Hi- I just updated to XP Pro from Windows '98... and have had no luck getting my burner to work in XP... Specs. System: P3, 500 MhZ, 128 MB Ram, Seagate 120 GB master drive. Burner Info.: Yamaha CRW6416SZ, SCSI Interface 16X Read 6X Write Firmware Version: 1.0d SCSI Specs. Adaptec AHA-2930CU PCI SCSI Controller Drivers: 1. aic78xx Adaptec Ultra SCSI miniport version 3.60a (Lab01_N.010510-0033) 2. Cdrom SCSI CD-Rom Driver version 5.1.2600.1106 (xpsp1.020828-1920) -I've done all critical windows updates and most all XP updates (except for a couple advanced networking updates for business/LAN) -I've updated my yamaha CD-R drive firmware and disabled 'autorun' and DMA settings before flashing the firmware. -I've tried 3 different software programs (Roxio Easy CD 5.5, Nero 6.0 and Hotburn)- none will work. -Roxio and Hotburn try to burn - Roxio creates an unreadable disc. Hotburn hits 99% complete and locks up. Nero locks up immediately and gives 'Unknown BurnPhase' error. Can anyone offer some advice? Thx.
hi did you install your burning apps "after installing XP" ???? if not uninstall and install again !!!!!! you may be on win98 drivers! also install adaptec.com ASPI layer! just go to there site and download and install and reboot! then let us know if it works ok! after those 2 things i would put "DMA" back on!!!!! Thx...
hi- I un-installed nero, disabled DMA on primary and secondary IDE's and dowloaded the Adaptec ASPI layer 4.71 for XP and installed. I then re-enabled DMA and rebooted - then re-installed Nero and proceeded to try and burn an audio cd... same 'Nero BurnPhase Error' when burning tried to begin... Should Autorun be back on in the registry maybe??? Any other ideas?
DMA should be enabled m8. In Device Manager>IDE DVD\CD-Rom, does it say where your Yamy is that "this device is working properly"? Any "yellow" markers? Yamaha is out of the cd burner business and it appears much burning software doesn't support Yamaha cd burners. Try The Firmware Page to be absolutly sure your using the latest firmware and if you are, well then... Autorun should be enabled if you play backups of Safedisc 2.8-2.9 Try burnatonce (freebie) and burn a data disc and see what happens. I would uninstall any packet write software (if applicable) for now. The Firmware Page: http://forum.rpc1.org/portal.php burnatonce 0.99a http://www.burnatonce.com/downloads/ Shoey __X_X_X_X_X_[small]Certified Computer Technician http://www.afterdawn.com/general/legal.cfm Mobo: MSI KT4VL-6712 CPU: AthlonXP Barton 2500+ Ram: 512 SD-DDR (PC-2700) nVidia GeForce4 MX440-8x Maxtor ATA\133 80 gig hd DVD-ROM: LiteOn LTD 165H CDRW: Memorex52MAXX 2452[/small]
Hi- Thanks for the info. Couple things... 1. I've read thru a number of pages on the forum that seem to indicate that the most current yahmaha firmware version for my drive (1.0d) is problematic... other member posts have said that I should revert back to firmware vers. 1.0c. (didn't see that recommendation related to my specific yammy model, but other models in the yammy family...)Think that would be worth a try? 2. ASPI: seems that my ASPI layer has conflicts and is corrupted... I updated the ASPI to the most current Adaptec version then installed Nero 6(which appears to have tried to overwrite with it's own ASPI layer)In any event, Nero InfoTool says the ASPI layer is corrupted... below is a complete InfoTool profile on my Yammy CD-R/RW drive, drivers, ASPI etc... can you take quick look and see if you see any other problems. Also, what's the best way to clear up my ASPI problem with Nero? --- Drive Information ----------------- Drive : YAMAHA CRW6416S Type : CD-RW Recorder Firmware Version : 1.0d Buffer Size : 2 MB Date : 30-05-00 Serial : ? Drive : H:\ Location : 2:3 Mechanism : Tray Read Speed : 16, 10, 6, 4, 2, 1 X Write Speed : 6, 4, 1 X Read CD Text : No Return C2 Pointers : No Read CD-R : Yes Read CD-RW : Yes Read DVD-ROM : No Read DVD-RAM : No Read DVD-R : No Read DVD-RW : No Read DVD+R : No Read DVD+RW : No Read Digital Audio : Yes Read CD+G : Yes Read VideoCD : Yes Write CD-R : Yes Write CD-RW : Yes Write DVD-R : No Write DVD-RW : No Write DVD+R : No Write DVD+RW : No Write DVD-RAM : No Buffer Underrun Protection : No Mount Rainier : No Modes : Packet, TAO, DAO, SAO, RAW SAO, RAW SAO 16, RAW SAO 96, RAW DAO 96 Disc Information (H:\) ------------------- Type : - no disc inserted - Interface Information --------------------- Adapter 1 --------- Description : Primary IDE Channel Driver Description : System32DRIVERS\atapi.sys Company : Microsoft Corporation Version : 5.1.2600.1106 (xpsp1.020828-1920) Description : IDE/ATAPI Port Driver Attached Devices Description Master : ST3120024A Type : Disk Drive DMA : On Description Slave : Maxtor 91741U4 Type : Disk Drive DMA : On Adapter 2 --------- Description Secondary IDE Channel Driver Description : System32\DRIVERS\atapi.sys Company : Microsoft Corporation Version : 5.1.2600.1106 (xpsp1.020828-1920) Description : IDE/ATAPI Port Driver Attached Devices Description : Master: TOSHIBA DVD-ROM SD-M1202 Type : CD-Rom Drive DMA : On Autorun : Off Description : Slave: IOMEGA ZIP 100 Type : Disk Drive DMA : Off Adapter 3 --------- Description : Adaptec AHA-2930CU PCI SCSI Controller Driver Description : System32\DRIVERS\aic78xx.sys Company : Microsoft Corporation Version : v3.60a (Lab01_N.010510-0033) Description : Adaptec Ultra SCSI miniport Attached Devices Description : ID 3 (0): YAMAHA CRW6416S 1.0d Type : CD-Rom Drive Autorun : Off Software Information -------------------- Operating System : Windows XP Professional (5.01.2600 Service Pack 1) ASPI : Nero Aspi Library 2.0.1.56 Ahead Software AG Description : Nero Burning ROM Version : 6, 0, 0, 0 Company : Ahead Software AG Version Check : Ok Hardware Information -------------------- CPU : Pentium III 500 MHz Bus Speed : 100 MHz Motherboard : BIOSTAR M6TWG System : BIOS : Award 6.00 PG Memory : 128 MB (6ns) Sound : Intel(r) Integrated Audio Video : Intel(r) 82810 Graphics Controller Driver Information ------------------ Driver : ac97intc Description : Intel(r) Integrated Controller Hub Audio Driver Version : 5.10.3523 built by: WinDDK Company : Intel Corporation Driver : aic78xx Description : Adaptec Ultra SCSI miniport Version : v3.60a (Lab01_N.010510-0033) Company : Microsoft Corporation Driver : Aspi32 Description : ASPI for WIN32 Kernel Driver Version : 4.71 (0002) built by: WinDDK Company : Adaptec Driver : atapi Description : IDE/ATAPI Port Driver Version : 5.1.2600.1106 (xpsp1.020828-1920) Company : Microsoft Corporation Driver : audstub Description : AudStub Driver Version : 5.1.2600.0 (XPClient.010817-1148) Company : Microsoft Corporation Driver : Cdfs Description : CD-ROM File System Driver Version : 5.1.2600.1106 (xpsp1.020828-1920) Company : Microsoft Corporation Driver : Cdrom Description : SCSI CD-ROM Driver Version : 5.1.2600.1106 (xpsp1.020828-1920) Company : Microsoft Corporation Driver : Disk Description : PnP Disk Driver Version : 5.1.2600.1106 (xpsp1.020828-1920) Company : Microsoft Corporation Driver : dmio Description : NT Disk Manager I/O Driver Version : 2600.0.503.0 Company : Microsoft Corp., Veritas Software Driver : dmload Description : NT Disk Manager Startup Driver Version : 2600.0.503.0 Company : Microsoft Corp., Veritas Software. Driver : Fastfat Description : Fast FAT File System Driver Version : 5.1.2600.1106 (xpsp1.020828-1920) Company : Microsoft Corporation Driver : Fdc Description : Floppy Disk Controller Driver Version : 5.1.2600.0 (XPClient.010817-1148) Company : Microsoft Corporation Driver : Flpydisk Description : Floppy Driver Version : 5.1.2600.1106 (xpsp1.020828-1920) Company : Microsoft Corporation Driver : Ftdisk Description : FT Disk Driver Version : 5.1.2600.0 (XPClient.010817-1148) Company : Microsoft Corporation Driver : gameenum Description : Game Port Enumerator Version : 5.1.2600.1106 (xpsp1.020828-1920) Company : Microsoft Corporation Driver : i8042prt Description : i8042 Port Driver Version : 5.1.2600.1106 (xpsp1.020828-1920) Company : Microsoft Corporation Driver : Imapi Description : IMAPI Kernel Driver Version : 5.1.2600.1106 (xpsp1.020828-1920) Company : Microsoft Corporation Driver : IntelIde Description : Intel PCI IDE Driver Version : 5.1.2600.1106 (xpsp1.020828-1920) Company : Microsoft Corporation Driver : IPSec Description : IPSec Driver Version : 5.1.2600.1106 (xpsp1.020828-1920) Company : Microsoft Corporation Driver : isapnp Description : PNP ISA Bus Driver Version : 5.1.2600.0 (xpclient.010817-1148) Company : Microsoft Corporation Driver : kmixer Description : Kernel Mode Audio Mixer Version : 5.1.2600.1106 (xpsp1.020828-1920) Company : Microsoft Corporation Driver : Modem Description : Modem Device Driver Version : 5.1.2600.0 (xpclient.010817-1148) Company : Microsoft Corporation Driver : MODEMCSA Description : Unimodem CSA Filter Version : 5.1.2600.0 (xpclient.010817-1148) Company : Microsoft Corporation Driver : MRxDAV Description : Windows NT WebDav Minirdr Version : 5.1.2600.0 (xpclient.010817-1148) Company : Microsoft Corporation Driver : NaiFiltr Description : N/A Version : N/A Company : N/A Driver : NdisTapi Description : NDIS 3.0 connection wrapper driver Version : 5.1.2600.0 (xpclient.010817-1148) Company : Microsoft Corporation Driver : Ndisuio Description : NDIS User mode I/O Driver Version : 5.1.2600.1106 (xpsp1.020828-1920) Company : Microsoft Corporation Driver : NdisWan Description : MS PPP Framing Driver (Strong Encryption) Version : 5.1.2600.1106 (xpsp1.020828-1920) Company : Microsoft Corporation Driver : Npfs Description : NPFS Driver Version : 5.1.2600.0 (xpclient.010817-1148) Company : Microsoft Corporation Driver : Ntfs Description : NT File System Driver Version : 5.1.2600.1106 (xpsp1.020828-1920) Company : Microsoft Corporation Driver : Parport Description : Parallel Port Driver Version : 5.1.2600.1106 (xpsp1.020828-1920) Company : Microsoft Corporation Driver : PartMgr Description : Partition Manager Version : 5.1.2600.0 (XPClient.010817-1148) Company : Microsoft Corporation Driver : ParVdm Description : VDM Parallel Driver Version : 5.1.2600.0 (XPClient.010817-1148) Company : Microsoft Corporation Driver : PCI Description : NT Plug and Play PCI Enumerator Version : 5.1.2600.1106 (xpsp1.020828-1920) Company : Microsoft Corporation Driver : PSched Description : MS QoS Packet Scheduler Version : 5.1.2600.1106 (xpsp1.020828-1920) Company : Microsoft Corporation Driver : Ptilink Description : Parallel Technologies DirectParallel IO Library Version : 1.10 (XPClient.010817-1148) Company : Parallel Technologies, Inc. Driver : Rasl2tp Description : RAS L2TP mini-port/call-manager driver Version : 5.1.2600.1106 (xpsp1.020828-1920) Company : Microsoft Corporation Driver : RasPppoe Description : RAS PPPoE mini-port/call-manager driver Version : 5.1.2600.0 (xpclient.010817-1148) Company : Microsoft Corporation Driver : Raspti Description : PTI DirectParallel(R) mini-port/call-manager driver Version : 5.1.2600.0 (xpclient.010817-1148) Company : Microsoft Corporation Driver : Rdbss Description : Redirected Drive Buffering SubSystem Driver Version : 5.1.2600.1106 (xpsp1.020828-1920) Company : Microsoft Corporation Driver : RDPCDD Description : RDP Miniport Version : 5.1.2600.0 (xpclient.010817-1148) Company : Microsoft Corporation Driver : rdpdr Description : Microsoft RDP Device redirector Version : 5.1.2600.1106 (xpsp1.020828-1920) Company : Microsoft Corporation Driver : redbook Description : Redbook Audio Filter Driver Version : 5.1.2600.1106 (xpsp1.020828-1920) Company : Microsoft Corporation Driver : rtl8139 Description : NDIS 5.0 driver Version : 5.396.0530.2001 Company : Realtek Semiconductor Corporation Driver : serenum Description : Serial Port Enumerator Version : 5.1.2600.0 (XPClient.010817-1148) Company : Microsoft Corporation Driver : Serial Description : Serial Device Driver Version : 5.1.2600.1106 (xpsp1.020828-1920) Company : Microsoft Corporation Driver : sr Description : System Restore Filesystem Filter Driver Version : 5.1.2600.1106 (xpsp1.020828-1920) Company : Microsoft Corporation Driver : Srv Description : Server driver Version : 5.1.2600.1193 (xpsp2.030327-2018) Company : Microsoft Corporation Driver : swenum Description : Plug and Play Software Device Enumerator Version : 5.3.0000000.900 built by: DIRECTX Company : Microsoft Corporation Driver : sysaudio Description : System Audio WDM Filter Version : 5.1.2600.1106 (xpsp1.020828-1920) Company : Microsoft Corporation Driver : Tcpip Description : TCP/IP Protocol Driver Version : 5.1.2600.1106 (xpsp1.020828-1920) Company : Microsoft Corporation Driver : TermDD Description : Terminal Server Driver Version : 5.1.2600.1106 (xpsp1.020828-1920) Company : Microsoft Corporation Driver : Update Description : Update Driver Version : 5.1.2600.0 (XPClient.010817-1148) Company : Microsoft Corporation Driver : usbhub Description : Default Hub Driver for USB Version : 5.1.2600.1243 (xpsp2.030702-2125) Company : Microsoft Corporation Driver : usbuhci Description : UHCI USB Miniport Driver Version : 5.1.2600.1243 (xpsp2.030702-2125) Company : Microsoft Corporation Driver : VolSnap Description : Volume Shadow Copy Driver Version : 5.1.2600.0 (XPClient.010817-1148) Company : Microsoft Corporation Driver : Wanarp Description : MS Remote Access and Routing ARP Driver Version : 5.1.2600.0 (xpclient.010817-1148) Company : Microsoft Corporation Driver : wdmaud Description : MMSYSTEM Wave/Midi API mapper Version : 5.1.2600.1106 (xpsp1.020828-1920) Company : Microsoft Corporation Driver : msvcrt.dll Version : 7.0.2600.1106 (xpsp1.020828-1920) Driver : msvcirt.dll Version : 7.0.2600.0 (xpclient.010817-1148) Driver : mfc42.dll Version : 6.00.8665.0 Driver : msvcp60.dll Version : 6.00.8972.0 Driver : ole32.dll Version : 5.1.2600.1263 (xpsp2.030819-2129) Driver : olepro32.dll Version : 5.0.5014 Driver : oledlg.dll Version : 1.0 (XPClient.010817-1148) Driver : advapi32.dll Version : 5.1.2600.1106 (xpsp1.020828-1920) Driver : comctl32.dll Version : 5.82 (xpsp1.020828-1920) Driver : setupapi.dll Version : 5.1.2600.1106 (xpsp1.020828-1920) Lower Filters ------------- Upper Filters ------------- Video Codecs ------------ Cinepak Codec by Radius : 1.10.0.6 Intel 4|2|0 Video V2.50 : 4.4.3400 Intel Indeo(R) Video R3.2 : Intel Indeo(R) Video R3.2 Intel Indeo® Video 4.5 : 4.51.16.03 Intel IYUV codec : 5.1.2600.0 (XPClient.010817-1148) Microsoft RLE : 5.1.2600.1106 (xpsp1.020828-1920) Microsoft Video 1 : 5.1.2600.0 (xpclient.010817-1148) Microsoft YUV : 5.3.0000000.900 built by: DIRECTX Microsoft YUV : 5.3.0000000.900 built by: DIRECTX Toshiba YUV Codec : 5.1.2600.0 (XPClient.010817-1148) Microsoft YUV : 5.3.0000000.900 built by: DIRECTX Microsoft H.263 Video Codec : 4.4.3400 Microsoft H.261 Video Codec : 4.4.3400 Indeo® video 5.10 : R.5.10.15.2.55 Audio Codecs ------------ Microsoft IMA ADPCM CODEC : 4.00.0.0 Microsoft ADPCM CODEC : 4.00.0.0 Microsoft CCITT G.711 A-Law and u-Law CODEC : 4.00.0.0 Microsoft GSM 6.10 Audio CODEC : 4.00.0.0 DSP Group TrueSpeech(TM) Software CODEC : 1.00.0.0 Microsoft G.723.1 CODEC : 1.02.0.1 Windows Media Audio : 4.02.0.0 Sipro Lab Telecom ACELP.net audio codec : 3.02.0.0 Indeo® audio software : 2.05.0.53 Fraunhofer IIS MPEG Layer-3 Codec (advanced): 1.09.1.49 Microsoft PCM Converter : 5.00.0.0 ASPI Information ---------------- System ASPI : ASPI installation is corrupted WNASPI32.DLL : 4.71 (0002) 45056 bytes July 17, 2002 ASPI32.SYS : 4.71 (0002) built by: WinDDK 16512 bytes July 17, 2002 Nero ASPI : ASPI is installed and working properly WNASPI32.DLL : 2.0.1.56 163910 bytes April 02, 2003
1. Nero uses its own aspi so you dont need to worry about that. 2. Just use the ASPICHK tool to see if your ASPI is installed correctly (dont trust Nero InfoTools!) 3. I reccommend ASPI 4.60 (1021) but you can also try the latest too (i think it is 4.72). Installing ASPI is a simple task requiring one reboot. For more information regarding ASPI see http://cd-rw.org/articles/archive/aspisetup.cfm
I uninstalled nero then I did the ASPICHCK and I have the following: component version size ASPI32.SYS 4.71.2 16512 bytes WOWPOST.EXE Not Installed WINASPI.DLL Not Installed WNASPI32.DLL 4.71.2 45056 bytes I then installed buratonce software and received the following errors when I tried to open the software... --- Error 0: Error occurred in: frmMain:scanbus App Version: 0.99a Windows Version: 5.1.2600 --- Error 424: Object required Error occurred in: frmMain:getDrivers App Version: 0.99a Windows Version: 5.1.2600 --- Error 424: Object required Error occurred in: frmMain:getDeviceIndex App Version: 0.99a Windows Version: 5.1.2600 --- and a few more errors... when I cliked thru the errors and opened the software, burnatonce could not see my burner... I am at my wits end... could be a new burner will be necessary... I don't think this one will work with XP...
Try this: 1. Uninstall EVERY SINGLE STINKIN burning app 2. Install Nero 3. Install Alcohol, CloneCD, Blindwrite, whatever 4. Install ASPI 4.60 (1021)
hi all you may need use "Force aspi layer" and its 4.60 do a search here or ask SHOEY on the CDR thread! Thx...
Yes - I did try forceaspi at one point as well... But I will give it another try... I did submit a support inquiry to yahmaha to see if they could offer any suggestions... Has anyone heard that I may need to revert back to an earlier version of Yahmaha firmware to solve the problem? I read a couple threads that were for another yahmaha model that said that firmware version 1.0d is problematic and that earlier version 1.0c should be installed... any truth to that? I have been searching for firmware 1.0c but have yet been able to find it... Also, the firmware indicates that 'Autorun' and DMA on all IDE's should be disabled for just about all versions of Windows before flashing (however, they make no mention of this being necessary for XP...) I've tried it both ways (disabled and not disabled)with no luck either way... should Autrun and DMA be disabled when flashing firmware to an XP op system? Thanks. CB
well - some progress I guess. I did ASPI check and noticed that a couple of the dll files were not installed for some reason... I unistalled all burning aps... I then re-flshed the firmware with DMA disabled on IDE's and Autorun turned off in registry. I rebooted and turned Autorun and DMA back on and rebooted again... Then, I Killed the exiting ASPI and dumped it and rebooted. I then installed force aspi and aspi check looked good. I then installed burnatonce and the program installed fine and opened with no errors. I then tried to burn an audio disc... the disc burned but the buffer only performed at 99% capacity and the disc was unreadable when I tried to open it. I then tried to burn a data disc and that process errored out immediately... Any next ideas?
Well I honestly believe this is a firmware issue. When you went to "The Firmware Page", did you download all firmware for your Yamy, flash, burn, errors? Try this and if you are unsuccessfull, then grab a Memorex 52MAXX cd burner (butta cutta) for backing up pc game protection (Safedisc 2.9& SecuROM 4.8.4) and cost less than the Asus 52x cd burner . Asus 52x is the better "all around burner" but the Memorex 52MAXX extracts audio fast enough, great dae accuracy, supports Mt. Rainer as well. The Firmware Page http://forum.rpc1.org/portal.php Go to download firmware>Yamaha cd burner Shoey
yes - I've tried so many combinations with the firmware... Reality is the last available firmware Vers. 1.0d says it's for XP (and NT, 2000, etc.) on the yahmaha download page but it was obviously developed/released w/o XP in mind, as the install dialogues make no mention of XP when you install and flash... just about every other Windows op system except xp is mentioned (including 2000 and NT) - so I think this was their last firmware release before exiting the burner business and it actually doesn't really work in XP... But it could be a SCSI/ASPI thing too I suppose... For the amount of time I've spent trying to figure this out, I could have bought a new burner... just want to make sure I don't chub up for a newbie and still encounter the same probs...
