1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Having difficulty burning

Discussion in 'DVD Shrink forum' started by icgy420, Apr 22, 2007.

  1. icgy420

    icgy420 Member

    Joined:
    Apr 22, 2007
    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    11
    Thanks for the help all!
     
    Last edited: Apr 24, 2007
  2. colw

    colw Active member

    Joined:
    Apr 25, 2004
    Messages:
    1,735
    Likes Received:
    0
    Trophy Points:
    66

    __________________________________________________________________
    === Scsi-Device-Map ===
    CdRomPeripheral : DVD RW DVR-MCC atapi Port 0 ID 0 DMA: Off
    CdRomPeripheral : DVD ROM DX-DVDR100 atapi Port 0 ID 1 DMA: Off
    DiskPeripheral : ST3200822AS atapi Port 1 ID 0 DMA: On
    __________________________________________________________________

    Appears that your burner and DVD ROM have reverted to PIO mode. You will need to re-enable DMA on both.
     
  3. PacMan777

    PacMan777 Regular member

    Joined:
    Jun 11, 2013
    Messages:
    3,836
    Likes Received:
    0
    Trophy Points:
    46
    Check in Device Manager to see if DMA or PIO is on. For IDE setups the Secondary channel usually has the optical drives and the hard drives are on the Primary. Double click the channel and look in Advanced Settings or right click the desired channel and select Properies and look under the Advanced Settings tab. Note current transfer mode. Transfer Mode: is the setting that's desired, not necessarily what the drive is in, that's the Current Transfer Mode. DMA doesn't apply to SATA.

    [​IMG]

    #I is the Control Panel. Follow I, II, III. Hard drives on Primary Channel and optical drives on Secondary Channel. Uninstall and reboot to kick drives back into DMA on. After Reboot check to make sure DMA is on. If problems persist, check IDE cables, drives and mobo.
    [​IMG]
     
  4. icgy420

    icgy420 Member

    Joined:
    Apr 22, 2007
    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    11
    :)
     
    Last edited: Apr 24, 2007
  5. 300bowler

    300bowler Regular member

    Joined:
    May 16, 2006
    Messages:
    1,918
    Likes Received:
    0
    Trophy Points:
    46
    Hello,

    File 'Drivers\CDRALW2K.SYS': Ver=8.0.0.212 , size=2560 bytes, created 5/19/2006 2:16:24 PM

    This is a roxio driver, which is known to conflict with nero
    use this tool to get rid
    http://www.softpedia.com/get/Tweak/Uninstallers/Roxio-Zap.shtml

    i am not sure what Internal target failure
    means, what for other AD members thoughts on that
     
  6. PacMan777

    PacMan777 Regular member

    Joined:
    Jun 11, 2013
    Messages:
    3,836
    Likes Received:
    0
    Trophy Points:
    46
    I suspect the target error is the drive. Along with the driver you pointed out is this error:
    Status: 0x04 (0x01, SCSI_ERR)
    HA-Status 0x00 (0x00, OK)
    TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
    Sense Key: 0x04 (KEY_HARDWARE_ERROR)

    This is a drive error. The best thing to do is to clear the Roxio driver and see if that frees the drive to work properly.
     
  7. icgy420

    icgy420 Member

    Joined:
    Apr 22, 2007
    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    11
    :)
     
    Last edited: Apr 24, 2007
  8. PacMan777

    PacMan777 Regular member

    Joined:
    Jun 11, 2013
    Messages:
    3,836
    Likes Received:
    0
    Trophy Points:
    46
    Before I say check the hardware and possibly replace the drive, I'll suggest using some different media. Sony +R (not -R), Verbatim, Taiyo Yuden, Ricoh, or one of the name brands with made in Japan on the label are usually some of the good stuff. If the good media doesn't work, try using ImgBurn or another burner program. That helps determine if it's software or hardware. Then, if none of the previous options help, you need to check the cable, connections, and the drive.
     
    Last edited: Apr 24, 2007

Share This Page