AfterDawn Forums

OPENBOX X5 CCCAM SETTING

This discussion thread has 15 messages.

#1
Hi lads i just bought openbox x5. I am having problem with the cccam client setup. I have done everything but it say scrambled channels even when it shows online. Can anyone help me pls.
▼▼ This topic has 14 answers - they are below this advertisement ▼▼
AfterDawn Advertisement
#2
hi
i had the same problem when using the remote control to input the line
but then i loaded it using a usb stick and it worked straight away
hope this helps
#3
do you know how to connect by diseqc? thanks for the help.
#4
no sorry mate
#5
Hi can you tell me how to activate my ccam with usb im having the same problem
#6
i had the same problem
so i made a cccam.cfg file on notepad on my computer
saved the cline on there
put it on a usb
then uploaded it via usb under the cccam section menu
rebooted and started working
#7
Originally posted by sekondi:
Hi lads i just bought openbox x5. I am having problem with the cccam client setup. I have done everything but it say scrambled channels even when it shows online. Can anyone help me pls.


Hey mate... Did u ever find an answer to ur issue? I have just bought the x5 and I am having the same issue
#8
i there, i have just bought the openbox x5, and im having problems putting my line in, i dont know how to put them in through usb, can anyone help please in how to do this as ive only ever put them in by remote beforehand, thank you
#9
copy the line detail and put it into a txt doc, past it and call the doc CCAM.CFG, load to a USB, go to the box menu and load the cline, if any digit is wrong it wont work,
Menu -> Network Local Settings and select CCcam Plug Setting and click the OK button
Now select CCcam,cfg [CCcam Plug] and click the OK button, you should then see a check mark or tick appear,indicating you have selected the file, if there is no tick shown, then you have not selected anything, and nothing will be installed. Click yellow button and it should read the file,
Now highlight each cline you wish to activate, by clicking the OK button a tick will appear next to each cline you have activated.

hm-9001s Chan Editor - https://hotfile.com/dl/184330990/a6b825a/PolarEditOctagon10x8Setup_0.725.zip.html
Ariva 250 Patched Firmware -
Ariva 250 Chan Editor - http://www.ferguson-digital.eu/en/downl...mbo/Editor.zip/
Ariva 150 Patched -
#10
I got a similar problem just that i can watch a channel for about 30 seconds and then a message comes up saying Scrambled Channel and the screen turns black, if i switch to any different channels it still does the same thing.
#11
Originally posted by MICKAH:
copy the line detail and put it into a txt doc, past it and call the doc CCAM.CFG, load to a USB, go to the box menu and load the cline, if any digit is wrong it wont work,
Menu -> Network Local Settings and select CCcam Plug Setting and click the OK button
Now select CCcam,cfg [CCcam Plug] and click the OK button, you should then see a check mark or tick appear,indicating you have selected the file, if there is no tick shown, then you have not selected anything, and nothing will be installed. Click yellow button and it should read the file,
Now highlight each cline you wish to activate, by clicking the OK button a tick will appear next to each cline you have activated.
my openbox x5 give me scrambled channel. followed the pakcu video on youtube still does not work. the youtube, vod and astro radio channel works. Any suggestion? update to latest firware? current is 27mar13. Appreciate your help.
#12
There is 2 ways to input the line, through usb or through remote control

"on computer open notepad copy n paste the line details and save as cccam.cfg,onto usb"
insert usb into box

for usb setup:

press menu
system set up
press ok on Access control
press ok on CCcam client setup
press ok on update files by usb
CCcam.cfg is already highlighted in red, press red button to load
screen message will confirm load success or load fail
press exit to go back a page if load was successful
press ok on CCcam.cfg edit
enter code 0000
press ok on CCcam edit
you should now see the line you just added press ok and a tick at the end will appear
under active to confirm selected
press blue button (message connects to server please wait)
Status will now be On-line

To setup by remote

press menu
system set up
press ok on Access control
press ok on CCcam client setup
press ok on CCcam.cfg edit
enter code 0000
press ok on CCcam edit
press the red button to edit next line with "empty" in it
Single server setup page will appear
Active server: ignore
IP(DNS): enter address from line eg what.ever.com
Port: enter first set of numbers from line eg 05151
ID: enter next set of numbers & letters from line
Password: enter last set of numbers & letters from line
Protocol: use right arrow to change from Newcamd to CCcam
press exit button
you should now see the line you just added press ok and a tick at the end will appear
under active to confirm selected
press blue button (message connects to server please wait)
Status will now be On-line
you should now see the line you just added press ok and a tick at the end will appear
under active to confirm selected
press blue button (message connects to server please wait)
Status will now be On-line

you are now all set up, you get scrambled channels it because
on this box it needs satellite setup page setup correctly these settings vary
depending on your location im in process of testing different setting, ive tried lnb frequency and transponder numbers from dreambox and openbox S11 but some channels works and some dont
Im in Birmingham UK and have tried satellite:
19.2E Astra 1
23.5E Astra 3A
28.2E Freesat-Astra 2
33.0E Eurobird 3

but I need to know the correct frequency and transponder numbers
for these satellites and which is the best satellite to use
#13
Originally posted by smilapee:
There is 2 ways to input the line, through usb or through remote control

"on computer open notepad copy n paste the line details and save as cccam.cfg,onto usb"
insert usb into box

for usb setup:

press menu
system set up
press ok on Access control
press ok on CCcam client setup
press ok on update files by usb
CCcam.cfg is already highlighted in red, press red button to load
screen message will confirm load success or load fail
press exit to go back a page if load was successful
press ok on CCcam.cfg edit
enter code 0000
press ok on CCcam edit
you should now see the line you just added press ok and a tick at the end will appear
under active to confirm selected
press blue button (message connects to server please wait)
Status will now be On-line

To setup by remote

press menu
system set up
press ok on Access control
press ok on CCcam client setup
press ok on CCcam.cfg edit
enter code 0000
press ok on CCcam edit
press the red button to edit next line with "empty" in it
Single server setup page will appear
Active server: ignore
IP(DNS): enter address from line eg what.ever.com
Port: enter first set of numbers from line eg 05151
ID: enter next set of numbers & letters from line
Password: enter last set of numbers & letters from line
Protocol: use right arrow to change from Newcamd to CCcam
press exit button
you should now see the line you just added press ok and a tick at the end will appear
under active to confirm selected
press blue button (message connects to server please wait)
Status will now be On-line
you should now see the line you just added press ok and a tick at the end will appear
under active to confirm selected
press blue button (message connects to server please wait)
Status will now be On-line

you are now all set up, you get scrambled channels it because
on this box it needs satellite setup page setup correctly these settings vary
depending on your location im in process of testing different setting, ive tried lnb frequency and transponder numbers from dreambox and openbox S11 but some channels works and some dont
Im in Birmingham UK and have tried satellite:
19.2E Astra 1
23.5E Astra 3A
28.2E Freesat-Astra 2
33.0E Eurobird 3

but I need to know the correct frequency and transponder numbers
for these satellites and which is the best satellite to use
hi,
thanks for the guide..
for..."on computer open notepad copy n paste the line details and save as cccam.cfg,onto usb"

which line are you referring to please? what line?
thanks
#14
Hi can get n line to work need help.
#15
[img][/img]

mostyhad
This discussion thread has been automatically closed, as it hasn't received any new posts during the last 180 days. This means that you can't post replies or new questions to this discussion thread.

If you have something to add to this topic, use this page to post your question or comments to a new discussion thread.