Eurovox flashing step by step.

Just a quick post to say thanks to all senior guys who help the less technically minded with updating firmware on eurovox max..just did it this morning & all works well now !
Thanks for your clear advice which makes it easy for even the like of me to follow & ofcourse, biggest thanks of all to authors of the firmware without whom we`d all be lost. Special thanks in my case to scouser & hitech who have been extremely helpful on this thread as well as other threads, hope xmas goes well for you !

 

hi,i have put new file in eurovox pvr and working fine but can i input codes manually, if so how? thanks.

 

hi-tech sorry for only getting back you now system info says
model dvb-xc box v tda
s/w ver 10 st4apr 18 2008
h/w ver 2.0t k5
bootstrap v001
sw build kuro

 

Hi hiteck, sorry for the delay, however i will be refreshing the screen evry so often, i shall be waiting for you to come back and help me out......thanks mate

 

@vidou
I wish LOL

@dublin007
Nice of you to say!

@nazarath
Have you tried your own subbed box on your feed to see if the channels are down as you say your neighbors are having the same problem, do they own the same box or is that on there own subbed box?

@foxyboy
Why would you want to if you have the latest firmware, Menu OK on language settings 1968 again 1968 pull left till nagraVision shows OR Menu then the yellow button.

 

im still having loads of trouble with this new update on the max v black 08
i used the uk fix on my box then a later one on my friends. i got the friends box to work without hassle mine has gone into the standby mode of death, just 4 dashes and a red light, i tried to update with all sorts of old and new firmwares, is it possible to downgrade to an older working version then re upgrade?
i tried to flash it using the ufl max v downloaders in plenty of different ways, like cycling the power to do it in boot mode as i read, i opened the box and pressed that little button trying to upload as well as cycling the power and pressing the button, im tryin to build a make shift Jtag with a paraller printer cable but i cant find a good schematic of the box to connect the cables to the pins on the pcb.
http://www.freewebs.com/jtagg/ iv used this as a guide but its different to what i have in my box though it states using a max v 08.
can anyone help with this or is the box dead? i intended to update with dnupman downloader with the 08tsop but cant get it to work with a null modem cable and cant figure out how to wire the jtag properly any help please?

 

Factory default then powerscan with these settings below.

Start 100.000
stop 850.000
Symbol rate 6887
Symbol rate 0000
symbol rate 0000
Step set to 8

Ok to start scan.

 

thanks hiteck, just curious.

 

Heno

Will this firmware download to your box. >> http://www.4shared.com/file/23838414/550f1243/UFL_MAX_V_06_09_07.html

 

another query, how to update starview pvr manually, my mate has one and said no secret menu on box or maybe he made some mistake?

 

no i tried it again there, and this was one of the fist flashes i went to when the box stopped working, the software used to instantly recognise the box now i have to choose ports, and tried a whole series of combintions with power cycles to no avail.

 

after a power cycle while having the loader runing it states the firmware is not fir for the reciver, seen it a few times in the last 2 days

 

@Heno
Try the reset button inside the box, with the box turned off start the UFL by pressing download, press the reset button and hold (Be careful where you put your fingers as your board will be live once powered up!), turn your box on then release the reset button.

@Foxyboy
Read here >> http://forums.afterdawn.com/thread_view.cfm/723020#4391614

 

Flashed a blue clone with genuine firmware from first page by mistake !! worked ok for a few days disconnected it but when reconnected displayed 6h6f now stuck on 0001 tried to flash with clone firmware when I get to download box says invalid file

 

Delete what your downloaded from page 1 and try them again.

 

[quote
@Heno
Try the reset button inside the box, with the box turned off start the UFL by pressing download, press the reset button and hold (Be careful where you put your fingers as your board will be live once powered up!), turn your box on then release the reset button.
/723020#4391614[/quote]
tried that there, same thing not fit for reveiver, then the LCD display danced abit as it usually does
any other ideas?

 

Well you did that quick!

Have some patience mate and keep trying, it may take a few tries.

Are you using the correct firmware > http://www.4shared.com/file/74569311/61af3b68/UFL_MAX_V_Autosort_5_12_08.html

For this

 

have the whole thing set up here in front of me
could it take a few goes? i would have thought that the one bash at it would do and if it dont work your potatoes aren't gonna boil
ill give it a few more goes now,
just check that we are both talking about the same thing
null modem cable(R232) from serial port to box, witht eh 6/9/07 loader pressing download then whilst holding the little button plug in the power then release the button yeah?

 

Heno look up mate, edited post.