When opening a disk on dvdshrink it is taking about 2-3 minutes. In the guide it says "This will make less than 30 seconds in most of the cases if you have relatively modern hardware in use" also when converting it to ISO (or MDS in my case as im using FAT32) it is taking around 1hour 15mins. in the guides pic it is only taking 42minutes. and has an encoding Rate of 3.1mb/s when mine averages at about 1.5mb/s I have a P4 3Ghz and 1GB RAM... i see these being 'relatively modern' so does any1 know why it is running so slow or had this problem themselves? Cheers, Matt
Is the DVDs coming out right? If so i wouldnt worry about it. It really depends on the size of the disc. Some do it in 30seconds if its a true DVD5 others take 2 to 5 minutes if its a DVD-9 Loaded. Same with compressing the DVD. Some take 40 minutes some take up to 1 to 1 1/2 hours.
If it takes long. Just dont open any other software. It usually takes me about 1h30m to burn a complete movie. I have the same configurations as your PC
Same here, some movies take WAY longer. Most the time it takes 30 minutes to finish one dvd. I am doing some Disney movies right now and it says 3 hours for two of them. I dont know why it takes soooo much longer.
I ran into yout guys problems and this is how you fix it... Do a system defrag 1st...Then check to see if it help speed up the burning...If not do a system reformat...A full system reformate, so save your files if u need any....At 1st i was reading and writing at 40 mins....then it went to 2 hrs for both...that sucked...I defraged and it help a little....But after then reformat i now read and write at 30 mins.....wow....
what do u mean by deep analysis ? tnx for help.... and i am trying to burn some movies and i always get this error msgs."burn process failed 6x (8,310KB/s)"1A20-0220-0130-1466-3897-3701* Windows XP 5.1 IA32 WinAspi: - ahead WinASPI: File 'C:\Program Files\Ahead\Nero\Wnaspi32.dll': Ver=2.0.1.59, size=160016 bytes, created 11/11/2003 5:49:52 AM Nero API version: 6.3.0.0 Using interface version: 6.3.1.4 Installed in: C:\Program Files\Ahead\Nero\ Application: ahead\Nero - Burning Rom Recorder: < VOM-12E48X> Version: 100A - HA 1 TA 1 - 6.3.0.0 Adapter driver: <atapi> HA 1 Drive buffer : 2048kB Bus Type : via Inquiry data (1) -> ATAPI, detected: ATAPI Connected to MMC as unknown drive with class-nr : 1 Drive is autodetected - recorder class: Std. MMC recorder === Scsi-Device-Map === DiskPeripheral : SAMSUNG SV0602H atapi Port 0 ID 0 DMA: On CdRomPeripheral : VOM-12E48X atapi Port 1 ID 1 DMA: Off === CDRom-Device-Map === VOM-12E48X E: CDRom0 ======================= AutoRun : 1 Excluded drive IDs: CmdQueuing : 1 CmdNotification: 2 WriteBufferSize: 36700160 (0) Byte ShowDrvBufStat : 0 EraseSpeed : 0 BUFE : 0 Physical memory : 223MB (228844kB) Free physical memory: 88MB (90932kB) Memory in use : 60 % Uncached PFiles: 0x0 Use Static Write Speed Table: 0 Use Inquiry : 1 Global Bus Type: default (0) Check supported media : Disabled (0) 29.1.2005 NeroAPI 8:26:58 PM #1 Phase 112 File APIProgress.cpp, Line 250 DVD-Video files reallocation started 8:26:59 PM #2 Phase 114 File APIProgress.cpp, Line 250 DVD-Video files reallocation completed (no file modified) 8:26:59 PM #3 Phase 111 File APIProgress.cpp, Line 250 DVD-Video files sorted 8:27:01 PM #4 Text 0 File Reader.cpp, Line 118 Reader running 8:27:01 PM #5 Text 0 File Writer.cpp, Line 124 Writer VOM-12E48X running 8:27:01 PM #6 ISO9660GEN -11 File geniso.cpp, Line 3882 First writeable address = 0 (0x00000000) 8:27:01 PM #7 ISO9660GEN -11 File geniso.cpp, Line 3882 First writeable address = 0 (0x00000000) 8:27:01 PM #8 Text 0 File Burncd.cpp, Line 3094 Turn on Disc-At-Once, using DVD media 8:27:32 PM #9 Text 0 File DlgWaitCD.cpp, Line 239 Last possible write address on media: 2298495 (510:46.45) Last address to be written: 2297999 (510:39.74) 8:27:32 PM #10 Text 0 File DlgWaitCD.cpp, Line 244 Write in overburning mode: FALSE 8:27:32 PM #11 Text 0 File DlgWaitCD.cpp, Line 2068 Recorder: VOM-12E48X, Media type: DVD-R Disc Manufacturer: MXL RG - 02 Disc Application Code: 64, Disc Physical Code: 193 8:27:32 PM #12 Text 0 File DlgWaitCD.cpp, Line 405 >>> Protocol of DlgWaitCD activities: <<< ========================================= Insert empty disc to write to. (Medium in drive: unknown. Medium required by compilation: DVD+R/RW, DVD-R/RW.) 8:27:32 PM #13 Text 0 File ThreadedTransferInterface.cpp, Line 779 Setup items (after recorder preparation) 0: TRM_DATA_MODE1 (CTransferItem) 2 indices, index0 (150) not provided original disc pos #0 + 2298000 (2298000) = #2298000/510:40.0 relocatable, disc pos for caching/writing not required/required, no patch infos -> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2298000 blocks [ VOM-12E48X ] -------------------------------------------------------------- 8:27:32 PM #14 Text 0 File ThreadedTransferInterface.cpp, Line 948 Prepare recorder [ VOM-12E48X ] for write in CUE-sheet-DAO DAO infos: ========== MCN: "" TOCType: 0x00; Session Closed, disc fixated Tracks 1 to 1: 1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4706304000, ISRC "" DAO layout: =========== __Start_|____Track_|_Idx_|_RecDep_|_CtrlAdr_ 0 | lead-in | 0 | 0x00 | 0x41 0 | 1 | 0 | 0x00 | 0x41 0 | 1 | 1 | 0x00 | 0x41 2298000 | lead-out | 1 | 0x00 | 0x41 8:27:32 PM #15 Phase 24 File APIProgress.cpp, Line 250 Caching of files started 8:27:32 PM #16 Text 0 File Burncd.cpp, Line 4061 Cache writing successful. 8:27:32 PM #17 Phase 25 File APIProgress.cpp, Line 250 Caching of files completed 8:27:32 PM #18 Phase 36 File APIProgress.cpp, Line 250 Burn process started at 6x (8,310 KB/s) 8:27:32 PM #19 Text 0 File ThreadedTransferInterface.cpp, Line 2264 Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0 8:27:32 PM #20 Text 0 File DVDR.cpp, Line 1424 Recording mode: Sequential Recording Mode 8:27:32 PM #21 Text 0 File Mmc.cpp, Line 19397 Set BUFE: supported -> ON 8:27:32 PM #22 Text 0 File DVDR.cpp, Line 1539 Start write address at LBA 0 DVD high compatibility mode: Yes 8:27:32 PM #23 Text 0 File Cdrdrv.cpp, Line 7912 ---- DVD Structure: Physical Format Information (00h) ---- Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050 Book Type: DVD-R (2), Part Version: 5 Disc Size: 120 mm, Maximum Rate: <not specified> (F h) Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable Linear Density: 0,267 um/bit, Track Density: 0,74 um/track Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW) End Physical Sector Number of Data Area: 0 h End Sector Number in Layer 0: 0 h Data in Burst Cutting Area (BCA) does not exist Media Specific: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 8:27:39 PM #24 Text 0 File Cdrdrv.cpp, Line 1276 20:27:39.625 - VOM-12E48X\H1 T1 : Queue again later 8:38:54 PM #25 SCSI -1135 File Cdrdrv.cpp, Line 1430 SCSI Exec, HA 1, TA 1, LUN 0, buffer 0x00B90000 Status: 0x04 (0x01, SCSI_ERR) HA-Status 0x00 (0x00, OK) TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND) Sense Key: 0x03 (KEY_MEDIUM_ERROR) Sense Code: 0x0C Sense Qual: 0x00 CDB Data: 0x2A 0x00 0x00 0x00 0xFE 0xA0 0x00 0x00 0x20 0x00 0x00 0x00 Sense Data: 0x71 0x00 0x03 0x00 0x00 0x00 0x00 0x0A 0x00 0x00 0x00 0x00 0x0C 0x00 8:38:54 PM #26 CDR -1135 File Writer.cpp, Line 301 Write error 8:38:54 PM #27 Text 0 File ThreadedTransfer.cpp, Line 229 all writers idle, stopping conversion 8:38:54 PM #28 Text 0 File ThreadedTransfer.cpp, Line 223 conversion idle, stopping reader 8:38:54 PM #29 Text 0 File DVDR.cpp, Line 1743 EndDAO: Last written address was 65183 8:43:10 PM #30 Phase 38 File APIProgress.cpp, Line 250 Burn process failed at 6x (8,310 KB/s) Existing drivers: File 'WNASPINT.DLL': Ver=V1.20, size=57344 bytes, created 2/3/2003 4:24:08 PM File 'Drivers\PXHELP20.SYS': Ver=2.02.40a, size=16416 bytes, created 10/21/2002 9:02:00 AM (Prassi/Veritas driver for win 2K) Registry Keys: HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option) WHY DO I ALWAYS GET THIS ERROR ?
To do a system reformat...You must use the disk that came with the pc....Meaning the windows disk....Put it into your drive and restart pc......If u get the black screen like i do all the time their will be lots of letters on it....wait for it to say boot off disk if it does click enter....Or it might do it by itself
DVD Shrink is extremely slow. I would recomend not using it if at all possible. I use DVD X Copy to backup all my movie. It takes about 45min. to an hour to compress and burn a movie. Haven't had any problems with it yet.
If your certain all your hardware is in good working condition then make sure you don't have any spyware, thats a real killer in the time department most of the time.
keizsa, please edit out your nero serial # in your burn error report. Starts out as 1A20-xxxx-xxxx-xxxx-xxxx-xxxx You are using maxell -4x yellowtops-mxlrg-02. [WHY DO I ALWAYS GET THIS ERROR ?] Burn process started at 6x (8,310 KB/s) Sounds like you may have to reduce your backup target and burn speed in dvd shrink. Reduce that backup target: Open up dvd shrink edit preferences If it's set dvd-5/scroll till it's on custom Enter 4360 mbs Click ok. Also keep that burn speed at 4x on this media.It's very good media,but not ty quality. [CdRomPeripheral : VOM-12E48X atapi Port 1 ID 1 DMA: Off] You might want to go to device manager to check this drive,I believe it should be dma-if available. If it says pio,the uninstall,and reboot. Dvd and dvd shrink,main movie only= 20 mins to 40 mins on my pc. I have done entire dvd-5's- under 18 minutes-total process time.Initial analyzing takes about 1 minute,unless it is a dvd-9. They take about 2 mins.
