[GUIDE]:UPMS-V4 (Sapphire) Installer **DO NOT USE WITH CFW 4.01M33 AND ABOVE!!**

SUPER-UBER-NOOB Q- can i unbrick my psp with this???

 

Thanks for the advice Deez..

But before i try this again....it will definitely work on 3.71ofw slim?? my friends getting a bit nervous and protective of his new slim!!

Also, you say to name firmware files without the extra dot as in guide ie -
you say - 340.PBP
Guide says 3.40.PBP ??

Soz to be a pain, if is was mine i'd keep trying til i figured it out!

Thanks for the help!!!!!!

Alun

 

Yes and Upgrade CFW to either 3.52 m33 or 3.71 M33 inc updates.

 

340.PBP not 3.40.PBP

Also there is a new release that don't require 340.PBP only 150.PBP and 371.PBP

Backup the Nand of your friends PSP before doing anything. This is really important, because if anything goes wrong this will be the only way to recover it.

 

Not a problem, and thanks for noticing that typo in the guide-

Just to clarify: The eboots should be named as follows-
UPDATE.PBP
150.PBP
340.PBP
371.PBP

I have corrected this in the original post also for future reference.

Thanks!

 

my sleep mode dont work.
psp always go to hard reset when i sleep my psp while playing GAME.
so,how to recover it?
please help..

 

I managed to create a UPMS and battery and it works on my friend's PSP Fat. However, it doesn't work on my PSP Slim and Lite that runs 3.71 official. Seeing how other people were having trouble, I was going to start all over and try some other method, so I used the Joker Menu's Pandora Battery Creator and made the battery "normal" again. For some reason though, my friend's PSP won't start up. The light goes on but the screen remains blank. What should I do?

 

if you want to use the UPMS in slim psp,make sure the DC3 is the active folder.Your slim may turn off depending on what folder is active on memory stick at the time, this is normal for the slim.

If you have either Hellcat or Joker folders active at the time of doing the slim, then the slim will turn off,just remove the battery again, put HOLD back to normal then hold left trigger and insert your battery, this will display the Ultimate Loader menu. From here you can launch DCv3.

If you have the Hold switch on and insert battery while holding Left Trigger it will boot directly to DCv3, but don't forget to put hold switch back to normal otherwise your button presses will not work.

 

hmm, but that still doesn't answer my main problem... i made the battery "normal" again, but now, i think my friend's psp got fully bricked... i won't ask how i should fix this, but what did i do wrong? i will admit, the wifi switch was on and tried to run DC3 and install 3.71 M33 on the fat before running the 1.50 kernel patch... is that what did it?

 

are you sure that battery is normal again?
did you backup the eeprom before convert the battery?
if psp automatically on when you pop the battery in,maybe it still in service mode.

 

i'm sure it's not the battery... there's a eeprom.bin left on my memory stick, the psp said the battery was normal again, it charges, and the psp refuses to turn on after i turned off the psp once. i would test the battery with my psp, but you know what's worse than a bricked psp is two bricked psp's...

 

try to turn on the psp without battery.just use AC adapter.if psp turn on well,the psp is not brick but maybe you hv battery prob.if not,i hv no idea about it.

 

Elo every1 i jus lyk 2 ask is there a way 2 create a magic memory card without a homebrew enabled psp (using a pc nd a card reader) i have a hardmod bettery there4 i don't want 2 make another 1 ie I only want da magic card plz help how do i go abt doing jus dat

 

http://forums.afterdawn.com/thread_view.cfm/591203

 

yipppeeeeeeeeeeeeeeeeeeeee!!

3.71 ofw slim ------> 3.71 M33-2

Straight out the box, job done thanks for your help guys, keep it up!!!!

(Had to use the hold button in the end to get to menu...)

thank you, thank you, thank you!!!!!!!!!!!

 

links is broken can i please have the installer

 

Updated link in original post-Please note that this is the most recent version (Emerald) that you are downloading and the steps will differ slightly in the installer from the guide I originally posted.Please have a look at the first post of this thread at the bottom-I have included the changes and revisions.

 

removed edited forum rules

 

advertising is againest the rules