DVD SHRINK 3.2 to Nero 6.6018

Discussion in 'Nero discussion' started by MARTY, Feb 25, 2006.

Thread Status:
Not open for further replies.
  1. MARTY

    MARTY Member

    Joined:
    Feb 22, 2006
    Messages:
    21
    Likes Received:
    0
    Trophy Points:
    11
    Well this is my next problem, i have sorted out getting Shrink to fire up Nero 6.6.018 but it trys to burn at 16 x and the only place before it asks for a disc makes no difference if i change it besides it only shows Maximum, 2.4 1.0 or something like that ??

    So what gives as it doesnt like 16 x and fails the burn every time.
     
    MARTY, Feb 25, 2006
    #1
  2. gwendolin

    gwendolin Senior member

    Joined:
    Jun 29, 2005
    Messages:
    7,447
    Likes Received:
    0
    Trophy Points:
    116
    @Marty, I'm sure in your last thread you wer advised to burn at 4X, nobody burns at 16X unless they want the burn to FAIL. I have also answered your other thread.
     
    gwendolin, Feb 25, 2006
    #2
  3. whompus

    whompus Active member

    Joined:
    Dec 2, 2002
    Messages:
    1,346
    Likes Received:
    0
    Trophy Points:
    66
    To do so manualy with shrink and nero in conjunction change the settings. In shrink when you click on backup the window pops up to select target and such. Make it look like this and it should remain unless you change it later.

    [​IMG]
     
    whompus, Feb 25, 2006
    #3
  4. binkie7

    binkie7 Moderator Staff Member

    Joined:
    Feb 12, 2005
    Messages:
    17,588
    Likes Received:
    0
    Trophy Points:
    116
    @MARTY
    If your ripping and burning from the same drive - shrink will only give your the burn speeds of the disc in the drive or max. So if you have a dvd-rom you will see 1x,2x,2.4x & max.
    Rip from another drive and have a blank in the drive your using to burn - then it will give you the supported burn speeds of the blank.
     
    binkie7, Feb 25, 2006
    #4
  5. whompus

    whompus Active member

    Joined:
    Dec 2, 2002
    Messages:
    1,346
    Likes Received:
    0
    Trophy Points:
    66
    Or if you only have the one drive. Open files from hard drive with blank disk in the drive to make the settings with. Then the settings should be there the next time as long as you don't change them.

    @binkie7...Or does shrink change the settings with each rip? Its been a long time for me of not using shrink.
     
    Last edited: Feb 25, 2006
    whompus, Feb 25, 2006
    #5
  6. binkie7

    binkie7 Moderator Staff Member

    Joined:
    Feb 12, 2005
    Messages:
    17,588
    Likes Received:
    0
    Trophy Points:
    116
    If your only using the 1 drive it only lists the burn speeds for the disc/dvd that is being ripped and max - it won't keep the last speed used like it does if using 2 drives.
    Another way around the 1 drive bit is to autoburn w/ decrypter - you can set the burn speed 1st then shut down decrypter - decrypter let's you pick any speed even if no disc is in the drive.
    I still use shrink occasionally- just depends what protection the disc has.
     
    binkie7, Feb 25, 2006
    #6
  7. whompus

    whompus Active member

    Joined:
    Dec 2, 2002
    Messages:
    1,346
    Likes Received:
    0
    Trophy Points:
    66
    Hmmm...Thats good to know. I guess I never know that. As you can see from my settings selection in the pic I posted. Those speeds are with no disk in the burner. But then I have always used hacked burners. If a burners actions can not be changed by the user then they just don't get my $.
     
    whompus, Feb 25, 2006
    #7
  8. binkie7

    binkie7 Moderator Staff Member

    Joined:
    Feb 12, 2005
    Messages:
    17,588
    Likes Received:
    0
    Trophy Points:
    116
    I just checked shrink - no disc in drive and I didn't get those speeds your listed on one drive but the other one I did. Interesting - learn something new!
    I checked the 1 drive thing again w/ both drives and same thing - only lists the dvd-rom speed (1x,2x,2.4x) and max.
    Both drives are unhacked though - Pioneer and Liteon -latest firmware though.
    I like your stmt about not being able to change the burners action = not getting $.
     
    binkie7, Feb 25, 2006
    #8
  9. whompus

    whompus Active member

    Joined:
    Dec 2, 2002
    Messages:
    1,346
    Likes Received:
    0
    Trophy Points:
    66
    Yup...Pioneer, Liteon, and Benq and there clones are all I use.
     
    whompus, Feb 25, 2006
    #9
  10. creaky

    creaky Moderator Staff Member

    Joined:
    Jan 14, 2005
    Messages:
    27,900
    Likes Received:
    1
    Trophy Points:
    96
    creaky, Feb 25, 2006
    #10
Thread Status:
Not open for further replies.

Share This Page