Eurovox 2007 Red

Jkeys will help you flash the tsop to the box it is similar to SkyMax.

 

Thanks for your help, my box is ok now.

 

Hi scouser you around i could use your help

 

Scouser is offline at the moment

 

Thanks Celt just post your query Jlewis and I will see what I can do.

 

Hi Scouser,

I tried the following:After program never got a yes to to "Program at address 0x7FE00000, size 0x200000? also couldn't see option to choose Tsop. Any ideas


Try this method using the same tsop file.


Connect JTAG and Power up EuroVox

Start JKEYS

Click on "Development Panel"
Click OK to ingore the warning.

** SEE BELOW IF YOU GET AN ERROR HERE **

If all goes well you will get into the development panel.

In the user functions box:

Type in the address: 80000000
Click on "Load to . . ."

Select the file "unlock_28FxxxC3.bin"

Click "Trigger User"

Close the current window.

Click on "Flash Programming"

Choose the model number as: DXD426RD (1 Chip-GLA)


In the section on the right:

Leave the box above set to "Full"

Click "Erase"

Select YES. This will take a minute to erase.

Click on "Program"

Select YES to "Program at address 0x7FE00000, size 0x200000?"

Choose your TSOP file

Sit and wait for OK to become active, then click it.

Close JKEYS and power the box down.

Disconnect your JTAG

Power the box on. If all has gone well then it should boot up ready for you to rescan for your channels.




*** If you get an error trying to get into the devleopment windows ****

Power the box down and run SkyMax v2.2
Power the box up
Press start.

This seems to reset the box when JKEYS cannot connect (DCU errors).

Close SkyMax and start JKEYS and try again.



Personally I went with Skymax first and then jkeys as it seems to work better.



SkyMax 2

http://www.mediafire.com/?8fzumnj1k9g

Jkeys
http://www.mediafire.com/?e9dyyzgn8q3

 

Hi Scouser,

I tried the following:After program never got a yes to to "Program at address 0x7FE00000, size 0x200000? also couldn't see option to choose Tsop. Any ideas


Try this method using the same tsop file.


Connect JTAG and Power up EuroVox

Start JKEYS

Click on "Development Panel"
Click OK to ingore the warning.

** SEE BELOW IF YOU GET AN ERROR HERE **

If all goes well you will get into the development panel.

In the user functions box:

Type in the address: 80000000
Click on "Load to . . ."

Select the file "unlock_28FxxxC3.bin"

Click "Trigger User"

Close the current window.

Click on "Flash Programming"

Choose the model number as: DXD426RD (1 Chip-GLA)


In the section on the right:

Leave the box above set to "Full"

Click "Erase"

Select YES. This will take a minute to erase.

Click on "Program"

Select YES to "Program at address 0x7FE00000, size 0x200000?"

Choose your TSOP file

Sit and wait for OK to become active, then click it.

Close JKEYS and power the box down.

Disconnect your JTAG

Power the box on. If all has gone well then it should boot up ready for you to rescan for your channels.




*** If you get an error trying to get into the devleopment windows ****

Power the box down and run SkyMax v2.2
Power the box up
Press start.

This seems to reset the box when JKEYS cannot connect (DCU errors).

Close SkyMax and start JKEYS and try again.



Personally I went with Skymax first and then jkeys as it seems to work better.



SkyMax 2

http://www.mediafire.com/?8fzumnj1k9g

Jkeys
http://www.mediafire.com/?e9dyyzgn8q3

 

Hi Scouser,

I tried the following:After program never got a yes to to "Program at address 0x7FE00000, size 0x200000? also couldn't see option to choose Tsop. Any ideas


Try this method using the same tsop file.


Connect JTAG and Power up EuroVox

Start JKEYS

Click on "Development Panel"
Click OK to ingore the warning.

** SEE BELOW IF YOU GET AN ERROR HERE **

If all goes well you will get into the development panel.

In the user functions box:

Type in the address: 80000000
Click on "Load to . . ."

Select the file "unlock_28FxxxC3.bin"

Click "Trigger User"

Close the current window.

Click on "Flash Programming"

Choose the model number as: DXD426RD (1 Chip-GLA)


In the section on the right:

Leave the box above set to "Full"

Click "Erase"

Select YES. This will take a minute to erase.

Click on "Program"

Select YES to "Program at address 0x7FE00000, size 0x200000?"

Choose your TSOP file

Sit and wait for OK to become active, then click it.

Close JKEYS and power the box down.

Disconnect your JTAG

Power the box on. If all has gone well then it should boot up ready for you to rescan for your channels.




*** If you get an error trying to get into the devleopment windows ****

Power the box down and run SkyMax v2.2
Power the box up
Press start.

This seems to reset the box when JKEYS cannot connect (DCU errors).

Close SkyMax and start JKEYS and try again.



Personally I went with Skymax first and then jkeys as it seems to work better.



SkyMax 2

http://www.mediafire.com/?8fzumnj1k9g

Jkeys
http://www.mediafire.com/?e9dyyzgn8q3

 

Hi Scouser,

I tried the following:After program never got a yes to to "Program at address 0x7FE00000, size 0x200000? also couldn't see option to choose Tsop. Any ideas


Try this method using the same tsop file.


Connect JTAG and Power up EuroVox

Start JKEYS

Click on "Development Panel"
Click OK to ingore the warning.

** SEE BELOW IF YOU GET AN ERROR HERE **

If all goes well you will get into the development panel.

In the user functions box:

Type in the address: 80000000
Click on "Load to . . ."

Select the file "unlock_28FxxxC3.bin"

Click "Trigger User"

Close the current window.

Click on "Flash Programming"

Choose the model number as: DXD426RD (1 Chip-GLA)


In the section on the right:

Leave the box above set to "Full"

Click "Erase"

Select YES. This will take a minute to erase.

Click on "Program"

Select YES to "Program at address 0x7FE00000, size 0x200000?"

Choose your TSOP file

Sit and wait for OK to become active, then click it.

Close JKEYS and power the box down.

Disconnect your JTAG

Power the box on. If all has gone well then it should boot up ready for you to rescan for your channels.




*** If you get an error trying to get into the devleopment windows ****

Power the box down and run SkyMax v2.2
Power the box up
Press start.

This seems to reset the box when JKEYS cannot connect (DCU errors).

Close SkyMax and start JKEYS and try again.



Personally I went with Skymax first and then jkeys as it seems to work better.



SkyMax 2

http://www.mediafire.com/?8fzumnj1k9g

Jkeys
http://www.mediafire.com/?e9dyyzgn8q3

 

Hi Scouser,

I tried the following:After program never got a yes to to "Program at address 0x7FE00000, size 0x200000? also couldn't see option to choose Tsop. Any ideas


Try this method using the same tsop file.


Connect JTAG and Power up EuroVox

Start JKEYS

Click on "Development Panel"
Click OK to ingore the warning.

** SEE BELOW IF YOU GET AN ERROR HERE **

If all goes well you will get into the development panel.

In the user functions box:

Type in the address: 80000000
Click on "Load to . . ."

Select the file "unlock_28FxxxC3.bin"

Click "Trigger User"

Close the current window.

Click on "Flash Programming"

Choose the model number as: DXD426RD (1 Chip-GLA)


In the section on the right:

Leave the box above set to "Full"

Click "Erase"

Select YES. This will take a minute to erase.

Click on "Program"

Select YES to "Program at address 0x7FE00000, size 0x200000?"

Choose your TSOP file

Sit and wait for OK to become active, then click it.

Close JKEYS and power the box down.

Disconnect your JTAG

Power the box on. If all has gone well then it should boot up ready for you to rescan for your channels.




*** If you get an error trying to get into the devleopment windows ****

Power the box down and run SkyMax v2.2
Power the box up
Press start.

This seems to reset the box when JKEYS cannot connect (DCU errors).

Close SkyMax and start JKEYS and try again.



Personally I went with Skymax first and then jkeys as it seems to work better.



SkyMax 2

http://www.mediafire.com/?8fzumnj1k9g

Jkeys
http://www.mediafire.com/?e9dyyzgn8q3

 

Saga continues reading through all your problems are you sure you have a Red model as you seem to be able to erase the tsop but not write to it.

 

It came in red box. I presume it is ok.

 

Use Skymax and this tsop http://www.mediafire.com/?7bmmctpnylr as your other one may be corrupt.

 

Hi Scouser,

Done everthing. Seemed to load correctly then ran flash. But I still have the number 126 on box. When I key 1004 in box it then turns from 126 to 0000. However, nothing happens. When it tries to load its says no signal. Help. Please.

JLewis

 

Where getting somewhere. Is it powering up, if so got to menu,config, clear data. Clear all your channel data. Now you need to do a powerscan, you are in Dublin so I presume you are on N** true cable set symbol rate to 6887 and scan from 290 to 403. If you are on a different provider or MMDS please let me know.

 

When I turn it on it is on time. So press on button and i get 126 and tv says no signal.

 

Can you get into the menu?

 

Hi can any1 help i have a eurovox red 2007 n it keeps coming up no signal.. can any give me the software t put on it ..,.

 

HI Scouser,

I cannot get into menu.


JLewis

 

Hi Scouser , sorry for cutting across you but hope i can help.

@jlewis when you press menu on your remote what do you see on your tv , you should have a choice of preferences , channel manager , instalation , config. Can you get this far ? if you can do what scouser said earlier , go to config , clear data when that done you have to tune the box in by going to instalation from the main menu and doing a power scan. For the moment press the Menu on your remote and tell us what you see on your TV.

Again sorry Scouser , every little helps and jlewis we will get the box fixed for you