dvd decrypter I/O error

Discussion in 'DVDR' started by mscavie24, Mar 8, 2008.

  1. mscavie24

    mscavie24 Member

    Joined:
    Mar 8, 2008
    Messages:
    3
    Likes Received:
    0
    Trophy Points:
    11
    I have never had a problem with DVD decrypter until recently. When I started having problems with DVD decrypter I switched to DVDFab. DVDFab will not work either. I am using the latest version of DVD decrypter, windows xp home edition, a Compaq Presario SR125ONX computer and a double layer 8x DVD +- r/rw. Any help would be appreciated.

    Error message:

    I/O Error!
    Device: [0:0:0] HL-DT-ST DVDRRW GWA-4083B 1309 (E:) (ATA)

    ScsiStatus: 0x02
    Interpretation: Check Condition

    CDB: 28 00 00 01 2f 99 00 00 01 00
    Interpretation: Read (10) - Sector: 77721
    Sense Area: 70 00 03 00 00 00 00 0E 00 00 00 00 10 00 00 00 00 00
    Interpretation: ID CRC or ECC Error

    Abort Retry Ignore
     
    mscavie24, Mar 8, 2008
    #1
  2. Rotary

    Rotary Senior member

    Joined:
    Apr 10, 2003
    Messages:
    7,606
    Likes Received:
    0
    Trophy Points:
    116
    cant read discs

    is this burning or ripping ?
     
    Rotary, Mar 9, 2008
    #2
  3. mscavie24

    mscavie24 Member

    Joined:
    Mar 8, 2008
    Messages:
    3
    Likes Received:
    0
    Trophy Points:
    11
    ripping
     
    mscavie24, Mar 10, 2008
    #3
  4. creaky

    creaky Moderator Staff Member

    Joined:
    Jan 14, 2005
    Messages:
    27,900
    Likes Received:
    1
    Trophy Points:
    96
    creaky, Mar 10, 2008
    #4
  5. Rotary

    Rotary Senior member

    Joined:
    Apr 10, 2003
    Messages:
    7,606
    Likes Received:
    0
    Trophy Points:
    116
    or dirty / scratched disc?
     
    Rotary, Mar 11, 2008
    #5
  6. mscavie24

    mscavie24 Member

    Joined:
    Mar 8, 2008
    Messages:
    3
    Likes Received:
    0
    Trophy Points:
    11
    a few scratches, but not to bad. when i ignore all read errors, the picture of the movie is ok, but the sound is bad.
     
    mscavie24, Mar 12, 2008
    #6
  7. TrebEevob

    TrebEevob Member

    Joined:
    Mar 29, 2008
    Messages:
    1
    Likes Received:
    0
    Trophy Points:
    11
    As a newbie to the DVD scene at large it is not surprising that I should have at least one problem, so here it is.

    I have used my DVD drive to rip, shrink and burn protected DVD's onto backup disks. The process being the usual. I rip with DVDfab or DVD Decrypter, and then shrink through DVDshrink. And usually IMGBurn afterwards. All of these programs are of the latest versions as far as I could find, and I am using disks that are undamamged.

    The problem emerges when when I attempt to rip files from some DVD's and at a certain point, say 30% complete, I get an error that reports that there was an error while reading, and I can abort, retry, or ignore. My only guess is that there is some protection on the disk which cannot be decoded, which does not make sense, because this disk is older than some others that I have completed without incident.

    I have tried two versions of DVDfab, and DVD Decrypter, and the result is the same. So my request is only for some enlightenment as to why I canno rip certain disks, and if there is a way to remedy the problem. Any and all responses will be appreciated! Thanks.
     
    TrebEevob, Mar 29, 2008
    #7
  8. Rotary

    Rotary Senior member

    Joined:
    Apr 10, 2003
    Messages:
    7,606
    Likes Received:
    0
    Trophy Points:
    116
    couple things to note/try

    some apps conflict with eachother only keep on your system what you need

    try the trial of anydvd running in background while ripping with another app like dvd shrink...

    some brand new dvds sealed then you open up clean wont rip as they are bad pressings (return to shop) and get another...
     
    Rotary, Mar 30, 2008
    #8

Share This Page