Power calliberation error ???? please help

Discussion in 'DVD / Blu-ray drives' started by jordan333, Dec 24, 2006.

Thread Status:
Not open for further replies.
  1. jordan333

    jordan333 Guest

    evertime i burn a dvd it come`s up :

    power caliberation error,

    i have tried to fix it buy upgrading the firmware and i have even swapped it with a new dvd drive but its still a no go,
    i have tried nero and dvd decrypter and both will no burn ??

    i am using sony and verbatin media
     
  2. binkie7

    binkie7 Moderator Staff Member

    Joined:
    Feb 12, 2005
    Messages:
    17,588
    Likes Received:
    0
    Trophy Points:
    116
    Hi jordan333
    Since you tried another drive and still the same try a different power connector.

    Here's a blurb from Nero on what causes power calibration errors(applies to dvd's too):
    Power Calibration is controlled by the recorder.

    Before any write operation, all recorders must do a 15 step power test to determine the optimum power for writing to the CD; this is called "Optimum Power Calibration"(OPC). During the write, it continues to do this test to get the best write throughout the whole CD; this is called "Running Optimum Power Calibration" (ROPC).
    This whole process is controlled by the recorder, though initiated by programs such as Nero. There is an area on the inner part of the CD for the test and test data info to be stored. You can use this area up to 999 times.

    If you receive the "Power calibration error" or "Power calibration area is (amost) full" error message, the cause will be either poor media, poor power, or a defective recorder.

    Please try the following solutions:

    * Update the firmware of your recorder. Please check the manufacturer's website for the latest version.
    * Try another brand of CD-R or CD-RW media.
    * Try different power connectors, and for recorders, do not share power with other devices. It needs its own power connector. If the error occurs with an external recorder, the power source in the chassis could be the cause. As a test, try to take the recorder out of the external chassis and connect it internal.
    * Try different configurations, such as taking the CD-ROM to the primary IDE bus as slave and have only the recorder connected to the secondary IDE bus as master.
    * Send the recorder in for service.
     
  3. creaky

    creaky Moderator Staff Member

    Joined:
    Jan 14, 2005
    Messages:
    27,900
    Likes Received:
    1
    Trophy Points:
    96
    hey jordan333, Merry Christmas (again).

    ..in addition to binkie's post..

    ..if it's Nero 6, let's have LAST section of your Nero log which lives in c:\program files\ahead\nero\nerohistory.log but DO NOT post your serial number which usually begins with '1A21' or similar.

    ..if it's Nero 7, let's have LAST section of your Nero log which lives in C:\Program Files\Nero\Nero 7\Core\NeroHistory but DO NOT post your serial number which usually begins with '5C80' or similar.

    Either way you can differentiate sections via this section divider "====== *** Nero-Burning Rom, History File *** ======"
     
  4. binkie7

    binkie7 Moderator Staff Member

    Joined:
    Feb 12, 2005
    Messages:
    17,588
    Likes Received:
    0
    Trophy Points:
    116
    lol - looks like jordan333 will have to figure this out on their own since they are no longer with us :0)


    Merry Xmas!
     
  5. creaky

    creaky Moderator Staff Member

    Joined:
    Jan 14, 2005
    Messages:
    27,900
    Likes Received:
    1
    Trophy Points:
    96
Thread Status:
Not open for further replies.

Share This Page