1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

CloneDVD2 Takes Over 2 Hours To Rip

Discussion in 'Copy DVD to DVDR' started by glen68, May 3, 2005.

  1. glen68

    glen68 Member

    Joined:
    Feb 27, 2004
    Messages:
    2
    Likes Received:
    0
    Trophy Points:
    11
    here is the problem, While using CloneDVD2 2.7.5.3 It takes 2 - 3 Hours just to create the dvd files, & about 45 mins to burn. I can use DVD Decrepter to rip in about 28 Mins speeds as high as 4.1x


    DVD Decrepter took as long as clone oringinally until I played with DMA settings, but that did not fix clone's problem


    I know the drive is fine as I have been swaping it in out with my other computer there it takes on 22 mins to create the dvd files & 8 mins to burn


    The Specs are

    Liteon Drive 451S latest firmware

    1 Gig Of Ram

    Windows 2000 Service Pack 4

    Drivers For The Ide Controllers are

    Microsoft
    6/19/2003
    5.0.2195.6717

    With all the latest windows updates


    The Dvd Burner is on The Primary IDE Channel & it is On Device 1

    Transfer Mode is DMA if availble
    Current Transfer Mode is DMA Mode



    I have tried swapping cables & postion on the mother board for the disc drive
     
  2. squizzle

    squizzle Active member

    Joined:
    Apr 19, 2004
    Messages:
    2,271
    Likes Received:
    0
    Trophy Points:
    66
    Since Decrypter can rip in good time but Clone can't, sounds like a software issue. I'm not too familiar with CloneDVD, but check over the settings and options there. There might be something a little off there.

    [edit] Do you have AnyDVD installed too?
     
    Last edited: May 4, 2005
  3. bilbo65

    bilbo65 Regular member

    Joined:
    Feb 24, 2005
    Messages:
    2,102
    Likes Received:
    0
    Trophy Points:
    46
    Perhaps you need to update your copy of CloneDVD2. There is a later version.
     
  4. hursty

    hursty Active member

    Joined:
    Nov 22, 2004
    Messages:
    4,549
    Likes Received:
    1
    Trophy Points:
    66
    i have clonedvd2 version 2.7.3.1,and have never had a problem like this,
    i would try uninstalling it and do a full install again,
    also check whether your aspi layers are functioning properly,
    you have no spy/adware,
    do a defrag
     
  5. permatex

    permatex Regular member

    Joined:
    May 4, 2003
    Messages:
    229
    Likes Received:
    0
    Trophy Points:
    26
    clone dvd2 has been updated to 2.8.2.1.
     
  6. permatex

    permatex Regular member

    Joined:
    May 4, 2003
    Messages:
    229
    Likes Received:
    0
    Trophy Points:
    26
    clone dvd2 has been updated to 2.8.2.1.
     
  7. Mik3h

    Mik3h Regular member

    Joined:
    Oct 18, 2004
    Messages:
    2,833
    Likes Received:
    0
    Trophy Points:
    46
    Ah, I had the same problem, go with Hursty's advice, you should check for spyware/adware, check for viruses, make sure you got decent HDD space, then defrag. It worked for me, although I switched to DVD Shrink after I did all of the above.

    -Mike.
     
    Last edited: May 18, 2005
  8. permatex

    permatex Regular member

    Joined:
    May 4, 2003
    Messages:
    229
    Likes Received:
    0
    Trophy Points:
    26
    i am running clond dvd2 trial version,i have burned 13 dvds with no problem,24 to 28 min to decode and 19 to 28 min to burn.im using a p-4 4.40 ghz,2 gigs ram,80 gig hard drive 7200rpm and hp dvd+r 8x media.generally under one hour per dvd,i consider this time reasonable for a fairly good dvd.right now i have four programs im using to copy dvds,trying to come up with better copy progran than what im used to using.
     
  9. Mik3h

    Mik3h Regular member

    Joined:
    Oct 18, 2004
    Messages:
    2,833
    Likes Received:
    0
    Trophy Points:
    46
    I can't understand why you need 4 programs to backup DVDs..

    All you need is,

    : DVD Decrypter.

    and

    : DVD Shrink.

    Life's Necessities..

    -Mike
     
  10. permatex

    permatex Regular member

    Joined:
    May 4, 2003
    Messages:
    229
    Likes Received:
    0
    Trophy Points:
    26
    tried decripter and shrink,still like dvdxcopy.im trying sonething else.
     
  11. bilbo65

    bilbo65 Regular member

    Joined:
    Feb 24, 2005
    Messages:
    2,102
    Likes Received:
    0
    Trophy Points:
    46
    I have a similar view as Mik3h, but my choices are AnyDVD and CloneDVD 2.
     
    Last edited: May 18, 2005

Share This Page