1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Session fixation error???

Discussion in 'DVD±R for advanced users' started by Nascar40, Mar 3, 2005.

  1. Nascar40

    Nascar40 Member

    Joined:
    Jan 4, 2005
    Messages:
    52
    Likes Received:
    0
    Trophy Points:
    16
    Ok, Just in the last few weeks my burnner has started acting up, it keeps giving me a error when the disc start's to burn and I don't know why. This is the error as seen in nero recode2.

    21:04:41 DVD-Video Files sorted
    21:04:41 Caching of files started
    21:04:41 Caching of files completed
    21:04:41 Burn process started at 8x(11,080kb/s)
    21:05:03 Write error
    21:05:04 Session fixation error
    21:05:04 Could not perform end of Disc-at-once
    21:05:04 Burn process failed at x8 (11,080kb/s)

    I don't know what that mean's but not just nero that messes up recrodnow! dose it to.

    Also where you can see it saying "Could not perform end of Disc-at-once" I don't know why it says that couse I had Disc-at-once trunned off.
    Can someone please help me. Thanks
     
  2. kchev

    kchev Regular member

    Joined:
    Nov 3, 2004
    Messages:
    455
    Likes Received:
    0
    Trophy Points:
    26
    i would try updating firmware and get some different media, but it is probably bad media
     
  3. Nascar40

    Nascar40 Member

    Joined:
    Jan 4, 2005
    Messages:
    52
    Likes Received:
    0
    Trophy Points:
    16
    I already got the newest firmware, and it dose it on TDK, Sony, and Verbatin. But also I use 2 computer to burn, and it only has that error on one computer
     
  4. kchev

    kchev Regular member

    Joined:
    Nov 3, 2004
    Messages:
    455
    Likes Received:
    0
    Trophy Points:
    26
    sounds like the drive is dying if it does it one every brand of disc
     
  5. Nascar40

    Nascar40 Member

    Joined:
    Jan 4, 2005
    Messages:
    52
    Likes Received:
    0
    Trophy Points:
    16
    It dose it on all brand's but not all disc about half of what I burn it dose it on.
     
    Last edited: Mar 4, 2005
  6. Rotary

    Rotary Senior member

    Joined:
    Apr 10, 2003
    Messages:
    8,353
    Likes Received:
    0
    Trophy Points:
    116
    4. DMA Settings
    Setting DMA mode:

    Windows 95/98/ME Users

    Right click on [My Computer] and select [Properties] from the menu. Click on [Device Manager], then click on [CD-ROM]. This will expand to show the CD drives on your system. Right click on a drive and select [Properties] from the menu. Click on the [Settings] tab and check that the [DMA] option is enabled. Repeat this procedure for the remaining CD drives.

    Win NT/2000/XP Users

    Right click on [My Computer] and select [Properties] from the menu. Click [Device Manager] on the [Hardware] tab, then click to open the [IDE ATA/ATAPI (hard disk) controllers] section. You will find: the Primary IDE Channel controller, Secondary IDE Channel controller. Complete the following procedure:

    Right click on the Primary IDE controller and select [Properties] from the menu.
    Select the [Advanced Settings] tab. Check that the [Transfer Mode] for both devices is set to [DMA if available].
    Repeat this for Secondary IDE controller.


    Note: In some cases older CD-ROM drives will not support DMA mode. In that case please set both devices to PIO mode.
    =============================

    5. Disc



    Recording errors often occur when the disc is dirty, or has fingerprints or scratches. If an error occurred during test simulation (before actual recording), clean the disc. If you are getting recording errors, try the following.
    Use a different blank, recordable disc.
    Use a different manufacturer's disc.
    Ensure the disc is clean before recording:
    Remove all fingerprints, dirt, and dust from the shiny side of your disc using a nonabrasive cloth with a mild, nonabrasive soap solution.
    Wipe the disc from the center to the edge of the disc.
    Dry the disc completely.


    Error during file verification
    If an error occurred when the files were being verified, record the same files again using a different disc.


    Read error when copying a disc
    When copying a disc, if an error occurred while reading data from the original disc, the original disc may be scratched or dirty.
    Try cleaning the disc.
    Remove all fingerprints, dirt, and dust from the shiny side of your disc using a nonabrasive cloth with a mild, nonabrasive soap solution.
    Wipe the disc from the center to the edge of the disc.
    Dry the disc completely.
    Try using a different source drive.
    To change the drive you use to read your disc, click the Change button when asked to insert a source disc into your drive tray.
    Select the drive you wish to use from the drop-down menu.
    Insert your disc into the new drive.
    Try using copying the disc using one drive as both the source and destination drive.
    When you use your recorder to both read and write to your disc, B's Recorder GOLD creates an image file of the entire disc to your hard drive and then copies that temporary file onto your blank disc. This can be helpful if the drive you are using to read your original disc is slow or unreliable.

    If the problem persists, contact the drive maker.

    =============================

    6. Drive
    If you have tried Actions 1 through 5 above, there may be a problem with your drive. Contact the drive maker with details of the error code. If the 5th and 6th digit of the error code is 80 through FF, then the error code is maker unique. The descriptions of these error codes differ depending on the maker.

     
  7. Nascar40

    Nascar40 Member

    Joined:
    Jan 4, 2005
    Messages:
    52
    Likes Received:
    0
    Trophy Points:
    16
    It's all set in DMA Mode, I hope this 3 mouth old burnner ain't bad HP 630i.

    Thank you all for tring to help me

    P.S. One more thing what dose (Session fixation error) mean most of the time just Bad midia?
     
    Last edited: Mar 4, 2005
  8. itsu42

    itsu42 Member

    Joined:
    Aug 25, 2004
    Messages:
    1
    Likes Received:
    0
    Trophy Points:
    11
    Hi.

    I've had the exact same problem for the last week. Suddenly, ever single attempt to burn a DVD+R at 4X, from the same spindle of Memorex 4X which I've been using for months with no bother, I get the error you do from Nero.

    Same thing with CDBurnerXP Pro, which tells me it "couldn't close lead-in - error 1043, sense 3, ASC 72, ASCQ 1".

    I just can't fathom why the thing should suddenly stop working? DVD+RW and DVD-RW still burn fine.

    Could this be another "side effect" of a windows security patch? I'm on an XP Pro SP1 (no SP2 yet) patched up to date.

    Drive is a BENQ 1620, flashed up to B7H9.

    Cheers
     
  9. Rotary

    Rotary Senior member

    Joined:
    Apr 10, 2003
    Messages:
    8,353
    Likes Received:
    0
    Trophy Points:
    116
    hi

    just a thought here but you arnt running out of disc are you? try shrinking the compression size 30 meg smaller!
     

Share This Page