Starview receiver problem

go to starview then documentation and then k22 i think its called.

 

opened that it looks very difficult can any one do tis 4 me ......

 

Send a pm to Fergusrb as he is in the process of doing them. He is based in Kildare.

 

scouse i need that software .....

 

Are you going to try it yourself?

 

dose any1 kno if the software put on the clones will do the same as the originals and in turn kill them to

 

OK here is all the info you need follow this along with the guide i have pointed you to.

Build the JTAG as below.

JTAG is in the corner of the PCB and is a 20pin connector (no pins, just pads) layed out in a 2 x 10 array.

Pin1 is the square pin.

Connections are as follows:

PIN9 = TMS
PIN11 = TCK
PIN13 = TDI
PIN15 = TDO
PIN19 = TRST

Ground is all even number pins.

VCC is the end of capacitor C40 nearest the processor.

The box must be powered up to be flashed (don't worry about the lack of display or picture)

Flashing with JKEYS
-------------------

Run JKEYS and Detect. Should come up as:

Device ID: 0x1D405041
Device: STi5518MVB-X

Choose the IRD model as 4900

Flash would be 29LV160
Start : 7FE00000
Bytes 20000

Go into flash programmer.

Erase chip first by clicking on Erase in the top right

Flash chip with a working TSOP image by clicking on the top-right Program button.


Flashing with S*YMax UP (Easier!)
--------------------------------

If you are having problems flashing with JKEYS you can also use S*YUP. This is much easier to use.

Click on 2mb (0x7FE00000)
Click Start
Click Erase
Click Write

Choose your flash image .. sit back and wait

Thanks to

SunRise



Jtag Tut

http://www.mediafire.com/?7tzcc4dj3yd


SkyMax 2

http://www.mediafire.com/?8fzumnj1k9g

Jkeys

http://www.mediafire.com/?3z9z322ck2x

260 Jtag Flash Image

http://www.mediafire.com/?49jgvte4o0z

 

No the fixed 2.57 is 100% safe for clones, 2.60 upwards will kill clones.

 

Hi guys, i am a complete novice at this and would appreciate some help please. I recently bought the starview 2 digital reciever and connected it to the NTL cable i have. The menu screen etc appears, i then selected NTL as my provider, ran the auto scan but it doesnt pick any channels up, just comes up with the message "FAILURE". Is this supposed to happen for first time users or am i supposed to be doing anything beforehand. Please please help me, really appreciate it. Thanks.

 

do you have the n** cable in the cable input on the back of your box.

 

Hi there, yeh its in the cable input at the back of the box.

 

double check please.also are you in ireland or uk.

 

I am in the UK, ive just checked, and its definitely in, just tested my connection using the old analogue box and the cable seems fine. Done the scan on the starview box and still coming up with constant failures.

 

try scanning on tele**** and c&w because i have heard of people on n** that when they scanned got noting but when scanned on tele**** got all the channels.

 

Just tried that, and still no luck, the connection i have is the cable going into the box, then another cable going from the cable to the tv aerial port (not sure what this cable is called) and thats all. Am i doing anything wrong? Really appreciate the advice your giving me anyway.

 

go to main menu go to system information and what is the api

 

ryan it sounds like the emu isnt on !

 

How do i switch the EMU on? cheers

 

that why i asked api

 

go to main menu press 1570 and its at the bottom of the menu.but if your on 2.58api you won't be able to access the menu.