Eurovox TX problem (boot, F_00, UA_C, CHd )l

Discussion in 'Digital TV - UK & Europe' started by BenE123, Apr 11, 2008.

  1. BenE123

    BenE123 Member

    Joined:
    Apr 10, 2008
    Messages:
    10
    Likes Received:
    0
    Trophy Points:
    11
    Originally posted by mochara: Hi There Folks, I have just received a EuroVox TX DVB and tried to load some software to it. E_Vox_TX C____S Ireland MMDS. It appeared to to be sucessfull. However thereafter when I repowered it I got the following. boot, F_00, UA_C, CHdl. at this point it appears frozen and the remote does not have any effect. Can you point me in the right direction? Prior to this I was receiving the standard channels through the box. Rgds

    _
    BenE123
    Newbie
    _ 11. April 2008 @ 09:49 _ Link to this message Edit message
    mochara, Just saw your post and I'm hoping you can help me. I have just bought the Eurovox TX and I am seeing the same symptoms as you on initial power up. No response from the remote or anything. Did you get any resolution for this issue or can anybody else offer advice???? Thanks in advance
     
    BenE123, Apr 11, 2008
    #1
  2. BenE123

    BenE123 Member

    Joined:
    Apr 10, 2008
    Messages:
    10
    Likes Received:
    0
    Trophy Points:
    11
    The solution to all issues can be found on Eamos FTA library.
    http://eko.4shared.com/

    The Eurovox TX problem (boot, F_00, UA_C, CHd )issue is is caused by a bad flash. To resolve go to Eamos FTA Library (link above) and download EV_TX_CHLD_FIX_rev03.zip. Unzip and flash your TX box. Helpful txt files here also. This will resolve the issue and then flash the box with EVX_TX_H_071123.bin and its ROCK & ROLL.

    Thanks again to everyone on Afterdawn who posted a reply. Eamos "you d man"
     
    BenE123, Apr 28, 2008
    #2
  3. sc0user

    sc0user Senior member

    Joined:
    May 31, 2007
    Messages:
    13,111
    Likes Received:
    0
    Trophy Points:
    116
    Sorry Ben missed your post I put it in there a while back. But Eamo is still the man alright :)
     
    Last edited: Apr 28, 2008
    sc0user, Apr 28, 2008
    #3
  4. BenE123

    BenE123 Member

    Joined:
    Apr 10, 2008
    Messages:
    10
    Likes Received:
    0
    Trophy Points:
    11
    No worries sc0user your the other man. It seems that you and a few other dedicated dudes go out of your way to try and solve every issue. Top marks for that. I may need your assistance again cos I'm currently going through your threads to try and get all the channels up as I only have 3 or 4 channels working. Looks like I have some issue related to setting the EMU key. Keep up the good work.
     
    BenE123, Apr 28, 2008
    #4
  5. bloggo3

    bloggo3 Member

    Joined:
    Nov 16, 2007
    Messages:
    25
    Likes Received:
    0
    Trophy Points:
    11
    you're right about scOuser being the other man. the amount of posts from him is phenomenal.
    a friend has a euro-vox that doesn't seem to power on at all. can anyone tell me if it can be salvaged or is it for the skip.
     
    bloggo3, Apr 28, 2008
    #5
  6. BenE123

    BenE123 Member

    Joined:
    Apr 10, 2008
    Messages:
    10
    Likes Received:
    0
    Trophy Points:
    11
    Bloggo3 try running the sequence of events in the thread above. My box did nothing except run through the following LED display codes (boot, F_00, UA_C, CHd ) I ran the EV_TX_CHLD_FIX_rev03 sequence and reflashed again with EVX_TX_H_071123.bin file and it worked fine. If you have nothing at all i.e. no power try checking the fuse or replace the power cable.
     
    BenE123, Apr 29, 2008
    #6

Share This Page