hi all this is a teaser that i am really stcuk with with regards to the problem i am having.copying DVD's . i down loaded windows classic player and this seems to have resolved my viewing of DVD films.as my windows meadia player started to not play dvd's..keeps telling me to alter the screen settings but still having problems copying them....as it stands now.. i can copy the film using decryptor no probs. but when i try to copy to disc.its starts off ok then just stops copying.resulting in wasted DVD disc every time. so you can see i am stuck. dvd type laser product model number sohw-16325 lite-on ot corp i have removed the writer and rerun my pc replaced the writer still having problesm disc type emtec 4.7 gb recordable but i know this is not the root cause as i have used these discs many times. is it worth re installing windows to resolve the problem my dvd writer starts to copy discs then it seems to stop copying if you can help it would be much abliged thank you all
hi i would still plum for the media used may be the fault? use dvdinfo pro to find out the id codes on good ones burnt and a disc that bombs out on you see if there the same id code!... but also do you have the latest firmware in your drive? you sure that drive number is correct? sohw-16325 ? http://forum.rpc1.org/dl_firmware.php?category=4&manufactor=17 ============================= also go through this lot dont miss any out! 1. Running Programs Make sure you quit all running background programs, such as anti-virus software. Windows 95 Users Use the Ctrl-Alt-Del function to quit all the programs using the Task Manager, EXCEPT for the Explorer, systray, and your recording software Windows 98/ME Users Select [Start] -> [Run], then input "msconfig". Disable everything under the [Startup] tab, except "system tray'. Windows 2000/XP Users Open the Task Manager, then select the program/s under the [Application] tab, then click [End Task]. 2. Drive Connection Other devices may be interfering with the CD-R/RW drive. Disconnect all other removable devices, then try recording again. If there is still a problem, try the following. Optimal Hardware Configuration All hard drives are placed on the Primary IDE, check that the drives are correctly set as master/slave. CD-ROM/CD-R/RW drives are placed on the Secondary IDE, set the recording drive as the "master". If you are using a USB or IEEE devices, disconnect them. Update your chipset Windows 95/98/ME Users Right click on [My Computer] and select [Properties] from the menu. Click on [Device Manager], then click to open [Hard Disk Controllers]. You will find: the Primary IDE Channel controller, the Secondary IDE Channel controller and a brand name controller, e.g. Intel, SIS, VIA, etc. The brand name controller is what needs to be updated. Please visit their website to obtain these updates. Windows NT/2000/XP Users Right click on [My Computer] and select [Properties] from the menu. Click [Device Manager] on the [Hardware] tab, then click to open the [IDE ATA/ATAPI (hard disk) controllers] section. You will find: the Primary IDE Channel controller, Secondary IDE Channel controller, and a brand name controller, e.g. Intel, SIS, VIA, etc. The brand name controller is what needs to be updated. Please visit their website to obtain these updates. Configure Windows Make sure that your operating system has been fully updated. Visit the Microsoft website to acquire these updates. 3. ASPI Manager Check your ASPI layer configuration. Your recording program is likely to use the standard windows ASPI layer, which has been replaced by another ASPI layer of yet another recording program. Make sure you have the original windows ASPI layer in use and retry. If the problem persists, contact the drive maker. 4. DMA Settings Setting DMA mode: Windows 95/98/ME Users Right click on [My Computer] and select [Properties] from the menu. Click on [Device Manager], then click on [CD-ROM]. This will expand to show the CD drives on your system. Right click on a drive and select [Properties] from the menu. Click on the [Settings] tab and check that the [DMA] option is enabled. Repeat this procedure for the remaining CD drives. Win NT/2000/XP Users Right click on [My Computer] and select [Properties] from the menu. Click [Device Manager] on the [Hardware] tab, then click to open the [IDE ATA/ATAPI (hard disk) controllers] section. You will find: the Primary IDE Channel controller, Secondary IDE Channel controller. Complete the following procedure: Right click on the Primary IDE controller and select [Properties] from the menu. Select the [Advanced Settings] tab. Check that the [Transfer Mode] for both devices is set to [DMA if available]. Repeat this for Secondary IDE controller. Note: In some cases older CD-ROM drives will not support DMA mode. In that case please set both devices to PIO mode. 5. Disc Recording errors often occur when the disc is dirty, or has fingerprints or scratches. If an error occurred during test simulation (before actual recording), clean the disc. If you are getting recording errors, try the following. Use a different blank, recordable disc. Use a different manufacturer's disc. Ensure the disc is clean before recording: Remove all fingerprints, dirt, and dust from the shiny side of your disc using a nonabrasive cloth with a mild, nonabrasive soap solution. Wipe the disc from the center to the edge of the disc. Dry the disc completely. Error during file verification If an error occurred when the files were being verified, record the same files again using a different disc. Read error when copying a disc When copying a disc, if an error occurred while reading data from the original disc, the original disc may be scratched or dirty. Try cleaning the disc. Remove all fingerprints, dirt, and dust from the shiny side of your disc using a nonabrasive cloth with a mild, nonabrasive soap solution. Wipe the disc from the center to the edge of the disc. Dry the disc completely. Try using a different source drive. To change the drive you use to read your disc, click the Change button when asked to insert a source disc into your drive tray. Select the drive you wish to use from the drop-down menu. Insert your disc into the new drive. Try using copying the disc using one drive as both the source and destination drive. When you use your recorder to both read and write to your disc, B's Recorder GOLD creates an image file of the entire disc to your hard drive and then copies that temporary file onto your blank disc. This can be helpful if the drive you are using to read your original disc is slow or unreliable. If the problem persists, contact the drive maker. 6. Drive If you have tried Actions 1 through 5 above, there may be a problem with your drive. Contact the drive maker with details of the error code. If the 5th and 6th digit of the error code is 80 through FF, then the error code is maker unique. The descriptions of these error codes differ depending on the maker.
@bobs928, Just out of curiousity, what movie are you trying to back up? You'll need to copy your log error with DVD Decrypter and post or paste it in here, so other members will be able to help you better. No offense...and I really mean it, but this sounds like a crap media to me. Additionally, your DMA may have gone from "DMA if available" to "PIO" mode. It's worth to take a look at your "Device Manager" and reset it back to DMA. To enable DMA back on, this is if you have Win2000 or XP, follow this link http://www.burstcopy.com/dma/xp/ - I'm sure it'll at least help you somthing, not now, but perhaps in the future. Just a note: please use good medias such as FUJI/TY, Verbatim, Maxell and SONY when backing up DVD movies or PS2 games, and make sure it says; "Made In Japan". You won't regret getting these highly recommended quality medias in the near future. Of course they're the best in the market now-a-days and they're highly recommended by the most knowledgeable members in AfterDawn.com at the "DVD-R/+R Forum" as well.
