Info regarding sound or other queries within (NO CODE REQUESTS/code POSTING)

Should you need information regarding codes sound or other queries just click on this link and all the information should be there and if not let us know and we will post it when we have it to hand

http://forums.afterdawn.com/thread_view.cfm/531363


This link will bring you back to all our other posts on the previous thread Complete Guide to Starview Installation

http://forums.afterdawn.com/thread_view.cfm/201/517485

 

JTAG GUIDE

Build the JTAG as below.

JTAG is in the corner of the PCB and is a 20pin connector (no pins, just pads) layed out in a 2 x 10 array.

Pin1 is the square pin.

Connections are as follows:

PIN9 = TMS
PIN11 = TCK
PIN13 = TDI
PIN15 = TDO
PIN19 = TRST

Ground is all even number pins.

VCC is the end of capacitor C40 nearest the processor.

The box must be powered up to be flashed (don't worry about the lack of display or picture)

Flashing with JKEYS
-------------------

Run JKEYS and Detect. Should come up as:

Device ID: 0x1D405041
Device: STi5518MVB-X

Choose the IRD model as 4900

Flash would be 29LV160
Start : 7FE00000
Bytes 20000

Go into flash programmer.

Erase chip first by clicking on Erase in the top right

Flash chip with a working TSOP image by clicking on the top-right Program button.


Flashing with S*YMax UP (Easier!)
--------------------------------

If you are having problems flashing with JKEYS you can also use S*YUP. This is much easier to use.

Click on 2mb (0x7FE00000)
Click Start
Click Erase
Click Write

Choose your flash image .. sit back and wait

Thanks to

SunRise



Jtag Tut

http://www.mediafire.com/?7tzcc4dj3yd


SkyMax 2

http://www.mediafire.com/?8fzumnj1k9g

Jkeys

http://www.mediafire.com/?3z9z322ck2x

260 Jtag Flash Image

http://www.mediafire.com/?49jgvte4o0z

 

Yes all links have been kept in tact also on the bottom of my post there is a link to another thread with all codes and other stuff from our original site and also the stuff martin put up on page 4 is there as well have a look you can add the link to yours if you like

 

Fergus can I not access our last home as I had a lot of templates here regarding cable types, jtag problems, and general SV problems, they were posts I made and I just had a note of the page numbers versus the query I had answered.

I had built up a big template set hate to see it gone.

 

Yes you can still link it up or what you can do is put it on the link on my post and put all the stuff you want on it before it gets closed

 

hahah creaky just closed mainanm starview banter thread.

 

ah well it was worth a go.

 

Another new house Thanks for the invite Fergus mate.

 

Right thats it now I am gettin really confused what thread is what. We are going to have to open a thread to find that out. I cannot go through our last home page tonight to take out all my old info, as it will just take too long.

Hopefully it will still be there tomorrow.

 

yea me too , ferg whats the crack with all the info posted before ?

 

pm u creeky ! hope thats ok .....

 

I have posted everything to this link from the other thread so any vital information should be posted there before the link is closed

http://forums.afterdawn.com/thread_view.cfm/531363#3215782

 

glad i found our new home cause i'd have a strview box sitting doing nothing if i did'nt i need all this information to save my life

now i flashed my sv with v4.0 do i need to do anything if the codes change or willit do it all its self thanks

 

Assuming all stays as it is anto, the codes should autoroll.

 

No Anto should do its own job now if you have it running now you can check it autorolls by changing the first 2 numbers in the 00 code exit back out to the screen (picture) it will start updating it should bring your picture back up want to check it and tell me if your's works

 

ferg that worked thanks very much goodnight now i'll leave you in peace

 

I see we have moved and thanks for the invite lol
I must say that the other thread was a biggie and glad we havent moved too far cos Im tired tonight