1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

DMA-driver error, CRC error - While burning

Discussion in 'Nero discussion' started by glazberg, Nov 24, 2007.

Page 2 of 2
  1. 56delray

    56delray Regular member

    Joined:
    Feb 8, 2007
    Messages:
    629
    Likes Received:
    0
    Trophy Points:
    26
    I agree you could have some have a hardware problem, but when that is fixed, media will be an issue.
    I could not find any 16x Teac
    However if you look at the link, you can see they use 6 or more sources for the DVDs listed.
    Some very good (Taiyo Yuden), some good (Ritek, Prodisc), some poor (CMC) and some I have never heard of.

    So when you buy Teac, you are getting potluck.
    If you shop around and watch for sales, you can get better media at a good price with few or no coasters.

    http://www.videohelp.com/dvdmedia?d...rder=Name&hits=50&search=Search+or+List+Media
     
    56delray, Nov 27, 2007
    #21
  2. glazberg

    glazberg Member

    Joined:
    Nov 24, 2007
    Messages:
    9
    Likes Received:
    0
    Trophy Points:
    11
    Ok, so here's my next report:
    I've replaced the IDE cable with a new one. the old one does seem to be messed up.

    I've disconnected the DVD-ROM drive and left the DVD-R (jumpered as master). Burning works fine.

    BUT - when I re-connect the DVD-ROM (jumpered as slave, using the middle connector in the IDE) I get the same error again.
    What's the deal?
    I don't have another IDE port in my MotherBoard (I have 2 ports. both are used - one for 2 HardDisks and the second is supposed to be used for the 2 DVD drives.

    Here's the log of the failed burning process:

    Windows XP 5.1
    IA32
    WinAspi: -

    NT-SPTI used
    Nero Version: 7.10.1.0
    Internal Version: 7, 10, 1, 0

    Recorder: <Optiarc DVD RW AD-7170A> Version: 1.04 - HA 1 TA 3 - 7.10.1.0
    Adapter driver: <IDE> HA 1
    Drive buffer : 2048kB
    Bus Type : default (0) -> ATAPI, detected: ?
    CD-ROM: <HL-DT-ST DVD-ROM GDR8162B>Version: 0015 - HA 1 TA 1 - 7.10.1.0
    Adapter driver: <IDE> HA 1

    === Scsi-Device-Map ===
    DiskPeripheral : WDC WD400BB-00DEA0 atapi Port 0 ID 0 DMA: On
    DiskPeripheral : Maxtor 6Y080P0 atapi Port 0 ID 1 DMA: On
    CdRomPeripheral : Optiarc DVD RW AD-7170A atapi Port 1 ID 0 DMA: On
    CdRomPeripheral : HL-DT-ST DVD-ROM GDR8162B atapi Port 1 ID 1 DMA: On

    === CDRom-Device-Map ===
    Optiarc DVD RW AD-7170A E: CdRom3
    HL-DT-ST DVD-ROM GDR8162B F: CdRom1
    =======================

    AutoRun : 1
    Excluded drive IDs:
    WriteBufferSize: 83886080 (0) Byte
    BUFE : 0
    Physical memory : 1023MB (1048048kB)
    Free physical memory: 700MB (717040kB)
    Memory in use : 31 %
    Uncached PFiles: 0x0
    Use Inquiry : 1
    Global Bus Type: default (0)
    Check supported media : Disabled (0)

    1.12.2007
    ISO compilation
    23:13:14 #1 Text 0 File SCSIPTICommands.cpp, Line 424
    LockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL

    23:13:15 #2 Text 0 File Isodoc.cpp, Line 6666
    Iso document burn settings
    ------------------------------------------
    Determine maximum speed : FALSE
    Simulate : FALSE
    Write : TRUE
    Finalize CD : TRUE
    Multisession : FALSE
    Burning mode : DAO
    Mode : 1
    ISO Level : 1 (Max. of 11 = 8 + 3 char)
    Character set : ISO 9660
    Joliet : TRUE
    Allow pathdepth more than 8 directories : TRUE
    Allow more than 255 characters in path : TRUE
    Write ISO9660 ;1 file extensions : TRUE

    23:13:15 #3 ISO9660GEN -11 File Geniso.cpp, Line 3343
    First writeable address = 0 (0x00000000)

    23:13:15 #4 Text 0 File Burncd.cpp, Line 3508
    Turn on Disc-At-Once, using DVD media

    23:13:15 #5 Text 0 File DlgWaitCD.cpp, Line 307
    Last possible write address on media: 2295103 (510:01.28, 4482MB)
    Last address to be written: 2215775 (492:23.50, 4327MB)

    23:13:15 #6 Text 0 File DlgWaitCD.cpp, Line 319
    Write in overburning mode: NO (enabled: CD)

    23:13:15 #7 Text 0 File DlgWaitCD.cpp, Line 2972
    Recorder: Optiarc DVD RW AD-7170A, Media type: DVD+R
    Disc Manufacturer ID: CMC MAG, Media Type ID: M01, Product revision number: 0
    Disc Application Code: 0, Extended Information Indicators: 7

    23:13:15 #8 Text 0 File DlgWaitCD.cpp, Line 493
    >>> Protocol of DlgWaitCD activities: <<<
    =========================================

    23:13:15 #9 Text 0 File ThreadedTransferInterface.cpp, Line 793
    Setup items (after recorder preparation)
    0: TRM_DATA_MODE1 ()
    2 indices, index0 (150) not provided
    original disc pos #0 + 2215776 (2215776) = #2215776/492:23.51
    relocatable, disc pos for caching/writing not required/ required
    -> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2215776 blocks [E: Optiarc DVD RW AD-7170A]
    --------------------------------------------------------------

    23:13:15 #10 Text 0 File ThreadedTransferInterface.cpp, Line 995
    Prepare [E: Optiarc DVD RW AD-7170A] for write in CUE-sheet-DAO
    DAO infos:
    ==========
    MCN: ""
    TOCType: 0x00; Session Closed, disc fixated
    Tracks 1 to 1: Idx 0 Idx 1 Next Trk
    1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4537909248, ISRC ""
    DAO layout:
    ===========
    ___Start_|____Track_|_Idx_|_CtrlAdr_|_____Size_|______NWA_|_RecDep__________
    0 | lead-in | 0 | 0x41 | 0 | 0 | 0x00
    0 | 1 | 0 | 0x41 | 0 | 0 | 0x00
    0 | 1 | 1 | 0x41 | 2215776 | 0 | 0x00
    2215776 | lead-out | 1 | 0x41 | 0 | 0 | 0x00

    23:13:15 #11 Text 0 File SCSIPTICommands.cpp, Line 215
    SPTILockVolume - completed successfully for FSCTL_LOCK_VOLUME

    23:13:15 #12 Text 0 File Burncd.cpp, Line 4294
    Caching options: cache CDRom or Network-Yes, small files-No (<64KB)

    23:13:15 #13 Phase 24 File dlgbrnst.cpp, Line 1762
    Caching of files started

    23:13:15 #14 Text 0 File Burncd.cpp, Line 4413
    Cache writing successful.

    23:13:15 #15 Phase 25 File dlgbrnst.cpp, Line 1762
    Caching of files completed

    23:13:15 #16 Phase 36 File dlgbrnst.cpp, Line 1762
    Burn process started at 16x (22,160 KB/s)

    23:13:15 #17 Text 0 File ThreadedTransferInterface.cpp, Line 2721
    Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

    23:13:15 #18 Text 0 File Cdrdrv.cpp, Line 9872
    ---- Disc Structure: Physical Format Information (00h) ----
    Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
    Book Type: DVD+R (10), Part Version: 1.0x (1)
    Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
    Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
    Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
    Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
    End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
    Data in Burst Cutting Area (BCA) does not exist
    Disc Application Code: 0 / 0 h
    Extended Information indicators: 7 h
    Disc Manufacturer ID: CMC.MAG.
    Media type ID: M01
    Product revision number: 0
    Number of Physical format information bytes in use in ADIP up to byte 63: 56
    Media Specific [16..63]:
    00 00 07 43 4D 43 20 4D - 41 47 00 4D 30 31 00 38 ...CMC.MAG.M01.8
    23 54 37 18 00 3E 6E 00 - 70 62 15 15 0B 0B 08 08 #T7..>n.pb......
    01 19 1B 0B 0B 0E 0F 01 - 00 00 00 00 00 00 00 00 ................

    23:13:15 #19 SPTI -1065 File SCSIPassThrough.cpp, Line 179
    CdRom3: SCSIStatus(x02) WinError(0) NeroError(-1065)
    Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
    Sense Code: 0x20
    Sense Qual: 0x00
    CDB Data: 0xF9 15 01 FF 00 00 00 00 00 00 00 00
    Sense Area: 0x70 00 05 00 00 00 00 0A 00 00 00 00 20

    23:13:15 #20 SPTI -1065 File SCSIPassThrough.cpp, Line 179
    CdRom3: SCSIStatus(x02) WinError(0) NeroError(-1065)
    Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
    Sense Code: 0x20
    Sense Qual: 0x00
    CDB Data: 0xF9 14 01 FF 00 00 00 00 00 00 00 00
    Sense Area: 0x70 00 05 00 00 00 00 0A 00 00 00 00 20

    23:13:15 #21 Text 0 File DVDR.cpp, Line 7402
    Drive: Optiarc DVD RW AD-7170A
    Book Type request [gen]: DVD-ROM, write to EEPROM
    Changing the Book Type was finished with error, return code -1065

    23:13:15 #22 Text 0 File DVDR.cpp, Line 6783
    Drive: Optiarc DVD RW AD-7170A
    Book Type request [NEC]: DVD-ROM
    Changing the Book Type was finished with error, return code -1065

    23:13:15 #23 Text 0 File DVDPlusRW.cpp, Line 675
    Start write address at LBA 0
    DVD high compatibility mode: Yes

    23:13:15 #24 Text 0 File ThreadedTransfer.cpp, Line 269
    Pipe memory size 83836800

    23:13:39 #25 SPTI -1502 File SCSIPassThrough.cpp, Line 179
    CdRom3: SCSIStatus(x02) WinError(0) NeroError(-1502)
    Sense Key: 0x04 (KEY_HARDWARE_ERROR)
    Sense Code: 0x08
    Sense Qual: 0x03
    CDB Data: 0x2A 00 00 00 00 00 00 00 20 00 00 00
    Sense Area: 0x70 00 04 00 00 00 00 0A 00 00 00 00 08 03
    Buffer x092b0040: Len x10000
    0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
    0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
    0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

    23:13:39 #26 CDR -1502 File Writer.cpp, Line 303
    DMA-driver error, CRC error
    E: Optiarc DVD RW AD-7170A

    23:13:55 #27 Phase 127 File dlgbrnst.cpp, Line 1762
    Generating DVD high compatibility borders

    23:14:39 #28 Text 0 File DVDPlusRW.cpp, Line 935
    EndDAO: Last written address 0

    23:14:39 #29 CDR -1093 File WriterStatus.cpp, Line 162
    No seek complete
    E: Optiarc DVD RW AD-7170A

    23:14:44 #30 TRANSFER -24 File WriterStatus.cpp, Line 162
    Could not perform end of Disc-at-once

    23:14:45 #31 Phase 38 File dlgbrnst.cpp, Line 1762
    Burn process failed at 16x (22,160 KB/s)

    23:14:48 #32 Text 0 File SCSIPTICommands.cpp, Line 261
    SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME

    23:14:52 #33 Text 0 File Cdrdrv.cpp, Line 11185
    DriveLocker: UnLockVolume completed

    23:14:52 #34 Text 0 File SCSIPTICommands.cpp, Line 424
    UnLockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL


    Existing drivers:

    Registry Keys:
    HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)

     
    glazberg, Dec 1, 2007
    #22
  3. creaky

    creaky Moderator Staff Member

    Joined:
    Jan 14, 2005
    Messages:
    27,900
    Likes Received:
    1
    Trophy Points:
    96
    It's handy that this thread popped into my inbox, i've just been sent (by mistake) many 100s of CMC MAG M01 instead of the awesome RICHOJPNR03 i always buy (both look the same externally, they're Maxell 16x +R); the only reason i found out that i'd been sent subpar discs was when a couple of burns failed using the Maxell's (this never happens and i use 1000s of the Maxell RICOHJPNR03's). Checked the failed discs and was extremely annoyed to find out i'd been sent CMC MAG M01 by mistake. Luckily the supplier will take them back and send me what i asked for, and it's always possible that the supplier's not at fault, they could have been sent these useless discs by mistake.

    Grrrrr.....
     
    Last edited: Dec 1, 2007
    creaky, Dec 1, 2007
    #23
  4. gwendolin

    gwendolin Senior member

    Joined:
    Jun 29, 2005
    Messages:
    7,447
    Likes Received:
    0
    Trophy Points:
    116
    @creaky

    In my reply on 26th I also stated that CMC mags were poor quality discs and advised to slow burn to 4X but I see that advice was given in vain...poster still using same discs and burning at 16X, as did Laddyboy on the 27th.
     
    gwendolin, Dec 1, 2007
    #24
  5. creaky

    creaky Moderator Staff Member

    Joined:
    Jan 14, 2005
    Messages:
    27,900
    Likes Received:
    1
    Trophy Points:
    96
    i very rarely comment on media these days, but these discs left me no choice; i though maybe it could be a firmware issue on my burners but i found a fair few threads over at cdfreaks and i was most surprised to find a lot of people over there calling these discs some bad names; there are apparently CMC discs that are highly thought of over there, i think they're CMC MAG E01 or AM3 (or both) but i didn't find much good stuff written about the M01's, i'm stuck with 800 of the things until the supplier takes them away to go into landfill
     
    creaky, Dec 1, 2007
    #25
  6. binkie7

    binkie7 Moderator Staff Member

    Joined:
    Feb 12, 2005
    Messages:
    17,588
    Likes Received:
    0
    Trophy Points:
    116
    For this error the cause is usually hardware related - could be wrong - but yeah I'd definitely use different media.

    Try this - kind of a pain but will help pin down the problem.
    Switch the drives - dvd-rom to master, burner to slave - switch the jumper pins too. Now try and burn - use simulation instead of doing a straight burn.
    Fails then just take out the dvd-rom and try again w/ the burner connected as slave. I'd do a simulation burn also.
    Burn either a cd or dvd - you've been getting the same error for both.
     
    binkie7, Dec 1, 2007
    #26
  7. glazberg

    glazberg Member

    Joined:
    Nov 24, 2007
    Messages:
    9
    Likes Received:
    0
    Trophy Points:
    11
    @gwendolin

    I haven't had the chance to buy different media yet. About the burning speed - I forgot about it, but should it really matter? If the burner works fine at X16 when it's the only thing connected to the IDE cable, shouldn't it work fine at the same speed even if something else is connected to the same cable?
     
    glazberg, Dec 2, 2007
    #27
  8. gwendolin

    gwendolin Senior member

    Joined:
    Jun 29, 2005
    Messages:
    7,447
    Likes Received:
    0
    Trophy Points:
    116
    Although the discs you are using say they are 16X I wouldnt advise burning at MAX speed of 16X....they are, as stated , poor quality and are prone to failing even at 4X.
    I always recommend burning at 4X even with my Verbatims, after all how much time do you actually save, Cheers.
     
    gwendolin, Dec 2, 2007
    #28
  9. creaky

    creaky Moderator Staff Member

    Joined:
    Jan 14, 2005
    Messages:
    27,900
    Likes Received:
    1
    Trophy Points:
    96
    @glazberg - this thread is going around in circles; by all means try 4x, until you start trying the suggestions you will still be stuck in this thread instead of watching successfully burned movies; i even dropped by to add my own personal experience on these discs, ie i was suddenly having burning problems; changed the discs back to the ones i've been using (1000s of) for years and all is well again.

    you need to try 4x next and update us on your progress...
     
    creaky, Dec 2, 2007
    #29
  10. wdlndboy

    wdlndboy Member

    Joined:
    Jan 2, 2008
    Messages:
    1
    Likes Received:
    0
    Trophy Points:
    11
    Ok guys I guess I am having the same problem. Well the other day I bought this computer off some guy I didn't even know. Yah I know stupid right well it turns out that it has all these problems like Javascript not working I have tried everything believe me everything and then when I go to use the DVD burner/Cd Burner this message pops up DMA-driver error, CRC error go this is frustrating I don't know too much about computers and I have read this whole thread plus tons more and still it makes no sense. I have tried changing my write speed but I have been unsuccessful in doing so. I can't seem to find how. Here is the log from Nero. Please someone help me!

    Windows User
    None
    4C85-2006-3005-4001-0556-76E0-0900-4026-X8E5-**** (*)

    Windows XP 5.1
    IA32
    WinAspi: -
    ahead WinASPI: File 'C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll': Ver=2.0.1.74, size=169792 bytes, created 3/20/2007 9:09:56 AM

    NT-SPTI used
    Nero Version: 7.5.13.6
    Internal Version: 7, 5, 13, 6
    (Nero Express)
    Recorder: <SONY DVD RW AW-G170A> Version: 1.62 - HA 1 TA 0 - 7.5.13.6
    Adapter driver: <IDE> HA 1
    Drive buffer : 2048kB
    Bus Type : default (0) -> ATAPI, detected: ?
    CD-ROM: <TOSHIBA DVD-ROM SD-M1202>Version: 1020 - HA 1 TA 1 - 7.5.13.6
    Adapter driver: <IDE> HA 1

    === Scsi-Device-Map ===
    DiskPeripheral : SAMSUNG SV1204H atapi Port 0 ID 0 DMA: On
    CdRomPeripheral : SONY DVD RW AW-G170A atapi Port 1 ID 0 DMA: On
    CdRomPeripheral : TOSHIBA DVD-ROM SD-M1202 atapi Port 1 ID 1 DMA: On

    === CDRom-Device-Map ===
    SONY DVD RW AW-G170A D: CDRom0
    TOSHIBA DVD-ROM SD-M1202 E: CDRom1
    =======================

    AutoRun : 1
    Excluded drive IDs:
    WriteBufferSize: 73400320 (0) Byte
    BUFE : 0
    Physical memory : 503MB (515608kB)
    Free physical memory: 132MB (135184kB)
    Memory in use : 73 %
    Uncached PFiles: 0x0
    Use Inquiry : 1
    Global Bus Type: default (0)
    Check supported media : Disabled (0)

    2.1.2008
    ISO compilation
    12:09:31 AM #1 Text 0 File SCSIPTICommands.cpp, Line 411
    LockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL

    12:09:31 AM #2 Text 0 File Isodoc.cpp, Line 6517
    Iso document burn settings
    ------------------------------------------
    Determine maximum speed : FALSE
    Simulate : FALSE
    Write : TRUE
    Finalize CD : FALSE
    Multisession : TRUE
    Multisession type: : Start multisession
    Burning mode : DAO
    Mode : 1
    ISO Level : 1 (Max. of 11 = 8 + 3 char)
    Character set : ISO 9660
    Joliet : TRUE
    Allow pathdepth more than 8 directories : TRUE
    Allow more than 255 characters in path : TRUE
    Write ISO9660 ;1 file extensions : TRUE

    12:09:32 AM #3 ISO9660GEN -11 File Geniso.cpp, Line 3332
    First writeable address = 0 (0x00000000)

    12:09:32 AM #4 Text 0 File Burncd.cpp, Line 3471
    Turn on Disc-At-Once, using DVD media

    12:09:33 AM #5 Text 0 File DlgWaitCD.cpp, Line 306
    Last possible write address on media: 2295103 (510:01.28, 4482MB)
    Last address to be written: 11359 ( 2:31.34, 22MB)

    12:09:33 AM #6 Text 0 File DlgWaitCD.cpp, Line 318
    Write in overburning mode: NO (enabled: CD)

    12:09:33 AM #7 Text 0 File DlgWaitCD.cpp, Line 2929
    Recorder: SONY DVD RW AW-G170A, Media type: DVD+R
    Disc Manufacturer ID: CMC MAG, Media Type ID: E01, Product revision number: 0
    Disc Application Code: 0, Extended Information Indicators: 3

    12:09:33 AM #8 Text 0 File DlgWaitCD.cpp, Line 490
    >>> Protocol of DlgWaitCD activities: <<<
    =========================================

    12:09:33 AM #9 Text 0 File ThreadedTransferInterface.cpp, Line 792
    Setup items (after recorder preparation)
    0: TRM_DATA_MODE1 ()
    2 indices, index0 (150) not provided
    original disc pos #0 + 11360 (11360) = #11360/2:31.35
    relocatable, disc pos for caching/writing not required/ required
    -> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 11360 blocks [D: SONY DVD RW AW-G170A]
    --------------------------------------------------------------

    12:09:55 AM #10 Text 0 File ThreadedTransferInterface.cpp, Line 995
    Prepare [D: SONY DVD RW AW-G170A] for write in CUE-sheet-DAO
    DAO infos:
    ==========
    MCN: ""
    TOCType: 0x00; Session Closed, disc fixated
    Tracks 1 to 1: Idx 0 Idx 1 Next Trk
    1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 23265280, ISRC ""
    DAO layout:
    ===========
    ___Start_|____Track_|_Idx_|_CtrlAdr_|_____Size_|______NWA_|_RecDep__________
    0 | lead-in | 0 | 0x41 | 0 | 0 | 0x00
    0 | 1 | 0 | 0x41 | 11360 | 0 | 0x00
    0 | 1 | 1 | 0x41 | 11360 | 0 | 0x00
    11360 | lead-out | 1 | 0x41 | 0 | 0 | 0x00

    12:09:55 AM #11 Text 0 File SCSIPTICommands.cpp, Line 209
    SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME

    12:09:55 AM #12 Phase 24 File dlgbrnst.cpp, Line 1760
    Caching of files started

    12:09:56 AM #13 Text 0 File Burncd.cpp, Line 4355
    Cache writing successful.

    12:09:56 AM #14 Phase 25 File dlgbrnst.cpp, Line 1760
    Caching of files completed

    12:09:56 AM #15 Phase 36 File dlgbrnst.cpp, Line 1760
    Burn process started at 8x (11,080 KB/s)

    12:09:56 AM #16 Text 0 File ThreadedTransferInterface.cpp, Line 2712
    Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

    12:09:56 AM #17 Text 0 File Cdrdrv.cpp, Line 9261
    ---- DVD Structure: Physical Format Information (00h) ----
    Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
    Book Type: DVD+R (10), Part Version: 1.0x (1)
    Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
    Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
    Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
    Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
    End Physical Sector Number of Data Area: 26053F h
    End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
    Data in Burst Cutting Area (BCA) does not exist
    Disc Application Code: 0 / 0 h
    Extended Information indicators: 3 h
    Disc Manufacturer ID: CMC.MAG.
    Media type ID: E01
    Product revision number: 0
    Number of Physical format information bytes in use in ADIP up to byte 63: 56
    Media Specific [16..63]:
    00 00 03 43 4D 43 20 4D - 41 47 00 45 30 31 00 38 ...CMC.MAG.E01.8
    23 54 37 10 02 38 6A 02 - 88 67 15 15 0B 0B 08 08 #T7..8j..g......
    01 19 1B 0C 0C 0C 0D 01 - 00 00 00 00 00 00 00 00 ................

    12:09:56 AM #18 Text 0 File DVDPlusRW.cpp, Line 674
    Start write address at LBA 0
    DVD high compatibility mode: Yes

    12:10:24 AM #19 SPTI -1502 File SCSIPassThrough.cpp, Line 179
    CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1502)
    Sense Key: 0x04 (KEY_HARDWARE_ERROR)
    Sense Code: 0x08
    Sense Qual: 0x03
    CDB Data: 0x2A 00 00 00 00 00 00 00 20 00 00 00
    Sense Area: 0x70 00 04 00 00 00 00 0A 00 00 00 00 08 03
    Buffer x22030040: Len x10000
    0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
    0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
    0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

    12:10:24 AM #20 CDR -1502 File Writer.cpp, Line 299
    DMA-driver error, CRC error
    D: SONY DVD RW AW-G170A

    12:10:38 AM #21 Phase 127 File dlgbrnst.cpp, Line 1760
    Generating DVD high compatibility borders

    12:11:25 AM #22 CDR -1093 File WriterStatus.cpp, Line 162
    No seek complete
    D: SONY DVD RW AW-G170A

    12:11:25 AM #23 TRANSFER -24 File WriterStatus.cpp, Line 162
    Could not perform end of Disc-at-once

    12:11:25 AM #24 Phase 38 File dlgbrnst.cpp, Line 1760
    Burn process failed at 8x (11,080 KB/s)

    12:11:25 AM #25 Text 0 File SCSIPTICommands.cpp, Line 254
    SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME

    12:11:30 AM #26 Text 0 File Cdrdrv.cpp, Line 10538
    DriveLocker: UnLockVolume completed

    12:11:30 AM #27 Text 0 File SCSIPTICommands.cpp, Line 411
    UnLockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL


    Existing drivers:

    Registry Keys:
    HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
     
    wdlndboy, Jan 2, 2008
    #30
  11. binkie7

    binkie7 Moderator Staff Member

    Joined:
    Feb 12, 2005
    Messages:
    17,588
    Likes Received:
    0
    Trophy Points:
    116
    @wdlndboy
    Sounds like you have much more going on then meets the eye.
    You'll need to start a new thread for your problem. Makes things less confusing and forum rules.
    Try the other suggestions in this thread too - different media, check the jumper settings etc.
     
    binkie7, Jan 2, 2008
    #31
  12. cyprusrom

    cyprusrom Active member

    Joined:
    Jan 5, 2006
    Messages:
    5,439
    Likes Received:
    1
    Trophy Points:
    96
    @wdlndboy
    Beside getting good media( which is more than recommended, but I doubt it will fix your problem since is a hardware(burner/cables...) issue, here are some fixes that worked for other people ( I don't know if this is a repeat, didn'ttake the time to read through the first 2 pages of this thread. Next time don't hijack someone else's thread, start your own like binkie said)
    This also translates into "LOGICAL UNIT COMMUNICATION CRC ERROR (ULTRA-DMA/32) (040803), which means the data can't be properly verified between the hard drive and the burner, there is poor communication. If you have a 40-pin cable, you might have to change it for a 80-pin( it might be as simple as that). Also you might have to reconfigure the 2 drives-reader and burner-(master/slave setup).



    http://club.cdfreaks.com/f44/sony-d...ation-crc-error-ultra-dma-32-040803-a-133258/

    @glazberg
    you got a new cable. Is it a 80-pin? You might need that instead of 40-pin
    http://forums.speedlabs.org/index.php?topic=1056.msg12669
     
    cyprusrom, Jan 2, 2008
    #32
  13. glazberg

    glazberg Member

    Joined:
    Nov 24, 2007
    Messages:
    9
    Likes Received:
    0
    Trophy Points:
    11
    I replaced the cable (don't know if it's 40 or 80 pins), and connected only the DVD burner to it. Sicne that worked, and when I tried reconnecting the other DVD drive it didn't work, I figured I don't really need the other DVD drive...

    Yeah, I know that's lame, but at least I can burn....

     
    glazberg, Jan 3, 2008
    #33
Page 2 of 2

Share This Page