it?

    Windows XP 5.1
    IA32
    WinAspi: File 'Wnaspi32.dll': Ver=4.71 (0002), size=45056 bytes, created 7/17/2002 9:20:56 AM
    ahead WinASPI: File 'C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 12:54:32 PM

    NT-SPTI used
    Nero Version: 7.0.0.0 (Nero Express)
    Recorder: <Memorex DVD16+/-DL4RWlD2>Version: JWS6 - HA 1 TA 3 - 7.0.0.0
    Adapter driver: <IDE> HA 1
    Drive buffer : 2048kB
    Bus Type : default (0) -> ATAPI, detected: ?
    CD-ROM: <Generic DVD-ROM >Version: 1.0 - HA 1 TA 1 - 7.0.0.0
    Adapter driver: <SCSI> HA 1

    === Scsi-Device-Map ===
    DiskPeripheral : WDC WD1600JB-75GVA0 atapi Port 0 ID 0 DMA: On
    CdRomPeripheral : Memorex DVD16+/-DL4RWlD2 atapi Port 1 ID 0 DMA: On
    CdRomPeripheral : Generic DVD-ROM 1.0 d347prt Port 2 ID 0 DMA: Off

    === CDRom-Device-Map ===
    Memorex DVD16+/-DL4RWlD2 D: CDRom3
    Generic DVD-ROM E: CDRom1
    =======================

    AutoRun : 1
    Excluded drive IDs:
    WriteBufferSize: 83886080 (83886080) Byte
    ShowDrvBufStat : 0
    BUFE : 0
    Physical memory : 509MB (522224kB)
    Free physical memory: 153MB (157108kB)
    Memory in use : 69 %
    Uncached PFiles: 0x0
    Use Inquiry : 1
    Global Bus Type: default (0)
    Check supported media : Disabled (0)

    28.2.2007
    ISO compilation
    10:38:02 AM #1 Text 0 File Isodoc.cpp, Line 6410
    Iso document burn settings
    ------------------------------------------
    Determine maximum speed : FALSE
    Simulate : FALSE
    Write : TRUE
    Finalize CD : TRUE
    Multisession : FALSE
    Burning mode : DAO
    Mode : 1
    ISO Level : 1 (Max. of 11 = 8 + 3 char)
    Character set : ISO 9660
    Joliet : TRUE
    Allow pathdepth more than 8 directories : TRUE
    Allow more than 255 characters in path : TRUE
    Write ISO9660 ;1 file extensions : TRUE

    10:38:02 AM #2 Text 0 File ThreadedTransfer.cpp, Line 525
    ReadBuffer-Pipe got 81920KB of Memory

    10:38:02 AM #3 Text 0 File Reader.cpp, Line 124
    Reader running

    10:38:02 AM #4 Text 0 File Writer.cpp, Line 113
    Writer D: Memorex DVD16+/-DL4RWlD2 running

    10:38:02 AM #5 ISO9660GEN -11 File Geniso.cpp, Line 3304
    First writeable address = 0 (0x00000000)

    10:38:02 AM #6 Text 0 File Burncd.cpp, Line 3301
    Turn on Disc-At-Once, using DVD media

    10:38:02 AM #7 Text 0 File DlgWaitCD.cpp, Line 277
    Last possible write address on media: 2298495 (510:46.45, 4489MB)
    Last address to be written: 2235903 (496:52.03, 4366MB)

    10:38:02 AM #8 Text 0 File DlgWaitCD.cpp, Line 289
    Write in overburning mode: NO

    10:38:02 AM #9 Text 0 File DlgWaitCD.cpp, Line 2568
    Recorder: Memorex DVD16+/-DL4RWlD2, Media type: DVD-R
    Disc Manufacturer: CMC MA - G. AM3
    Disc Application Code: 64, Disc Physical Code: 193

    10:38:02 AM #10 Text 0 File DlgWaitCD.cpp, Line 456
    >>> Protocol of DlgWaitCD activities: <<<
    =========================================

    10:38:02 AM #11 Text 0 File ThreadedTransferInterface.cpp, Line 846
    Setup items (after recorder preparation)
    0: TRM_DATA_MODE1 ()
    2 indices, index0 (150) not provided
    original disc pos #0 + 2235904 (2235904) = #2235904/496:52.4
    relocatable, disc pos for caching/writing not required/ required, no patch infos
    -> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2235904 blocks [D: Memorex DVD16+/-DL4RWlD2]
    --------------------------------------------------------------

    10:38:02 AM #12 Text 0 File ThreadedTransferInterface.cpp, Line 1058
    Prepare recorder [D: Memorex DVD16+/-DL4RWlD2] for write in CUE-sheet-DAO
    DAO infos:
    ==========
    MCN: ""
    TOCType: 0x00; Session Closed, disc fixated
    Tracks 1 to 1:
    1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4579131392, ISRC ""
    DAO layout:
    ===========
    __Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
    0 | lead-in | 0 | 0x41 | 0x00
    0 | 1 | 0 | 0x41 | 0x00
    0 | 1 | 1 | 0x41 | 0x00
    2235904 | lead-out | 1 | 0x41 | 0x00

    10:38:02 AM #13 Text 0 File SCSIPassThrough.cpp, Line 34
    SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME

    10:38:03 AM #14 Phase 24 File dlgbrnst.cpp, Line 1724
    Caching of files started

    10:38:03 AM #15 Text 0 File Burncd.cpp, Line 4129
    Cache writing successful.

    10:38:03 AM #16 Phase 25 File dlgbrnst.cpp, Line 1724
    Caching of files completed

    10:38:03 AM #17 Phase 36 File dlgbrnst.cpp, Line 1724
    Burn process started at 6x (8,310 KB/s)

    10:38:03 AM #18 Text 0 File ThreadedTransferInterface.cpp, Line 2669
    Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

    10:38:03 AM #19 Text 0 File DVDR.cpp, Line 2469
    Recording mode: Sequential Recording Mode

    10:38:03 AM #20 Text 0 File MMC.cpp, Line 21541
    Set BUFE: Buffer underrun protection -> ON , Adapt writespeed to disc : ON

    10:38:03 AM #21 Text 0 File DVDR.cpp, Line 2624
    Start write address at LBA 0
    DVD high compatibility mode: Yes

    10:38:03 AM #22 Text 0 File Cdrdrv.cpp, Line 8385
    ---- DVD Structure: Physical Format Information (00h) ----
    Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
    Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 2.1 (33)
    Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
    Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
    Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
    Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
    End Physical Sector Number of Data Area: 0 h
    End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
    Data in Burst Cutting Area (BCA) does not exist
    Start sector number of the current Border-Out: 0 h
    Start sector number of the next Border-In: 0 h
    Media Specific [16..63]:
    00 60 00 10 20 30 40 50 - 00 00 00 21 00 00 00 00 .`...0@P...!....
    00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
    00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................

    10:39:08 AM #23 Text 0 File Cdrdrv.cpp, Line 1195
    10:39:08.234 - D: Memorex DVD16+/-DL4RWlD2 : Queue again later

    10:42:41 AM #24 SPTI -1114 File SCSIPassThrough.cpp, Line 306
    CdRom3: SCSIStatus(x02) WinError(0) NeroError(-1114)
    Sense Key: 0x06 (KEY_UNIT_ATTENTION)
    Sense Code: 0x29
    Sense Qual: 0x00
    CDB Data: 0x2A 00 00 06 AB 00 00 00 20 00 00 00
    Sense Area: 0x70 00 06 00 00 00 00 0A 00 00 00 00 29
    Buffer x04010000: Len x10000
    0xEA A6 8F 94 22 7A 2E 83 BC 1C 91 9A 32 8D 8D E8
    0xE9 FB D5 7A 59 E6 43 77 9A A0 EE 91 B0 9E C6 C3
    0x54 B6 C7 6C D0 A0 33 55 32 74 64 12 30 9A AC D1

    10:42:41 AM #25 CDR -1114 File Writer.cpp, Line 302
    Reset occurred
    D: Memorex DVD16+/-DL4RWlD2

    10:42:41 AM #26 Text 0 File ThreadedTransfer.cpp, Line 228
    all writers idle, stopping conversion

    10:42:41 AM #27 Text 0 File ThreadedTransfer.cpp, Line 222
    conversion idle, stopping reader

    10:42:41 AM #28 Text 0 File DVDR.cpp, Line 2866
    EndDAO: Last written address was 436991

    10:42:41 AM #29 Phase 38 File dlgbrnst.cpp, Line 1724
    Burn process failed at 6x (8,310 KB/s)


    Existing drivers:
    File 'Drivers\ADPU160M.SYS': Ver=v3.60a (Lab01_N(johnstra).010529-2218), size=101888 bytes, created 8/17/2001 3:07:32 PM
    File 'Drivers\ASPI32.SYS': Ver=4.71 (0002), size=16877 bytes, created 7/17/2002 8:53:02 AM
    File 'Drivers\PXHELP20.SYS': Ver=3.00.11B, size=46080 bytes, created 5/16/2006 3:23:54 PM (Prassi/Veritas driver for win 2K)
    File 'Drivers\SCSIPORT.SYS': Ver=5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), size=96256 bytes, created 8/4/2004 6:00:00 AM (Adapter driver for src)

    Registry Keys:
    HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)

     
  8. binkie7

    binkie7 Moderator Staff Member

    Joined:
    Feb 12, 2005
    Messages:
    18,496
    Likes Received:
    0
    Trophy Points:
    116
    Yeah it could definitely be a media issue - the memorex you have are made by CMC - not very good.
    Plus the firmware for this drive hasn't been updated since mid 2005 so some 16x media will more than likely give it problems (like these).

    The drive is actually a oem LiteOn SOHW-1673S so you could also try crossflashing the drive to the LiteOn firmware. You would need to use the patched on for the LiteOn SOHW 1693S - KSOB. Here's a link if interested - link

    The 2mb buffer on the drive is pretty standard - you're good there.
     
  9. reefis

    reefis Member

    Joined:
    Feb 22, 2007
    Messages:
    11
    Likes Received:
    0
    Trophy Points:
    11
    DUDE!! you kick ass. you solved my problems 100%! It used to take an hour to burn a dvd and now it's 7 minutes. I was able to burn the CMC dvd-r at 16x. no problems at all. nero infotool even says i can read AND write bd-r. that can't be true, can it? wow. thank you so much!
     
  10. binkie7

    binkie7 Moderator Staff Member

    Joined:
    Feb 12, 2005
    Messages:
    18,496
    Likes Received:
    0
    Trophy Points:
    116
    lol - not a problem reefis :)

    I take it you cross flashed to the LiteOn and that did the trick.
    Though it won't have given the drive the ability to read & write to BluRay (check box will be to the right of BD-R). The LiteOn doesn't support it.

    I'd take the CMC back down to 8x too - don't need any more coasters :)
    And these can be iffy enuf as it is.

    Happy Burning!
     
  11. reefis

    reefis Member

    Joined:
    Feb 22, 2007
    Messages:
    11
    Likes Received:
    0
    Trophy Points:
    11
    yeah i was definately not looking at the check boxes correctly! you are very wise and i bow down to you!
     
  12. binkie7

    binkie7 Moderator Staff Member

    Joined:
    Feb 12, 2005
    Messages:
    18,496
    Likes Received:
    0
    Trophy Points:
    116
    LOL
    That check box has fooled many of us :)
     
  13. mark8766

    mark8766 Member

    Joined:
    Apr 29, 2006
    Messages:
    35
    Likes Received:
    0
    Trophy Points:
    16
    What a beautiful ending :)
     
  14. mark8766

    mark8766 Member

    Joined:
    Apr 29, 2006
    Messages:
    35
    Likes Received:
    0
    Trophy Points:
    16
    What a beautiful ending :)
     
  15. mark8766

    mark8766 Member

    Joined:
    Apr 29, 2006
    Messages:
    35
    Likes Received:
    0
    Trophy Points:
    16
    sorry didnt mean to double
     
  16. binkie7

    binkie7 Moderator Staff Member

    Joined:
    Feb 12, 2005
    Messages:
    18,496
    Likes Received:
    0
    Trophy Points:
    116
    lol - it happens to the best of us :) (double post)
     

Share This Page