Viewsat 2000 key down again???

Hello I have the Viewsat 2000 receiver and the key went out just a couple of minutes ago.

I need the key for Dish
*NOTE: VIEWSAT IS DIFFERENT FROM THE OTHER RECEIVERS:
an example of key:

00--leave alone
08: D9 E3 98 5A CC 2D AC 6E
09: D2 46 8D 0F FC D1 2B 8F
88: FA E1 97 4D E7 31 02 F8
98: B7 9A 92 5C 39 C7 3B 4D

so yeah, i really need help my t.v show is starting soon! =/

 

The keys are posted under new keys

 

yes but mines has 4 row unlike the one u posted please look at the example i gave

 

There are 16 keys per line in the ones that I posted. Take the first 8 and place them in row one and the next 8 in row 2 and so on.

 

Ohhh! i understand everything now, sorry it is my first time that keys went down and im new. thank you very much for your help

 

Not a problem. There is a new bin that will make auto roll work again

 

is this the bin work for view sat 2000 xtreme, coz i lost the ppv and hbh channels 3 days ago

thanks

 

Click this link and download the newest bin. Right there on hte front page.

http://d3.b8.344a.static.theplanet.com/index.php

 

thank you man for the link, but i have problem, when i download the file and unzip it, it does not want to open the file with format PGM, so there is any way to just get them with out all this headach.

thank u again dude

 

Don't open the program file. All you do is load the file as it is after you unzip it to your usb stick and use it that way.


A. Loading your BIN using Null cable:

? Connect serial cable (NULL) to PC>STB
? Open up Loader of choice (PVR-Loader 1.1 or Loader2)
? Click on Tool>Configuration>Com port (Default is com 1)
? Click on Open File
? Click on PC>STB (Notice the progression bar in loader)
? Turn the power in the back ON
? Wait for Loader say Completed. Then on box LCD front panel screen say I.N.S.T>END>0000 or until clock count to 0.001
IT IS VERRY IMPORTANT. DO NOT TURN THE POWER OFF TO SOON
? Turn the power OFF in front and power OFF in back
? After downloading the “BIN”, unhook NULL cable from PC>STB
? Connect all the cables to your box/TV
? Turn the power ON in the front and back
? Press Menu key
? Select Installation and press OK
? Select Antenna Setup and press OK
? Select your Sat.
? Here if you have a DISEqC switch enter the port #, Motor or Legacy SW
? No LNB Type need to select (from new, you have only two selection Standard and Universal). STB will select your LNB Automatic
? Press Exit and select Yes for saving the settings
? Your back to Antenna Setup screen
? Here you have Three choices:
1. Channel Scan
2. Auto Scan
3. Blind Scan
? Select Auto Scan
? Press OK
? You are in the Auto Scan window and you see the Bird(Sat.) you selected and on the top of your screen are three options:
1. Search option
2. Network search
3. Scan Start
? You don’t change nothing here, go down and select Scan Start and press OK
? You do this for all the Birds (Sat.) you have
? Wait for Autoroll and watch TV


B. Loading your BIN using USB Jump Drive

? Connect all the cables to your box/TV
? Turn the power ON from the front and back switch
? Press Menu key
? Select Installation and press OK
? Select Antenna Setup and press OK
? Select your Sat.
? Here if you have a DISEqC switch enter the port #, Motor or Legacy SW
? No LNB Type need to select (from new, you have only two selection Standard and Universal). STB will select your LNB Automatic
? Press Exit and select Yes for saving the settings
? Your back to Antenna Setup screen
? Here you have Three choices:
1. Channel Scan
2. Auto Scan
3. Blind Scan
? Select Auto Scan
? Press OK
? You are in the Auto Scan window and you see the Bird(Sat.) you selected and on the top of your screen are three options:
1. Search option
2. Network search
3. Scan Start
? You don’t change nothing, go down and select Scan Start and press OK
? You do this for all the Birds (Sat.) you have
? Now its time to download your BIN ( Newest bins here http://forums.f2atv.com/showthread.php?t=103801
? Insert the Memory Stick in your PC and transfer the bin in. Than insert in your STB and in the Main Menu select System information and press OK
? Select Receiver Upgrade and press OK
? Go down to the bottom of the window, select USB and press OK
? A new window opens with some Korean files, years, etc.
? In the bottom of the window, it is your bin selects and presses OK
VERY IMPORTANT. DO NOT TURN THE POWER OFF
? After you load the bin, the STB will reboot automatic
? Wait for Autoroll and watch TV

 

thank you so much man, i donot have the cable right now but i will buy one and learn how to do it by my self.

 

You can load them with a usb memory stick. Much easier that way, don't have to hook up a computer to the ultra.

 

yes but i do not have the USB plug in my view sat xtreme 2000.

thanks

 

My bad, I thought you had a ultra

 

This might help. Use only the extreme instructions. All the dish settings are there also.


If this is a new STB/receiver you should get at least two files before you start.
LOADER2.ZIP (viewsat utility section )
An up to date latest file, found in the Viewsat Files (fixs and updates) section here

Use only Platinum PGM files on Platinum or Lite
Extreme PGM files are for Extreme only

HOW TO FLASH.
You can flash (load) your receiver with a bin on top of the bin (file) you already have. It will replace it.
Use a Nul CABLE RS232 on your receiver from the computer. Or use a Nul adaptor from Radio Shack number 26-264B to make a straight through cable a Nul cable. Take the cable off going to the LNB to be safe. If you don't have a 9 pin plug on your computer you may need to use a USB to Serial cable 26-183 at Radio Shack.

Un-zip all the files and hook up the cable from your computer to the STB, keep the STB off with the switch in the back. Start the loader-2 and click on OPEN FILES. Find the bin file you un-zipped that now ends in PGM. Click on it and it will automatically go on the first line of the loader. Click on the icon just below the word TOOL and check the COM PORT. Then turn STB on from the back and at first light click PC->STB on the loader. If the progress bar don't move after about a minute start over again. Sometimes the timing is critical. Even try turning STB on from the back first then click PC->STB. Don't do anything as the progress bar is going across. Make sure the Computer & STB are done before you go to the next step. They may not get done at the same time.

When file transfer is completed, the Front Panel will display:
"inst" for 15 seconds while the software is being installed
"DONE" for 10 seconds while the ViewSat does housekeeping chores
Next, the ViewSat automatically REBOOTs
" on " will be displayed and when the reboot is complete, "0000"
You may NOW turn "OFF" the ViewSat and connect it to your TV and satellite dish cable


Some problems occur from users not waiting long enough after flashing. The unit now has an extra step involved. When finished it will say END, then 0000, then boot, then END, then back to last channel or 0000. You must wait till this process finishes before unplugging. Unplugging while it is finishing causes the unit to fail



PLUGGING IN CABLE.
Make sure you plug in the cable from the dish to the receiver at the LNB 13/18v INPUT. Not the ANT IN. The cables coming from the dish to the switch should be put on the switch at the same number as you have set in your receiver. "Example", 119 cable goes on number 1 on the diseqc switch and the receiver has #1 for 119 in the program. You can only get one Satellite for each one LNB you have. Two LNB's two Satellites, and so on.

Now you will need to set your settings. Below is what most have.
MENU, INSTALLATION, then 0000 or 0937 or 2668 or 3570 then ANTENNA SETUP then side arrow to ECHOSTAR 7 119.0W check your Satellite setting. Then do the same to ECHOSTAR 8,10 110.0W

EchoStar 7 - 119. ECHO 7
LNB Power------ON
LNB Type-------Standard For dish pro set to OCS
LNB Freq-----------11250
22kHz-------------Off unless you have a 22kHz switch turn on.
TP Freq----------12339
Search option-----All
DiSEqC 1.0------Port 1
Motor--------------Off
Legacy SW------None

HIGHLIGHT any line EXCEPT Top "SATELLITE 119.0W" line
F1 to REGULAR scan the 110 TP's
When finished,

"EXIT" and "YES" to Save.
Go to next Sat to scan

EchoStar 8,10 - 110.0W May also say Echostar 6,8
LNB Power------ON
LNB Type-------Standard For Dish pro set to OCS
LNB Freq-----------11250
22kHz-------------Off unless you have a 22kHz switch turn on
TP Freq----------12224
Search option-----All
DiSEqC 1.0------Port 2
Motor--------------Off
Legacy SW------None

HIGHLIGHT any line EXCEPT Top "SATELLITE 110.0W" line
F1 to REGULAR scan the 110 TP's
When finished,

"EXIT" and "YES" to Save.


Satellite: Nimiq 1,3 91.0W
LNB Power------ON
LNB Type-------Standard For dish Pro set to OCS
LNB Freq-----------11250
22kHz-------------OFF you can't use a 22kHz switch with more then two Satellites.
TP Freq----------12224
Search option-----All
DiSEqC 1.0------Port 3
Motor--------------Off
Legacy SW------None

HIGHLIGHT any line EXCEPT Top "SATELLITE 91.0W" line
F1 to REGULAR scan the 91 TP's


"EXIT" and "YES" to Save

THIS IS WHAT MY SETTINGS ARE. You can start here then change them later.
MENU, OPTIONS
Close Caption---------OFF
Sort by SID-------------ON
AUTO TP---------------ON
AUTO ROLL-----------ON
EPG Hours-------------24
Full Channel Name—ON

Now exit out to Channel and wait for keys to roll may take up to 15 minutes leave on 1 channel

Installation, Parental Control
Receiver lock Off
Menu Lock ON
Information timeout 3
Maturity Rate Unblocked
Change PIN Code ????

MENU, SYSTEM SETTINGS
System Settings----Letter Box
Screen Type--------------63
Menu Language-------English
Audio Language------English
Channel Mode---------Normal

HOW TO DO A FACTORY DEFAULT
MENU, INSTALLATION
When you do this you will also clean out your channels.

How To Enter Keys Manually In Your Xtream.
1. Menu
2.Installation
3.Enter Pin 0000
4.Code
5.Nagra
6.Left until you see what ever Satellite you want.
Put 00 keys on line 08 & 09 don't change the 08 or 09 number
Put 01 keys on line 88 & 89 don't change the 88 or 89 number
EXIT once then OK to save, the light color is the one you pick to save then EXIT out.

HOW TO SEARCH/EDIT, ANTENNA CONFIGURATION, ADD SATELLITE, RENAME SATELLITE, DELETE SATELLITE.
MENU, INSTALLATION, 0000, SIDE ARROW TO DN OR BEV, then down once to NETWORK SEARCH ON, Then down once to HAMMER ICON then side arrow to what you want to do.
ADD A TP
To add a TP go to the channel scan section, select Dish or Nimiq 1,3, go down to the green screw driver and hammer icon, hit ok to enter the tp list, then F1 button to add new TP You can also hit the pause button in this section to get a overview of other actions.

HOW TO TURN AUTO-ROLL OFF & ON
MENU,OPTIONS then go to AUTO-ROLL

SET GMC TIME
MENU, INSTALLATION, TIME SETTING. Set to - 5:00 for east coast

RESET RECEIVER
Sometimes you need to do a reset, (hard boot). Turn power off then on from the back.
Edit/Delete Message

 

thank u so much dude, u are so smart.

 

hi bro i need ur help i connect the cable and i open the file and when i click pc to stb the messeg pop up and say status: error initializing

i do not know what to do dude, i follow all the steps u give me

thanks

 

What com port are you using?

 

i am useing com port 1, but when i connect my usb to computer and the computer pick up com port. and said this one is avillable

 

Do you have the usb drivers installed?