"TheB0x" & "Starview Clone" No Power...

Alright guys, ive currently got "The B0x" reciver & Starview Clone, Both boxes currently have no power, and they both have PINS ...insted of pads.

So ive Jtaged "The B0x" i get this ..


Init JTAG
IDCODE : 1D405041
CPU : STi5518
Stop CPU
Clear Trap : Please Wait...
Load Trap -> Ram : Please Wait...
Load Trap : LEN Ok
Init Trap : Please Wait...
Trap_Wptr 80000534
Trap_Iptr 80000140
Start Trap : Please Wait...
Load EMI : Please Wait...
Init OK
---------------------
Init JTAG
DCU OK
Trap_Wptr : 80000534
Erase ADR[7FE00000] : Please Wait...
Erase success !!!
---------------------
Init JTAG
DCU OK
Trap_Wptr : 80000534
File : C:\Documents and Settings\Alex\My Documents\Starview&EuroVox&Dbox\Jtag DEAD starview\tsop flash bin.bin
Write Flash ADR[7FE00000] LEN[00200000] : Please Wait...
Write Flash END
---------------------

Still with no power on "The B0x" any ideas guys ?

And on the clone box normal starview.. the jtag doesnt work on the pinss any help guys ?

Cheers

 

any onee ... pleasee

 

..... Please help me ..

 

any one ?? im confused now

 

Any oneee ??? ... ive searched with no luck.

 

Solo, sc0user or fergus might be on later & might be able to help you out, they are the jtag specialists.

 

cheers 4 reply mate. hope they can help.

 

Any one ? Thanks

 

Bump would be nice to have sum tv on for xmas ... lol

 

any help guyss .. has any one hadf this problem b4 ?

 

any one?

 

pleaseee can any 1 help me e...

 

Hi Solo, as Noel said last week lol... you will have to wait till Sc0user see this as he is the man on jtagging, did you send him a PM?

 

No mate my laptop is playing up , i need him too see this a.s.a.p, ive tried everything, it Jtaged Ok aswell.. just no powerr still hope he can help.

 

Hello

 

Hey sc0user, could you tell me whats up lol ? .. ive been looking about for information but no luck.. like i said ive jtaged "TheBox" fine still no power, the StarView with Pins wont even Jtag .. im confused ><

 

Hey sc0user, any chance you could help me, Ive looked about for information, but had no luck ! Like i said i Jtaged "TheBox" fine but no power, and the Starview wont jtag at all .. or do i need a diff jtag ? .. Thanks

 

Yes it looks like it has erased and wrote to the TSOP. So you are correct to that point. There is also power but have you checked all the voltages from the PSU to the main board?

Remember the TSOP file you are using is actually the SV1 TSOP. I havent had much success with jtagging an SV2 mainly because I havent taken the TSOP from an SV2.

Regards the clone lets leave that for a bit as thats the easier of the two.

 

Thanks for the reply!

So where would i find the TSOP file for SV2?, Also i havnt checked the mainbord to psu as i dnt no what im looking for. ,


And as for the clone no idea what that is either lol..

 

I dont have the box any more, (donated it for a good cause). You should be able to read the TSOP from a working SV2 with Jkeys.

The voltage from the PSU can be checked with a multimeter. You should see 3.3V, 7V, 12V & 23V. If you see a drop at the 3.3V line it is usually caused by a faulty cap.