1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Shrink DVD burning error

Discussion in 'DVD Shrink forum' started by RJRon, Sep 22, 2004.

  1. RJRon

    RJRon Member

    Joined:
    Jun 1, 2003
    Messages:
    6
    Likes Received:
    0
    Trophy Points:
    11
    I tried Shrink DVD for the first time to backup a DVD that would require significant compression. I liked the fact that I could exclude the audio tracks I wouldn't use (i.e., French, Spanish, etc.) and improve the need for compression on the main title. The setup and decoding seemed to go fine, and I left the actual burning unattended overnight. When I checked the next morning I saw the message that the burn had failed (fairly quickly into the project). I was hoping someone with more experience with Shrink DVD could help me understand the error message and what to do to fix it. The entire error message was quite lengthy, but I think I can identify the point it went bad...

    11:50:13 PM #17 Phase 36 File APIProgress.cpp, Line 273
    Burn process started at 4x (5,540 KB/s)

    11:50:13 PM #18 Text 0 File ThreadedTransferInterface.cpp, Line 2344
    Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

    11:50:13 PM #19 Text 0 File DVDR.cpp, Line 1879
    Recording mode: Sequential Recording Mode

    11:50:13 PM #20 Text 0 File Mmc.cpp, Line 20401
    Set BUFE: Power-Burn -> ON

    11:50:13 PM #21 Text 0 File DVDR.cpp, Line 2020
    Start write address at LBA 0
    DVD high compatibility mode: Yes

    11:50:13 PM #22 Text 0 File Cdrdrv.cpp, Line 8128
    ---- DVD Structure: Physical Format Information (00h) ----
    Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
    Book Type: DVD-R (2), Part Version: 5
    Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
    Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
    Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
    Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
    End Physical Sector Number of Data Area: 0 h
    End Sector Number in Layer 0: 0 h
    Data in Burst Cutting Area (BCA) does not exist
    Start sector number of the current Border-Out: 0 h
    Start sector number of the next Border-In: 0 h
    Media Specific [16..63]:
    00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
    00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
    00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................

    11:50:18 PM #23 Text 0 File Cdrdrv.cpp, Line 1294
    23:50:18.687 - SONY DVD RW DRU-500A\H0 T0 : Queue again later

    11:53:18 PM #24 CDR -25 File Writer.cpp, Line 304
    Queue again later
    SONY DVD RW DRU-500A\H0 T0

    11:53:18 PM #25 Text 0 File ThreadedTransfer.cpp, Line 229
    all writers idle, stopping conversion

    11:53:18 PM #26 Text 0 File ThreadedTransfer.cpp, Line 223
    conversion idle, stopping reader

    11:53:18 PM #27 Text 0 File DVDR.cpp, Line 2256
    EndDAO: Last written address was 2239

    11:53:28 PM #28 Phase 38 File APIProgress.cpp, Line 273
    Burn process failed at 4x (5,540 KB/s)

    11:53:28 PM #29 Text 0 File AudioCompilationImpl.cpp, Line 828
    DRM: DRM burn session terminated.

    11:53:28 PM #30 Text 0 File AudioCompilationImpl.cpp, Line 857
    DRM: Closing entire DRM handling. Bye.
     
  2. RJRon

    RJRon Member

    Joined:
    Jun 1, 2003
    Messages:
    6
    Likes Received:
    0
    Trophy Points:
    11
    OK, so I read in another thread that some people were having problems when Shrink DVD was burning the DVD too close to full... something about poor material quality close to the edge. So I re-encoded from the files Shrink DVD left on my HD and reduced just slightly more (compressed further) the size of a couple of items I didn't care too much about (menus, bonus sets, etc.) and this time it burned fine. It would still be nice to know what the error log in my original post indicated the problem was, but in the mean time I was able to successfully back up my new Star Wars IV... now on to the next two disks.
     
  3. ddlooping

    ddlooping Active member

    Joined:
    Apr 29, 2003
    Messages:
    1,013
    Likes Received:
    0
    Trophy Points:
    66
    Hi RJRon. :)

    It could be the burning process failed because of an excessive write speed for your media/burner combination. ;)
     
  4. cynthia_

    cynthia_ Regular member

    Joined:
    Sep 10, 2004
    Messages:
    312
    Likes Received:
    0
    Trophy Points:
    26

Share This Page