1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Imgburn Error codes

Discussion in 'DVD±R for advanced users' started by Cappy66, Dec 23, 2007.

  1. Cappy66

    Cappy66 Member

    Joined:
    Dec 20, 2007
    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    11
    While trying to burn image from Imageburn I get an error that states:
    I/O Error!

    Device: [5:1:0] LITE-ON DVDRW LH-20A1HLL0C (F:) (ATA)


    ScsiStatus: 0x02
    Interpretation: Check Condition

    CDB: BF 00 00 00 00 00 00 20 00 0C 00 00
    Interpretation: Send DVD Structure - DVD+R DL Boundry Information

    Sense Area: 70 00 03 00 00 00 00 0A 00 00 00 00 73 03 00 00 00 00
    Interpretation: Power Calibration Area Error



    Retry Cancel
    I recieved the same error while using DVD DEcrypter. Recently replaced the drive. Recently applied System restore. Please help.
     
  2. pryme_H

    pryme_H Regular member

    Joined:
    Mar 13, 2006
    Messages:
    1,715
    Likes Received:
    0
    Trophy Points:
    46
    Cappy66,
    First off, check to see if there is an update to your burner firmware. Secondly, even with the error pop up, allow 30 seconds or more and then click on "Retry" to see if it'll commence with with the burn. It'll also help if you provide a copy of the log. To do so,
    Open ImgBurn=>Click Help and then select ImgBurn logs=>Open the Txt Doc. The newest record should be the first one.
     
  3. 7thsinger

    7thsinger Regular member

    Joined:
    Oct 17, 2007
    Messages:
    3,605
    Likes Received:
    2
    Trophy Points:
    48
    To add to pryme_H's good advice, i'd also add that if you're using DvdDecrypter it might be time to upgrade. As good a program as it was, it's no longer updated and therefore will have trouble with newer titles.
    Get DvdFab Hd Decrypter (freeware) then use DvdShrink, then ImgBurn. You'll have better luck that way.

    BTW, what title are you trying to back up?
     
  4. Cappy66

    Cappy66 Member

    Joined:
    Dec 20, 2007
    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    11
    Firmware installed was the most current according to LITE-ON. Tried the retry button many times, but each time came up with the original error. I fimally had to abort the program. The following is the error report:

    ; //****************************************\\
    ; ImgBurn Version 2.3.2.0 - Log
    ; Tuesday, 25 December 2007, 09:13:00
    ; \\****************************************//
    ;
    ;
    I 07:14:39 ImgBurn Version 2.3.2.0 started!
    I 07:14:39 Microsoft Windows XP Media Center Edition (5.1, Build 2600 : Service Pack 2)
    I 07:14:39 Total Physical Memory: 981,484 KB - Available: 576,876 KB
    W 07:14:39 Drive D:\ (FAT32) does not support single files > 4 GB in size.
    W 07:14:39 Drive N:\ (FAT32) does not support single files > 4 GB in size.
    I 07:14:39 Initialising SPTI...
    I 07:14:39 Searching for SCSI / ATAPI devices...
    I 07:14:39 Found 2 DVD±RW/RAMs!
    I 07:17:25 Operation Started!
    I 07:17:25 Source File: C:\Bourne\THE_BOURNE_ULTIMATUM.MDS
    I 07:17:25 Source File Sectors: 4,119,893 (MODE1/2048)
    I 07:17:25 Source File Size: 8,437,540,864 bytes
    I 07:17:25 Source File Volume Identifier: THE_BOURNE_ULTIMATUM
    I 07:17:25 Source File Implementation Identifier: Daikin U.S. Comtec Lab
    I 07:17:25 Source File File System(s): ISO9660, UDF (1.02)
    I 07:17:25 Destination Device: [5:0:0] LITE-ON DVDRW SHM-165H6S HP10 (E:) (ATA)
    I 07:17:25 Destination Media Type: DVD+R DL (Disc ID: RICOHJPN-D01-02) (Speeds: 4x, 6x, 8x)
    I 07:17:25 Destination Media Sectors: 4,173,824
    I 07:17:25 Write Mode: DVD
    I 07:17:25 Write Type: DAO
    I 07:17:25 Write Speed: 4x
    I 07:17:25 Link Size: Auto
    I 07:17:25 Test Mode: No
    I 07:17:25 BURN-Proof: Enabled
    I 07:17:25 Optimal L0 Data Zone Capacity: 2,063,120
    I 07:17:25 Optimal L0 Data Zone Method: Copied From Original Disc
    I 07:34:17 Filling Buffer... (20 MB)
    I 07:34:20 Writing LeadIn...
    W 07:35:39 Failed to Write Sectors 0 - 31 - Power Calibration Area Error
    W 07:35:39 Retrying (1 of 20)...
    W 07:36:56 Retry Failed - Power Calibration Area Error
    W 07:36:56 Retrying (2 of 20)...
    W 07:38:03 Retry Failed - Power Calibration Area Error
    W 07:38:03 Retrying (3 of 20)...
    W 07:39:13 Retry Failed - Power Calibration Area Error
    W 07:39:13 Retrying (4 of 20)...
    W 07:40:29 Retry Failed - Power Calibration Area Error
    W 07:40:29 Retrying (5 of 20)...
    I 07:41:30 Abort Request Acknowledged
    W 07:41:49 Retry Failed - Power Calibration Area Error
    W 07:41:49 Retrying (6 of 20)...
    W 07:42:55 Retry Failed - Power Calibration Area Error
    W 07:42:55 Retrying (7 of 20)...
    W 07:44:07 Retry Failed - Power Calibration Area Error
    W 07:44:07 Retrying (8 of 20)...
    W 07:45:30 Retry Failed - Power Calibration Area Error
    W 07:45:30 Retrying (9 of 20)...
    W 07:46:43 Retry Failed - Power Calibration Area Error
    W 07:46:43 Retrying (10 of 20)...
    W 07:47:53 Retry Failed - Power Calibration Area Error
    W 07:47:53 Retrying (11 of 20)...
    W 07:49:02 Retry Failed - Power Calibration Area Error
    W 07:49:02 Retrying (12 of 20)...
    W 07:50:19 Retry Failed - Power Calibration Area Error
    W 07:50:19 Retrying (13 of 20)...
    W 07:51:28 Retry Failed - Power Calibration Area Error
    W 07:51:28 Retrying (14 of 20)...
    W 07:52:34 Retry Failed - Power Calibration Area Error
    W 07:52:34 Retrying (15 of 20)...
    W 07:53:40 Retry Failed - Power Calibration Area Error
    W 07:53:40 Retrying (16 of 20)...
    W 07:54:46 Retry Failed - Power Calibration Area Error
    W 07:54:46 Retrying (17 of 20)...
    W 07:55:55 Retry Failed - Power Calibration Area Error
    W 07:55:55 Retrying (18 of 20)...
    W 07:57:11 Retry Failed - Power Calibration Area Error
    W 07:57:11 Retrying (19 of 20)...
    W 07:58:30 Retry Failed - Power Calibration Area Error
    W 07:58:30 Retrying (20 of 20)...
    W 07:59:39 Retry Failed - Power Calibration Area Error
    E 08:04:52 Failed to Write Sectors 0 - 31 - Power Calibration Area Error
    I 08:04:52 Synchronising Cache...
    I 08:04:53 Closing Track...
    I 08:04:54 Finalising Disc...
    E 08:04:55 Failed to Write Image!
    E 08:04:55 Operation Aborted! - Duration: 00:47:29
    I 08:04:55 Average Write Rate: N/A - Maximum Write Rate: N/A
    I 09:13:00 Close Request Acknowledged
    I 09:13:00 Closing Down...
    I 09:13:00 Shutting down SPTI...
    I 09:13:00 ImgBurn closed!
    ;
    ;
    ; //****************************************\\
    ; ImgBurn Version 2.3.2.0 - Log
    ; Monday, 24 December 2007, 22:19:20
    ; \\****************************************//
    ;
    ;
    I 22:18:41 ImgBurn Version 2.3.2.0 started!
    I 22:18:41 Microsoft Windows XP Media Center Edition (5.1, Build 2600 : Service Pack 2)
    I 22:18:41 Total Physical Memory: 981,484 KB - Available: 547,384 KB
    W 22:18:41 Drive D:\ (FAT32) does not support single files > 4 GB in size.
    W 22:18:41 Drive N:\ (FAT32) does not support single files > 4 GB in size.
    I 22:18:41 Initialising SPTI...
    I 22:18:41 Searching for SCSI / ATAPI devices...
    I 22:18:41 Found 2 DVD±RW/RAMs!
    I 22:19:19 Close Request Acknowledged
    ;
    ;
    ; //****************************************\\
    ; ImgBurn Version 2.3.2.0 - Log
    ; Monday, 24 December 2007, 22:03:00
    ; \\****************************************//
    ;
    ;
    I 22:00:49 ImgBurn Version 2.3.2.0 started!
    I 22:00:49 Microsoft Windows XP Media Center Edition (5.1, Build 2600 : Service Pack 2)
    I 22:00:49 Total Physical Memory: 981,484 KB - Available: 557,512 KB
    W 22:00:49 Drive D:\ (FAT32) does not support single files > 4 GB in size.
    W 22:00:49 Drive N:\ (FAT32) does not support single files > 4 GB in size.
    I 22:00:49 Initialising SPTI...
    I 22:00:49 Searching for SCSI / ATAPI devices...
    I 22:01:34 Found 1 DVD-RAM/+R and 1 DVD±RW/RAM!
    I 22:03:00 Close Request Acknowledged
    I 22:03:00 Closing Down...
    I 22:03:00 Shutting down SPTI...
    I 22:03:00 ImgBurn closed!
    ;
    ;
    ; //****************************************\\
    ; ImgBurn Version 2.3.2.0 - Log
    ; Monday, 24 December 2007, 10:52:16
    ; \\****************************************//
    ;
    ;
    I 04:47:22 ImgBurn Version 2.3.2.0 started!
    I 04:47:22 Microsoft Windows XP Media Center Edition (5.1, Build 2600 : Service Pack 2)
    I 04:47:22 Total Physical Memory: 981,484 KB - Available: 569,680 KB
    W 04:47:22 Drive D:\ (FAT32) does not support single files > 4 GB in size.
    W 04:47:22 Drive N:\ (FAT32) does not support single files > 4 GB in size.
    I 04:47:23 Initialising SPTI...
    I 04:47:23 Searching for SCSI / ATAPI devices...
    I 04:47:23 Found 2 DVD±RW/RAMs!
    I 10:52:16 Close Request Acknowledged
    I 10:52:16 Closing Down...
    I 10:52:16 Shutting down SPTI...
    I 10:52:16 ImgBurn closed!
    Whats next?

    First off, check to see if there is an update to your burner firmware. Secondly, even with the error pop up, allow 30 seconds or more and then click on "Retry" to see if it'll commence with with the burn. It'll also help if you provide a copy of the log. To do so,
    Open ImgBurn=>Click Help and then select ImgBurn logs=>Open the Txt Doc. The newest record should be the first one.

     
  5. ChrisC586

    ChrisC586 Regular member

    Joined:
    Oct 10, 2005
    Messages:
    964
    Likes Received:
    0
    Trophy Points:
    26
    Change over from fat 32 to NTSC filing system on your hard drive.To convert a volume to NTFS from the command prompt
    1.
    Open Command Prompt. Click Start, point to All Programs, point to Accessories, and then click Command Prompt.

    2.
    In the command prompt window, type: convert drive_letter: /fs:ntfs Chris
     
    Last edited: Dec 26, 2007
  6. Cappy66

    Cappy66 Member

    Joined:
    Dec 20, 2007
    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    11
    ---C drive is NTFS. It's the one I use for burning.Whats the next step.
     
  7. pryme_H

    pryme_H Regular member

    Joined:
    Mar 13, 2006
    Messages:
    1,715
    Likes Received:
    0
    Trophy Points:
    46
    Cappy66,
    Do you get the same result when burning a SL disc?
     
  8. Cappy66

    Cappy66 Member

    Joined:
    Dec 20, 2007
    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    11
    No. No problem burning single layer discs.
     
  9. LOCOENG

    LOCOENG Moderator Staff Member

    Joined:
    Feb 4, 2005
    Messages:
    11,493
    Likes Received:
    2
    Trophy Points:
    118
    Destination Device: [5:0:0] LITE-ON DVDRW SHM-165H6S HP10

    Try firmware version HSOE from here ~ http://codeguys.rpc1.org/firmwares.html#SHM-165H6S

    No need to change your file system on other drives if using the .MDS as it tells the burning program how to burn the image. Choose this file when burning DL discs as it also contains the layer break information.

    Power Calibration errors are usually due to one of three things...

    1. Cheap media, you are using a disc with RICOHJPN dye which can be iffy. I would suggest nothing but Verbatim for DL media.
    2. Your burner isn't getting the power needed to execute the command, check your cables to see that they are seated properly from back of burner and PSU. In the worst cases your burner is dying and it's time for a new one.
    3. Your PSU is bad, time for a new one.
     
  10. Rotary

    Rotary Senior member

    Joined:
    Apr 10, 2003
    Messages:
    8,353
    Likes Received:
    0
    Trophy Points:
    116
    whats bugging me here is why the NTSC drive mentioned that is being used doesnt show in the log file???

    perhaps it doesnt? never noticed before...
     
    Last edited: Dec 29, 2007
  11. ChrisC586

    ChrisC586 Regular member

    Joined:
    Oct 10, 2005
    Messages:
    964
    Likes Received:
    0
    Trophy Points:
    26
    Thats why I posted to change file system thinking his N&D drive were extra hard drives. Chris
     
  12. Rotary

    Rotary Senior member

    Joined:
    Apr 10, 2003
    Messages:
    8,353
    Likes Received:
    0
    Trophy Points:
    116
    hmmm. would deffo try some verbs DL though
     

Share This Page