Help needed !!!!

MrSpots · Feb 8, 2007

can some one re wite this so i can understand it better.

Attention! Editorial staff did not verify information method, so that each using it, makes this at one's own risk! The discussion will deal with the error "An error occurred while copying Setup files onto your local machine. Error code is [ 80070241 ] ", that indicates" during the copying it is file to your machine it occurred the error... " We will attempt to solve this problem, without the repeated running off or the purchase of distributiva. By you two programs will be necessary for this. This Win32Dasm 10 and WinHex 11.8. It can be, other versions also approach, but the author removed trouble precisely by them. It is first necessary to copy all files from the adjusting disk to the hard disk. As an example, the files were copied into the folder of /.Vista. You should open file winsetup.dll (/Vista/sources/winsetup.dll) by application Win32Dasm (process of discovery it can engage prolonged time). After discovery, pass to the search (Search Find Text or simply press F3). In afterward search introduce "while copying Setup files" and switch over to the obtained line (this line only one in the code). Now you should begin to move in the lines upward, until you find the following text: "JNE 448797B4". Possibly, numbers will be different, but command "JNE" (or JE) compulsorily must be in other words, you must prove to be on the proximity of the following text: Code: Cmp DWORD Ptr... jne... push.. push.. call.. push.. Now produce dual flick in line jne in order to isolate it. After isolation, on the line of state; there you must find the following: "@Offset 00068D07h" (number they can be others). Write down this line, after discarding @Offset in the beginning the last letter h. Further pass in WinHex and open the same winsetup.dll. The collection of the numbers and symbols will appear before you. Press Alt+.G (or pass in menu Position Goto offset). There you must introduce the number (in my case this 0068D07) recorded by you. After pressure ok, you will see the following line: Code: 00068D00 01 00 00 00 39 75 F8 0F 85 A7 00 00 00 56 56 ff If in this line you have number 85, then you will replace it to 84. If you have by 84, you must change it for 85. Then you will preserve changes in the file. After the completion of these actions, you will neglect installation (/Vista/Sources/setup.exe) and wait, until the first stage appears. Further, anything touching in the installation, pass in conductor (pushing of knob start on the keyboard and the selection of conductor), and then into the root of disk C: =, where two folders were created. In one of them there is podpapka sources, where you should copy files boot.wim, and install.wim. After copying you can continue installation.
Click to expand...

this is so you can install windows vista succsesfully without the error code that pops-up at the 49% mark.

PeaInAPod · Feb 14, 2007

basically:

Attention! Editorial staff did not check this method/procedure so doing this will be doing so at your own risk.This little paper will deal with "An error occurred while copying Setup files onto your local machine. Error code is [ 80070241 ]. This means a file couldn't be copied to your computer during install. We will attempt to solve this problem with two programs. You will need Win32Dasm 10 and WinHex 11.8. You can use other versions. It is first necessary to copy all files from the install disk to the hard-drive. As an example, the files were copied into a folder called "Vista". You should open file winsetup.dll (/Vista/sources/winsetup.dll) by using Win32Dasm (it can take a long time for it to open, this is normal). After Win32Dasm is open, press F3. The search for "while copying Setup files" and click on whatever the program returned as a result(this should be only 1 line in the code). Now you should begin to move in the upward in the code/lines, until you find the following text: "JNE 448797B4". Numbers may be different, but the word "JNE" (or JE)must be there. And it must be close to the following text: Code: Cmp DWORD Ptr... jne... push.. push.. call.. push.. (this line lost me)Now produce dual flick in line jne in order to isolate it. After finding it you must find the following: "@Offset 00068D07h" (the numbers can be different). Write down this line but don't include @Offset or the last letter, which is an "h". Nowopen the same winsetup.dll in WinHex. A collection of the numbers and symbols will appear before you. Press Alt+.G here you must type in the number you wrote down (0068D07). Hit "Enter"/"Ok", you will see the following line:

Code: 00068D00 01 00 00 00 39 75 F8 0F 85 A7 00 00 00 56 56 ff

If in this line you have number 85, then you will replace it to 84. If you have by 84, you must change it for 85. Then you will save the changes you made to the file. After the completion of these actions, you will skip installation (/Vista/Sources/setup.exe) and wait until the first stage of setup appears. Then press "Start"/"Windows Icon" on the keyboard and "log in" into the root of disk C: =, where two folders should be. In one of them there is something called/referring to podpapka sources, where you should copy files the files boot.wim and install.wim. After copying these files you can continue installation.
Click to expand...

good luck - Pea.

Log in or Sign up

Help needed !!!!

MrSpots Guest

PeaInAPod Active member

Share This Page

Log in or Sign up

Help needed !!!!

MrSpots Guest

PeaInAPod Active member

Share This Page

Useful Searches