[GUIDE]:UPMS-V4 (Sapphire) Installer **DO NOT USE WITH CFW 4.01M33 AND ABOVE!!**

And you say it works fine on your fat psp? You do have the multi-IPL and the trio installed on the memory stick, right?

With the UPMS and battery inserted in the fat psp-try changing the folder to DCv3, then remove the battery and UPMS and put it into the slim psp as per the instructions, and see if that works for you.

 

yeah i have the multi ipl and trio thing and the patch installed on the memory stick.

how do i change the folder or whatever to the DVc3?

 

From the Ultimate Loader menu (or the main menu)-switch it to DCv3, the remove the battery/memory stick and then put it in the slim and see if that works.

 

it doesnt work for the fat now that i switched it to the DVC3
does the same thing the slim did.
roar whats going on lol....

thanks for your help so far i really appreciate it. ill try reloading all the files...

and then switch it to DVC3

if switching to DVC3 doesnt work, what do u suggest i do?

after i switched it to DVC3 i dont see anything for either again.

 

Just to clear this up for you guys. The 3.52 update folder is straight from DAX's site. The 1.50 downgrade and the kxploit patch are part of Hellcat's Menu and are executed by it. You can use any CFW installer you like. Just make sure it is for a 1.50 to CFW install. I just supplied 3.52 because it was the newest(other than 3.71 which is in DCv3) and what I use. Go ahead give a new one a try. I just had no longing for older CFW so like I said I just used 3.52. So add as many as you like just set the option to save the path for the one you want to use.

And for slim boot on this version of trio.
The following is done with no battery inserted.

1. Push power button down to hold, so yellow dot shows.
2. Insert you Magik Stick.
3. Hold left trigger if you have installed Multi-IPL
4. Insert your JigKick battery into the slim, keep left trigger held until the Slim turns off. You will hear the slim start up.
5. Remove your JigKick battery, push hold key up, so now yellow dot shows.
6. Hold left trigger again and insert the JigKick battery.
The memstick light will blink after about 5 seconds, then you can release the trigger.

There is no way for a Slim to display the Hellcat and Joker Menus. They are based on 1.50 FW and will only display on a Phat. This is why we have implemented the Slim boot method. It will take you to only DCv3.


One more thing. The 340.pbp is only used for the installation of DCv3. Once you run the CSO to install ULoader and the other Menus it can be deleted.


Don't get me wrong dEEz has done us a great credit here, but this is why I have suggested you folks visit the official forum. I don't get here real often and I'm probably the only team member you will see here. Due come visit if there is something you guys are stumped on.

 

i tried to do what u said with the hold and all that but i still get a black screen on my slim psp

when do i take the hold off? you guys say it at the end and ihave no idea when to take hold off.

 

Edited last post to make it a little more clear for the slim boot.

 

i did everything you told me too but the only thing that is different is
my ORANGE memory stick light NEVER flashes ever on the psp SLIM.

 

You are not leaving the hold switvh on for the entire process. It should not be returned to it's normal position untill you are presented with the DCv3 menu.

Also make sure you release the L trigger when the MS light becomes active.

 

but how long does it take to get to DVC3? cause after 2 mins im still holding the L trigger with no orange light ever going off.

 

OK
Make sure you follow the steps exactly as I have writen them.
Try releasing the L button when the screen lightens up. (starts to turn on) This is what I have to do as my MS light is hard to see cuz I have a skin on my PSP.

 

Hello Everybody

I have a PSP 1001 aka PSP Phat and PSP 2000 aka PSP Slim-N-Lite.
I am planning to upgrade my PSP Slim to 3.71M33 firmware using your guide.

Will it repartition the Memory Stick via PSP ?

While i was preparing the Memory Stick i didn't set the game kernel to 3.52-M33 in my PSP Phat.
The game kernel currently is 1.5.


Though the UPMS Installer correctly placed all the softwares in Game352 folder and the Memory Stick preparation process has been successfully finished.

Is the game kernel setting really important?
Shall i start over the Memory Stick preparation process from the beginning after changing Game kernel setting?

Please advise me

Also it would nice if you add procedure to upgrade Slim's 3.60 OFW to 3.71M33 using Despertar del Cementerio v3,
Because most of the visitors will be searching only for that kind of procedure after converting their Battery to service mode using your guide,

Finally do i need to reset to factory settings after install 3.71 M33?

 

I got a quick question, This works well with phat psp's but for a slim would I just run Despertar del Cementerio v3 and I'm done? And this would get me to 3.72m33-2?

 

Yes you are correct.

For the slim though make sure your battery is in correctly otherwise you will get a black screen even though you get a green power light.

I had this today on my Slim while testing the next release.

 

I'm using a fat to enable a slim, and I'm getting as far as step #3 (I already have a pandora battery so I'm skipping Step #2 completely) when I get a message saying:
"ERROR WHILE INITIALIZING: 0x8ca10002". This is when I try to install Ultimate Loader (Trio). Am I doing something wrong?

 

Make sure you installed the 'Multi-IPL' in step #1

 

Ok, one last question. I've got it all set up, I've got the UPMS and the Pandora Battery, and I'm trying to get DvC3 on my slim. I insert the MS and then then battery, holding down L until the screen flashes, then letting go of L. the screen goes back to dark and nothing shows up, but I can still hit SELECT to shut down the PSP. What do I do?

 

Never mind, it all worked out. thanks for the awesome APP!

 

Alright, I got a fat psp with the xbox 360 theme. Do I have to do anything before using Despertar del Cementerio v3 or can I just go ahead and install 3.71m33 and then the addon? Will it overwrite the theme?

 

If you're using a manually flashed theme then changing the flash will obviously erase your current flash. So yeah.