1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Dvd Shrink Error "illegal Disc"

Discussion in 'DVD Shrink forum' started by talkhard, Jan 17, 2007.

  1. talkhard

    talkhard Member

    Joined:
    Jan 17, 2007
    Messages:
    85
    Likes Received:
    0
    Trophy Points:
    16
    I recently recieved an error "illegal disc" when I tried to copy video files to a dvd -r disc. The error happens when it try's to start burning.
    Before this, i bought a different, less expensive type of dvd disc's. But I don't think that it is the problem because I have since bought a better quality type of disc, Maxell -r and it still didn't work.
    I tried using Nero and it worked fine using the same video files. Then I tried an RW disc and IT worked fine. I have noticed other users geting this error and they posted an error log but I don't have a copy of mine. I could get it if I needed to.
    I haven't changed any settings on Shrink so I am at a bit of a loss here. If some could help me that would be fantastic!!
     
  2. johnl123

    johnl123 Regular member

    Joined:
    Nov 3, 2005
    Messages:
    2,421
    Likes Received:
    0
    Trophy Points:
    46
    Last edited: Jan 17, 2007
  3. talkhard

    talkhard Member

    Joined:
    Jan 17, 2007
    Messages:
    85
    Likes Received:
    0
    Trophy Points:
    16
    Thanks so much for your reply/help. I will try firmware update. If this doesn't help, I will post again and post the Nero log.
    Thanks again
     
  4. vballstud

    vballstud Guest

    Does your burner support DVD-R?

    Oops. I see John beat me to the punch...
     
    Last edited by a moderator: Jan 17, 2007
  5. talkhard

    talkhard Member

    Joined:
    Jan 17, 2007
    Messages:
    85
    Likes Received:
    0
    Trophy Points:
    16
    Ooops on me. I should have told you that yes my dvd burner supports dvd + and - R as well as RW.
     
  6. talkhard

    talkhard Member

    Joined:
    Jan 17, 2007
    Messages:
    85
    Likes Received:
    0
    Trophy Points:
    16
    Knowing almost nothing about this field of computers, explain to me how a dvd burner in need of an update in its firmware stop dvd shrink from working? how does that work?
     
  7. saugmon

    saugmon Senior member

    Joined:
    Oct 9, 2004
    Messages:
    6,064
    Likes Received:
    1
    Trophy Points:
    116
    Firmware: Is the programming for drives. This programming consists of how drives are to burn specific media. All blank media has MID codes. The firmware reads these codes,and then it knows how to properly burn them. It's the writing strategy. The firmware instructs the drive on how fast to burn it,increments of burning,and to properly burn them.

    When switching media,that MID code will likely change,even among batches of same exact brand name and quantity..

    Firmware updates:

    With the newer/faster media that comes out,manufacturers of burners will have their drives tested on the various MID codes. They gather all this info,develop a firmware version to handle them,then issue an update..There's instances where media quality is so crappy,they won't allow that burner to burn that specific media.They can also allow you to overburn media,and there's hacked firmware to make drives region free or booktyping capability.

    Firmware updates are up to the manufacturers.Some will have frequent updates,while other manufacturers won't. By having fewer updates,this is a way some brand named drives of telling you it's time to update to a newer burner.

    If you insert a specific media and get a no disc,or ejects during the lead-in phase,definite firmware update is needed. It also can affect stand alone playability.

    Dvd shrink does not burn. It only rips and compresses. It can use other programs to do the burning: Nero,ImgBurn,Dvd decrypter,and Copytodvd. If you have shrink set up to autoburn with any of those programs,you don't even realize you're using a burn program.
     
  8. talkhard

    talkhard Member

    Joined:
    Jan 17, 2007
    Messages:
    85
    Likes Received:
    0
    Trophy Points:
    16
    I really appreciate your thorough explaination of how it works. Truly, I knew about a third of what you just said, the rest ..just learned.
    So, 6 coasters later, no success. i have since tried something called flashing my dvd drive. i used the appropriate material, I believe so anyways. Someone suggested something called Epprom Utility 3.5.0. Is this really needed?
    I am sorry but I didn't get a copy of the error log but I do know that I have a LiteOn dvdrw shw-1635s firmware version ygs3. I couldn't find a firmware update on the LiteOn website. i found 3 similar but after a downloaded them, they told me that they didn't match my drive.
    I currently use dvdfab express. It has always worked well for me. I downloaded it about 4 months ago. The video files needed decrypting. Well, I should say that when I first started Shrink, some error would pop up so then I'd know to try running it through a decrypter, right? The decrypted file then runs through Shrink fine, BUT won't burn.
    Like I said, I have tried one Maxell dvd-r disc and about seven C2 Tech dvd-r disc's (thats the name) I know, cheaper. BUT NEITHER worked !!! The burn speed was always 4x or slower. I still recieved the illegal disc error.
    ANY SUGGESTIONS!! Is it firmware issue? Please help
     
    Last edited: Jan 18, 2007
  9. johnl123

    johnl123 Regular member

    Joined:
    Nov 3, 2005
    Messages:
    2,421
    Likes Received:
    0
    Trophy Points:
    46
    This is old, you need version YS0Z.

    Get the firmware update (YS0Z) here for LiteOn dvdrw shw-1635s:
    http://codeguys.rpc1.org/firmwares.html#SOHW-1693S

    Try the stock or the patched version for better performance. The file/s are in a .rar format so you'll need a utility to get at the contents, I recommend 7zip (free) if you don't have one already.

    7zip.exe http://www.7-zip.org/

    No.



    DVDFab decrypter/DVDshrink/and Nero is all you should need to get the backup.

    DVDFab latest beta
    http://www.dvdfab.com/DVDFabDecrypter3060Beta.exe

    Rip using DVDFab, open the files using shrink and auto burn to disk using nero.
     
    Last edited: Jan 18, 2007
  10. talkhard

    talkhard Member

    Joined:
    Jan 17, 2007
    Messages:
    85
    Likes Received:
    0
    Trophy Points:
    16
    OK. I updated the Firmware of my dvd burner to YSOZ and it still gives me the illegal disc error. It happens always at the point of burning. I even tried make a copy of something I already had on disc and it didn't burn. I am thinking that its the type of disc I am using. But here is a copy of the error log, just in case.

    1A20-
    Windows XP 5.1
    IA32
    WinAspi: -
    ahead WinASPI: File 'C:\Program Files\Ahead\Nero\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 26/10/2004 11:35:32 AM
    Nero API version: 6.6.0.15
    Using interface version: 6.3.1.4
    Installed in: C:\Program Files\Ahead\Nero\
    Application: ahead\Nero - Burning Rom
    Internal Version: 6, 6, 0, 15e

    Recorder: <LITE-ON DVDRW SHW-1635S> Version: YS0Z - HA 3 TA 0 - 6.6.0.15
    Adapter driver: <atapi> HA 3
    Drive buffer : 2048kB
    Bus Type : via Inquiry data (1) -> ATAPI, detected: ATAPI
    Connected to MMC as unknown drive with class-nr : 1
    Drive is autodetected - recorder class: Std. MMC recorder

    === Scsi-Device-Map ===
    DiskPeripheral : ST3200826A atapi Port 0 ID 0 DMA: On
    CdRomPeripheral : LITE-ON DVDRW SHW-1635S atapi Port 3 ID 0 DMA: On

    === CDRom-Device-Map ===
    LITE-ON DVDRW SHW-1635S E: CDRom0
    =======================

    AutoRun : 1
    Excluded drive IDs:
    WriteBufferSize: 83886080 (0) Byte
    ShowDrvBufStat : 0
    BUFE : 0
    Physical memory : 895MB (916848kB)
    Free physical memory: 388MB (397392kB)
    Memory in use : 56 %
    Uncached PFiles: 0x0
    Use Inquiry : 1
    Global Bus Type: default (0)
    Check supported media : Disabled (0)

    19.1.2007
    NeroAPI
    12:06:53 PM #1 Phase 112 File APIProgress.cpp, Line 276
    DVD-Video files reallocation started

    12:06:53 PM #2 Phase 114 File APIProgress.cpp, Line 276
    DVD-Video files reallocation completed (no file modified)

    12:06:53 PM #3 Phase 111 File APIProgress.cpp, Line 276
    DVD-Video files sorted

    12:06:53 PM #4 Text 0 File Reader.cpp, Line 127
    Reader running

    12:06:53 PM #5 Text 0 File Writer.cpp, Line 122
    Writer LITE-ON DVDRW SHW-1635S running

    12:06:53 PM #6 Text 0 File AudioCompilationImpl.cpp, Line 842
    DRM: StartDrmRecording(RealRec:1, ImageRec:0, Copies:1)
    DRM: Beginning burn process.

    12:06:54 PM #7 ISO9660GEN -11 File geniso.cpp, Line 3309
    First writeable address = 0 (0x00000000)

    12:06:54 PM #8 ISO9660GEN -11 File geniso.cpp, Line 3309
    First writeable address = 0 (0x00000000)

    12:06:54 PM #9 Text 0 File Burncd.cpp, Line 3231
    Turn on Disc-At-Once, using DVD media

    12:20:02 PM #10 Text 0 File DlgWaitCD.cpp, Line 267
    Last possible write address on media: 2298495 (510:46.45, 4489MB)
    Last address to be written: 2213423 (491:52.23, 4323MB)

    12:20:02 PM #11 Text 0 File DlgWaitCD.cpp, Line 279
    Write in overburning mode: NO

    12:20:02 PM #12 Text 0 File DlgWaitCD.cpp, Line 2457
    Recorder: LITE-ON DVDRW SHW-1635S, Media type: DVD-R
    Disc Manufacturer: TYG02 -
    Disc Application Code: 64, Disc Physical Code: 193

    12:20:02 PM #13 Text 0 File DlgWaitCD.cpp, Line 445
    >>> Protocol of DlgWaitCD activities: <<<
    =========================================
    Insert empty disc to write to.
    (Medium in drive: unknown. Medium required by compilation: DVD+R/RW, DVD-R/RW, DVD-R DL, DVD+R DL.)

    12:20:02 PM #14 Text 0 File ThreadedTransferInterface.cpp, Line 830
    Setup items (after recorder preparation)
    0: TRM_DATA_MODE1 ()
    2 indices, index0 (150) not provided
    original disc pos #0 + 2213424 (2213424) = #2213424/491:52.24
    relocatable, disc pos for caching/writing not required/ required, no patch infos
    -> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2213424 blocks [LITE-ON DVDRW SHW-1635S]
    --------------------------------------------------------------

    12:20:02 PM #15 Text 0 File ThreadedTransferInterface.cpp, Line 1043
    Prepare recorder [LITE-ON DVDRW SHW-1635S] for write in CUE-sheet-DAO
    DAO infos:
    ==========
    MCN: ""
    TOCType: 0x00; Session Closed, disc fixated
    Tracks 1 to 1:
    1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4533092352, ISRC ""
    DAO layout:
    ===========
    __Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
    0 | lead-in | 0 | 0x41 | 0x00
    0 | 1 | 0 | 0x41 | 0x00
    0 | 1 | 1 | 0x41 | 0x00
    2213424 | lead-out | 1 | 0x41 | 0x00

    12:20:02 PM #16 Phase 24 File APIProgress.cpp, Line 276
    Caching of files started

    12:20:02 PM #17 Text 0 File Burncd.cpp, Line 4116
    Cache writing successful.

    12:20:02 PM #18 Phase 25 File APIProgress.cpp, Line 276
    Caching of files completed

    12:20:02 PM #19 Phase 36 File APIProgress.cpp, Line 276
    Burn process started at 4x (5,540 KB/s)

    12:20:02 PM #20 Text 0 File ThreadedTransferInterface.cpp, Line 2643
    Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

    12:20:02 PM #21 Text 0 File DVDR.cpp, Line 2340
    Recording mode: Sequential Recording Mode

    12:20:02 PM #22 Text 0 File Mmc.cpp, Line 21627
    Set BUFE: Buffer underrun protection -> ON , SMART-BURN : ON

    12:20:02 PM #23 Text 0 File DVDR.cpp, Line 2494
    Start write address at LBA 0
    DVD high compatibility mode: Yes

    12:20:02 PM #24 Text 0 File Cdrdrv.cpp, Line 8821
    ---- DVD Structure: Physical Format Information (00h) ----
    Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
    Book Type: DVD-R (2), Part Version: 5
    Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
    Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
    Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
    Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
    End Physical Sector Number of Data Area: 26127F h
    End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
    Data in Burst Cutting Area (BCA) does not exist
    Start sector number of the current Border-Out: 0 h
    Start sector number of the next Border-In: 0 h
    Media Specific [16..63]:
    00 20 01 02 00 04 00 06 - 00 08 00 00 00 00 00 00 ................
    00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
    00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................

    12:20:29 PM #25 Text 0 File Cdrdrv.cpp, Line 1288
    12:20:29.571 - LITE-ON DVDRW SHW-1635S\H3 T0 : Queue again later

    12:24:12 PM #26 SCSI -1046 File Cdrdrv.cpp, Line 1436
    SCSI Exec, HA 3, TA 0, LUN 0, buffer 0x00F80000
    Status: 0x04 (0x01, SCSI_ERR)
    HA-Status 0x00 (0x00, OK)
    TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
    Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
    Sense Code: 0x30
    Sense Qual: 0x05
    CDB Data: 0x2A 0x00 0x00 0x00 0x1A 0xC0 0x00 0x00 0x20 0x00 0x00 0x00
    Sense Data: 0x70 0x00 0x05 0x00 0x00 0x00 0x00 0x0A
    0x00 0x00 0x00 0x00 0x30 0x05

    12:24:12 PM #27 CDR -1046 File Writer.cpp, Line 311
    Illegal disc

    12:24:12 PM #28 Text 0 File ThreadedTransfer.cpp, Line 228
    all writers idle, stopping conversion

    12:24:12 PM #29 Text 0 File ThreadedTransfer.cpp, Line 222
    conversion idle, stopping reader

    12:24:12 PM #30 Text 0 File DVDR.cpp, Line 2732
    EndDAO: Last written address was 6847

    12:24:13 PM #31 Phase 38 File APIProgress.cpp, Line 276
    Burn process failed at 4x (5,540 KB/s)

    12:24:13 PM #32 Text 0 File AudioCompilationImpl.cpp, Line 867
    DRM: DRM burn session terminated.

    12:24:13 PM #33 Text 0 File AudioCompilationImpl.cpp, Line 896
    DRM: Closing entire DRM handling. Bye.


    Existing drivers:
    File 'Drivers\ADPU160M.SYS': Ver=v3.60a (Lab01_N(johnstra).010529-2218), size=101888 bytes, created 17/08/2001 11:07:32 PM
    File 'Drivers\CDRALW2K.SYS': Ver=8.0.0.212 , size=2560 bytes, created 05/01/2007 11:30:59 PM
    File 'Drivers\PXHELP20.SYS': Ver=3.00.33a, size=36528 bytes, created 05/01/2007 11:30:55 PM (Prassi/Veritas driver for win 2K)

    Registry Keys:
    HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
     
    Last edited: Jan 19, 2007
  11. johnl123

    johnl123 Regular member

    Joined:
    Nov 3, 2005
    Messages:
    2,421
    Likes Received:
    0
    Trophy Points:
    46
    Media Specific [16..63]:
    00 20 01 02 00 04 00 06 - 00 08 00 00 00 00 00 00 ................
    00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
    00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ..............

    This part suggests that the disks are not liked:
    Disc Manufacturer: TYG02 -


    Try verbatim.
     
  12. solarf

    solarf Member

    Joined:
    Dec 2, 2006
    Messages:
    11
    Likes Received:
    0
    Trophy Points:
    11
    DO most burners prefer a certain type of media?
     
  13. saugmon

    saugmon Senior member

    Joined:
    Oct 9, 2004
    Messages:
    6,064
    Likes Received:
    1
    Trophy Points:
    116
    Is that nero log from those C2 Tech blanks? I never heard of them.

    TyG02 are some very good discs,if they are genuine.[bold]That MID code has been faked[/bold] with generic brand name media. To find out if they are genuine,get a bright light at look at the bottom of the discs. Near the center hub,look at the purple for a code which should look like:

    GH000073 or similar. 2 letters in large caps and 6 numbers following.

    The MID code can be faked,but not that batch number. If they are from those C2 techs,beware of them. Post back that batch number-but it probably won't have one.

    Some do prefer certain media and even certain formats. Lite-on drives are booktyping drives.These booktyping drives turn the plus format into the dvd-rom format-giving them a higher compatability rate. It's far superior to the dash format. The dash format is superior to the non booktyped + format. Burners should play their own backups. But reading backups from other burners and other stand alone players-the dreaded no disc error pops up when they don't recognize backups.

    I use Benq drives,which highly favor the plus format,booktyping reasons.The dash does give them more issues-higher coaster percentage and a 75% stand alone compatability rate.

    Now a no disc error from a burner from a blank disc:Could be bad media-faked or bad batch from the manufacturer,or a firmware issue-in which the burner's manufacturer doesn't recommend using a certain media,so the firmware will not allow burning that specific media.Or the drive is bad,if you get that no disc error with all types of blank media.

    I see a lot of people having trouble with -8x maxell Ritek-G05 media,whereas the +8x maxell Ritek-R03 are very good. Those same exact Maxell 8x are made by 3 different manufacturers for each format. Ritek,Hitachi,and CMC Mag. Someone may have gotten great backups with maxell hitachis,meanwhile their next batch may be ritek,or even worse-cmags. This is normal with most brands of media: HP,Sony,Philips,TDK,memorex,fuji,etc. That's what gives brand name media a bad rap because quality will vary when switching spindles.
    That's why genuine Taiyo Yuden and Verbatim are top dogs among media. Both have high quality control standards,the dye is Advanced Metal AZO, and will eliminate a slew of issues- Playback,less coasters,and Longevity.If you can find the Maxell Hitachi's-which the shrink wrapper will say Made in Japan,those are also sweet.

    BTW talkhard. Go to your post with the burn log and click on the pencil/notepad icon in the orange-on the top right corner.Then edit out your serial # from nero. It can be stolen and it looks like:
    1A20-xxxx-xxxx-xxxx-xxxx-xxxx

    The rest of the log looked ok. DMA's enabled,not burning too much data,no remnants of an older version of nero.
     
  14. talkhard

    talkhard Member

    Joined:
    Jan 17, 2007
    Messages:
    85
    Likes Received:
    0
    Trophy Points:
    16
    I would really like to thank all of you guys John and saugmon for all your help. i will go and buy some new blank dvds. i am very thankful that you guys know how to read those error logs and know so much about dvds and burning. I, on the other hand, have a bit to learn. I feel a lesson learned.
    The error log IS from the C2 Tech dvds and I will be certain to post the info I get. Thanks for the heads up on the Nero serial number. Thanks again guys and I will check back soon.
    Eternally grateful
     
    Last edited: Jan 19, 2007
  15. johnl123

    johnl123 Regular member

    Joined:
    Nov 3, 2005
    Messages:
    2,421
    Likes Received:
    0
    Trophy Points:
    46
    @talkhard

    No problem, happy to help:)
     
  16. talkhard

    talkhard Member

    Joined:
    Jan 17, 2007
    Messages:
    85
    Likes Received:
    0
    Trophy Points:
    16
    Hey guys. Saugmon wanted me to post the batch number of those C2 Tech dvds. I have a number here in the purple part of the hub of the disc and it reads ..DVD-R 8x 267, thats it. There is also a second code on the clear part of the disc that reads..IFPI EJO3. Thats all I got. I have a website printed on the bottom, front of the disc's ccandu.com

    later
     
    Last edited: Jan 20, 2007
  17. ARose13

    ARose13 Member

    Joined:
    Jan 31, 2007
    Messages:
    2
    Likes Received:
    0
    Trophy Points:
    11
    I am having this exact same problem! I have done everything... I'm at a loss. It was burning Office Depot DVD-Rs just fine, I ran out. I went out the next day and bought some Maxell DVD-Rs. They won't burn. I'm getting the same message. Error- Illegal Disc. The drive burns CDs just fine, but I've tried everything. We're independent filmmakers, so I tried just burning off footage, still won't work. I have been burning for as long as one could burn anything and I've never seen this. Please, any help would be great!!!!
     
  18. talkhard

    talkhard Member

    Joined:
    Jan 17, 2007
    Messages:
    85
    Likes Received:
    0
    Trophy Points:
    16
    I know through my experience that Maxell's didn't work well with my dvd burner either. I have a few coasters as a result of bad media type. Maybe try another brand?
     
    Last edited: Jan 31, 2007
  19. saugmon

    saugmon Senior member

    Joined:
    Oct 9, 2004
    Messages:
    6,064
    Likes Received:
    1
    Trophy Points:
    116
    ARose13: Update the firmware for your burner.

    What's the brand name,model#,and current firmware version?

    What's the speed rate of those Office Depot and Maxells? Locate the MID codes.

    Maxell has had up to 4 different manufacturers for their media,therefore 4 different MID codes for the exact same speed rated media.

    Office depot uses a lot of Ritek media,and a little bit of ricohjpn. Not too shabby. Maxell uses Hitachi,Ritek,and cmags-huge quality difference between those 3.

    Try to pick up some verbatim. Easy to find,and when on sale-under $15 per 50 pk at Bestbuy,Office depot,Office Max,etc.
     
  20. vivek_dvd

    vivek_dvd Member

    Joined:
    Feb 2, 2007
    Messages:
    2
    Likes Received:
    0
    Trophy Points:
    11
    Hi. Can somebody help me with a similar problem [as talkhard's] i'm having with my DVD burning. I use a SONY notebook and SONY DVD-R media. illegal disc. while i've burnt quite a few DVD's with the same media & NERO combination i've lost about 8 DVD's to this error since last night. i also tried the 'Sony DW-Q520A DVD-RW Firmware HYS2 download
    Sony DW-Q520A DVD-RW Firmware HYS2.
    FileName:HYS2WIN.EXE' download but installation failed. can somebody please help. thank you.

    _______________ERROR LOG_______________________________________
    Windows XP 5.1
    IA32
    WinAspi: -
    ahead WinASPI: File 'C:\Program Files\Ahead\nero\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 10/26/2004 6:35:34 PM
    Nero Version: 6.6.0.13
    Internal Version: 6, 6, 0, 13c
    (Nero Express)
    Recorder: <SONY DVD RW DW-Q520A> Version: HFS2 - HA 1 TA 0 - 6.6.0.13
    Adapter driver: <atapi> HA 1
    Drive buffer : 2048kB
    Bus Type : via Inquiry data (1) -> ATAPI, detected: ATAPI
    Connected to MMC as unknown drive with class-nr : 1
    Drive is autodetected - recorder class: Std. MMC recorder
    CD-ROM: <SONY DVD RW DW-Q520A >Version: HFS2 - HA 1 TA 0 - 6.6.0.13
    Adapter driver: <atapi> HA 1

    === Scsi-Device-Map ===
    DiskPeripheral : FUJITSU MHV2080BH PL atapi Port 0 ID 0 DMA: On
    CdRomPeripheral : SONY DVD RW DW-Q520A atapi Port 1 ID 0 DMA: On

    === CDRom-Device-Map ===
    SONY DVD RW DW-Q520A F: CDRom0
    =======================

    AutoRun : 1
    Excluded drive IDs:
    WriteBufferSize: 73400320 (0) Byte
    ShowDrvBufStat : 0
    BUFE : 0
    Physical memory : 502MB (514160kB)
    Free physical memory: 28MB (28968kB)
    Memory in use : 94 %
    Uncached PFiles: 0x0
    Use Inquiry : 1
    Global Bus Type: default (0)
    Check supported media : Disabled (0)

    2.2.2007
    UDF/ISO compilation
    10:45:03 PM #1 Phase 112 File dlgbrnst.cpp, Line 1832
    DVD-Video files reallocation started

    10:45:03 PM #2 Phase 114 File dlgbrnst.cpp, Line 1832
    DVD-Video files reallocation completed (no file modified)

    10:45:03 PM #3 Text 0 File Isodoc.cpp, Line 6194
    Iso document burn settings
    ------------------------------------------
    Determine maximum speed : FALSE
    Simulate : FALSE
    Write : TRUE
    Finalize CD : TRUE
    Multisession : FALSE
    Burning mode : DAO
    Mode : 1
    ISO Level : 1 (Max. of 11 = 8 + 3 char)
    Character set : ISO 9660
    Joliet :FALSE
    Allow pathdepth more than 8 directories : FALSE
    Allow more than 255 characters in path : FALSE
    Write ISO9660 ;1 file extensions : TRUE

    10:45:03 PM #4 Phase 111 File dlgbrnst.cpp, Line 1832
    DVD-Video files sorted

    10:45:03 PM #5 Text 0 File Reader.cpp, Line 127
    Reader running

    10:45:03 PM #6 Text 0 File Writer.cpp, Line 122
    Writer SONY DVD RW DW-Q520A running

    10:45:03 PM #7 ISO9660GEN -11 File geniso.cpp, Line 3293
    First writeable address = 0 (0x00000000)

    10:45:03 PM #8 ISO9660GEN -11 File geniso.cpp, Line 3293
    First writeable address = 0 (0x00000000)

    10:45:04 PM #9 Text 0 File Burncd.cpp, Line 3167
    Turn on Disc-At-Once, using DVD media

    10:46:01 PM #10 Text 0 File DlgWaitCD.cpp, Line 260
    Last possible write address on media: 2298495 (510:46.45, 4489MB)
    Last address to be written: 2286127 (508:01.52, 4465MB)

    10:46:01 PM #11 Text 0 File DlgWaitCD.cpp, Line 272
    Write in overburning mode: NO (enabled: CD)

    10:46:01 PM #12 Text 0 File DlgWaitCD.cpp, Line 2339
    Recorder: SONY DVD RW DW-Q520A, Media type: DVD-R
    Disc Manufacturer: SONY16 - D1
    Disc Application Code: 64, Disc Physical Code: 193

    10:46:01 PM #13 Text 0 File DlgWaitCD.cpp, Line 438
    >>> Protocol of DlgWaitCD activities: <<<
    =========================================
    Insert empty disc to write to.
    (Medium in drive: Unknown. Medium required by compilation: DVD+R/RW, DVD-R/RW, DVD-R DL, DVD+R DL.)

    10:46:01 PM #14 Text 0 File ThreadedTransferInterface.cpp, Line 830
    Setup items (after recorder preparation)
    0: TRM_DATA_MODE1 ()
    2 indices, index0 (150) not provided
    original disc pos #0 + 2286128 (2286128) = #2286128/508:1.53
    relocatable, disc pos for caching/writing not required/ required, no patch infos
    -> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2286128 blocks [SONY DVD RW DW-Q520A]
    --------------------------------------------------------------

    10:46:01 PM #15 Text 0 File ThreadedTransferInterface.cpp, Line 1043
    Prepare recorder [SONY DVD RW DW-Q520A] for write in CUE-sheet-DAO
    DAO infos:
    ==========
    MCN: ""
    TOCType: 0x00; Session Closed, disc fixated
    Tracks 1 to 1:
    1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4681990144, ISRC ""
    DAO layout:
    ===========
    __Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
    0 | lead-in | 0 | 0x41 | 0x00
    0 | 1 | 0 | 0x41 | 0x00
    0 | 1 | 1 | 0x41 | 0x00
    2286128 | lead-out | 1 | 0x41 | 0x00

    10:46:02 PM #16 Phase 24 File dlgbrnst.cpp, Line 1832
    Caching of files started

    10:46:02 PM #17 Text 0 File Burncd.cpp, Line 4051
    Cache writing successful.

    10:46:02 PM #18 Phase 25 File dlgbrnst.cpp, Line 1832
    Caching of files completed

    10:46:02 PM #19 Phase 36 File dlgbrnst.cpp, Line 1832
    Burn process started at 8x (11,080 KB/s)

    10:46:02 PM #20 Text 0 File ThreadedTransferInterface.cpp, Line 2609
    Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

    10:46:03 PM #21 Text 0 File DVDR.cpp, Line 2267
    Recording mode: Sequential Recording Mode

    10:46:03 PM #22 Text 0 File Mmc.cpp, Line 21469
    Set BUFE: Power-Burn -> ON , Adapt writespeed to disc : ON

    10:46:03 PM #23 Text 0 File DVDR.cpp, Line 2421
    Start write address at LBA 0
    DVD high compatibility mode: Yes

    10:46:03 PM #24 Text 0 File Cdrdrv.cpp, Line 8438
    ---- DVD Structure: Physical Format Information (00h) ----
    Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
    Book Type: DVD-R (2), Part Version: 5
    Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
    Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
    Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
    Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
    End Physical Sector Number of Data Area: 26127F h
    End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
    Data in Burst Cutting Area (BCA) does not exist
    Start sector number of the current Border-Out: 0 h
    Start sector number of the next Border-In: 0 h
    Media Specific [16..63]:
    00 60 00 10 20 30 40 50 - 00 00 00 21 00 00 00 00 .`...0@P...!....
    00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
    00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................

    10:46:45 PM #25 Text 0 File Cdrdrv.cpp, Line 1288
    22:46:45.046 - SONY DVD RW DW-Q520A\H1 T0 : Queue again later

    10:51:27 PM #26 SCSI -1046 File Cdrdrv.cpp, Line 1436
    SCSI Exec, HA 1, TA 0, LUN 0, buffer 0x0B180000
    Status: 0x04 (0x01, SCSI_ERR)
    HA-Status 0x00 (0x00, OK)
    TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
    Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
    Sense Code: 0x30
    Sense Qual: 0x05
    CDB Data: 0x2A 0x00 0x00 0x00 0x04 0xA0 0x00 0x00 0x20 0x00 0x00 0x00
    Sense Data: 0x70 0x00 0x05 0x00 0x00 0x00 0x00 0x0A
    0x00 0x00 0x00 0x00 0x30 0x05

    10:51:27 PM #27 CDR -1046 File Writer.cpp, Line 311
    Illegal disc

    10:51:27 PM #28 Text 0 File ThreadedTransfer.cpp, Line 228
    all writers idle, stopping conversion

    10:51:28 PM #29 Text 0 File ThreadedTransfer.cpp, Line 222
    conversion idle, stopping reader

    10:51:28 PM #30 Text 0 File DVDR.cpp, Line 2658
    EndDAO: Last written address was 1183

    10:51:28 PM #31 Phase 38 File dlgbrnst.cpp, Line 1832
    Burn process failed at 8x (11,080 KB/s)


    Existing drivers:
    File 'Drivers\CDRALW2K.SYS': Ver=8.0.0.212 , size=2560 bytes, created 10/28/2005 3:30:00 PM
    File 'Drivers\PXHELP20.SYS': Ver=3.00.10a, size=46080 bytes, created 10/28/2005 3:30:00 PM (Prassi/Veritas driver for win 2K)
    File 'Drivers\atapi.sys': Ver=5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), size=95360 bytes, created 8/4/2004 12:29:44 PM (Adapter driver for rec)

    Registry Keys:
    HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
    ____________________________________________________________________
     

Share This Page