Info regarding sound or other queries within (NO CODE REQUESTS/code POSTING)

If you have a Bad Flash with software have a Read of This might help

If you have a bad flash, switch it off then on at the back & make sure its on standby.
Then Flash as normal. This also applies to flashing (up & downloading) the channel data file.
If for some reason you cannot flash and have set and checked everything else such as ports and connections,
then you should switch off at the back wait a moment then on again. Then try to flash again.

If for some reason it won't go into standby and you see a constant moving green line.
you may want to wait to see if it goes into standby or switches on eventually or re-flash from this state
though it may not work. Some users have reported that flashing an older firmware 1st that was working,
then trying again may help. If your flash has failed or corrupted try again but 1st flash back the firmware
that was on before your failed flash. Re download the firmware just in case you had a corrupted file then try again.
If you do flash from the moving green line state at boot, you will see the % increase on the GTRom loader
software but not on the Starview. Toward the end of the flash you'll see a Flash Burning message in GTRom.
Make sure you wait until all is finished and you see the Download complete pop up message in GTRom.

Another method you can use to recover from a bad flash, eg. the box won't boot to standby and is stuck
in pre standby, either after about 3 or 4 moving green lines the box sticks with the green line not moving
at all or it keeps moving forever. If the box will NOT RE-FLASH as normal from on or standby, try this but it
may take a few goes to work.

Connect the box to the pc with your cable but switch it off at the back. Load the correct
firmware bin file into GTRom & set it to the correct com port, and select App file only then hit Download.
Only then switch on at the back to power on the box. It may take a few sec. so wait at least 30 sec.
(If it doesn't work 1st time try also waiting a couple of sec. to switch on after pressing download in the loader.) It may take more than 1 try to work, but eventually you'll see the loader kick in and the % bar increase. You won't see the % on the Starview though. Only green lines moving left to right. Towards the end of the flash you'll see a message in GTRom saying FLASH BURNING. Then it will reach 100% and wait for the download complete pop up box to appear & the box will reboot back to factory setup. You will have lost any channel data previously on the box & will need to rescan & switch on EMU and set the box up from scratch.

If you don't know the state of the box switch it on see what happens see if there already has been a channel
scan done before-meaning there are channels on it working or not. If so tune to an unencrypted channel as above
then standby then re-flash.

 

Its a cable receiver

 

thanks celt i will keep at it.

 

hi just wanted to know if anybody is haveing problems getting satan*a 1 ? or if anyone knows how i can get it?

 

Where abouts are you and what provider are you using ?

 

north west (wigan) and t*lewe*t

 

Try a manual scan on 827.000

If that fails , try an automatic scan

Check the bottom of your channel listing to see if its there

 

my starview box is gone down anyone got new codes

 

What does it say on the front of your box no signal if so check your cable

if not turn your box off at the back and turn on again and wait for it to update

as there has been no code change

 

I need the code as well its gone down again!!!
Can some1 post some codes ere plz...

 

it could be a cable break down so be patient and check the cable by putting it straight into the tv first

 

This happens sometimes in my area where the code has not changed officially but it gets changed in the box. I know its weird, but if you jus pop your box code in here then we'll probably be sorted.

 

try turning your box off and back on again and let it update

 

Keys changed

NTHELL - [07/12/2007]
KEY 00 = E9 77 45 79 70 41 80 CE
KEY 01 = 87 4C 47 FB FB 70 BD 17

 

hi guys starview has gone down in west london. southall

ive seen codes for n t hell, but im ex c+w has anyone got the new code yet .

its the hitman tomorrow i cant bear it,

thanks in advance

 

Try these ones

Starvi*w Codes : http://forums.afterdawn.com/thread_view.cfm/528527

 

tried the codes for ex c+w 07/12/07 but does not unscramble.

cant understand it ive manually input keys 5 times over last 2yrs with no probs , i know to store after each key and emu is on, this is really bugging me.

if its any help im in southall area ub2 postcode and im running 2.57e firmware which has been very stable till now.

please help its the hitman tomorrow

 

go to the codes on the bottom of my post and there is new codes there have a go at them and let me know thanks

 

hi fergus.

its working now thank you its my own stupid fault.
i was entering 01code because its always been 01 code in past but ive just entered 00 code and hey presto were back in business.

cheers anyway

 

ok happy days