how to remove waranty stikers?,help

Discussion in 'Nintendo Wii / Wii U' started by bosanci28, May 3, 2008.

  1. bosanci28

    bosanci28 Member

    Joined:
    Oct 12, 2007
    Messages:
    49
    Likes Received:
    0
    Trophy Points:
    16
    is there a way or trick how to remove the waranty stickers from the wii?
    maybe some pictures where exactly they are?,,
    so the waranty does nt get void...
    thanks
     
    bosanci28, May 3, 2008
    #1
  2. penguin98

    penguin98 Regular member

    Joined:
    Nov 26, 2006
    Messages:
    2,706
    Likes Received:
    0
    Trophy Points:
    46
    They're putting warentee stickers on wii's now?

    I have a launch wii and there were no warentee stickers on it.
     
    penguin98, May 3, 2008
    #2
  3. sparky22

    sparky22 Member

    Joined:
    Apr 10, 2008
    Messages:
    33
    Likes Received:
    0
    Trophy Points:
    16
    There is no warrenty stickers as such, just the white pads over the screws.

    Sharp knife does the trick :)
     
    sparky22, May 3, 2008
    #3
  4. penguin98

    penguin98 Regular member

    Joined:
    Nov 26, 2006
    Messages:
    2,706
    Likes Received:
    0
    Trophy Points:
    46
    Oh, the white screw cover stickers.

    I couldnt get those to restick after modding the wii so my screws are still exposed. I also ended up with an extra screw after putting it back together and was never able to figure out where it belonged. But everything works great so I cant complain.
     
    penguin98, May 3, 2008
    #4
  5. bosanci28

    bosanci28 Member

    Joined:
    Oct 12, 2007
    Messages:
    49
    Likes Received:
    0
    Trophy Points:
    16

    thanks
     
    Last edited: May 3, 2008
    bosanci28, May 3, 2008
    #5
  6. sparky22

    sparky22 Member

    Joined:
    Apr 10, 2008
    Messages:
    33
    Likes Received:
    0
    Trophy Points:
    16
    What does the screw look like and I'll tell you where it goes ;)

    There is some places on line sell new sticker/pad sets.

    Just incase this is usefull to anyone heres whats needed to open the wii.... You'll need a small phillips and triwing screw driver set, Like this

    1 - Remove the 2 flaps
    2 - Under the flaps is a black face plate, in there is 3 tiny phillips screws. Remove them and the face plate
    3 - Under the black face plate you will find 2 x silver triwing screws, remove them.
    4 - On the other side (battery side) remove the battery and reveal a silver triwing screw. Remove that.
    5- On the same side, lift the rubber pad at the front to reveal a small black phillips screw - remove that.
    6- Again on the same side along from the batter cover is a white square sticker, remove the sticker to reveal a silver triwing screw. Remove that.
    7- On the underside of the wii there is 2 rectangle rubber pads at the back, remove them to reveal 2 x silver triwing screws. Remove them.
    8- On the same side near the front is 2 x rectangle white stickers, remove them to reveal 2 x black triwing screws, remove them.
    9- The front panel will now come off, watch for the wire that will need unplugged.
    10 - The case will now pull apart and you'll see the drive.
    11 - To remove the drive you'll need to remove the small silver screw in each corner using a small phillips driver.
    12 - Once the screws are out, caefully remove the drive. 1 cable will need unplugged, the other is a ribbon cable. To remove the ribbon cable, open the little flap on the connector.

    Happy Days.
     
    sparky22, May 4, 2008
    #6

Share This Page