KRYPTVIEW A750

thanks ben i will give it a try

 

hi guys, just took stockof my new a750, on MMDS N*l, havnt a clue what to do next. tried scanning.....nothing. i obviously need to do more stuff. please help i have a laptop with usb port, ialos have an adspter for the serial cable. not good on cumputers. need to be walked through the process many thanks

 

Hi guys, hopefully someone can help. Have my Kyptview up and running. It works fine but the picture quality isn't great. The picture looks jumpy as if there's a low frame rate. This is on all channels but becomes apparent when watching soccer or anything with fast moving objects. Does anyone know if this is a common problem? Is there any way to fix it? I've not had this problem with any other digital boxes.

Edit: Fixed it myself. Pressed the NTSC/PAL button a couple of times. That did the trick.

 

I'm getting the same problem as JONNYK82 on new kryptview box. Unfortunately your fix doesn't work on mine. Only happening on 2 stations Alibi and More4+1 the rest are fine.
I put my old starview back on and these stations are perfect. Can't figure it out.

 

Hi Fergus,
it's not the first time you've been asked this!
Where can i get my hands on one of the Kryptview boxes.
i'm in Dublin and enduring NT-Hell

 

Thanks in advance.
Fergus

 

pm sent

 

are you using a splitter on your incoming cable feed ??

 

hi guys i have a problem with my kryptview im tryin to load it when i press download it says download not requested any ideas

 

simple solution turn the box off at the back hit the download again then switch it on at the back and then it will

 

does anyone know how to access nagravision on the kryptview

 

had similar problem myself.Try factory reset and autoscan,i had to do this three times before it worked.

 

Hi JennieR,

Why would you want to ?

There is no need to enter codes or anything like that with the Kryptviews.

 

You can no longer enter codes into any boxes so i would forget about that idea as the kryptview does not have an emulator to switch on as once you put the firmware on your box it will work straight away

 

The answer is several pages back?

 

this is for information for the Kryptview Arnet A750 please try to keep it on this topic if possible i will try to answer your questions to the best of my ability

all you need for that box is on the end of my post in my signature

how to set it up etc
these are the Arnet boxes below

this is the older silver model


this is the latest model available

this is the cable needed below if you have a comport on your pc


this is what you need also if you dont have a comport


this is a VGA port



this is what you need on your laptop comport



This is the f connector adapter you need for your box



Radionics in Rialto Dublin stock them at 1.49euro each

or pick up a new cable with rf and push in connector most stores have these

[/quote]

TO MANUALLY INPUT FREQ FOR MMDS ONLY AS IT DONT SCAN THAT

network >>>> you put your provider in here ie NTL
channel you can start at 1
frequency >>>>>>>> your first number (ie) 362.000
symbol rate >>>>>> if not on 6887 change it to that
modulation >>>>>> 64 QAM it should be on that
channel search type always at >>>>> network

then press the YELLOW BUTTON ONLY

you will need to do this for each freq number you have to get it right

 

Nice bit of work there fergusrb, well done!

 

Thanks mate !!

 

Hello fergusrb,
Thanks for your help and info up to now. I hope you can help with my problem.
I am flashing and scanning 4 boxes new from *** and I have no problem with 3of them.
The 4th box will not scan and keeps going back to the installation screen.

I checked and found that after a factory default if you look in Manual scan + Channel + arrow right you will see 7 TPs by default . These are not relevant to Dublin N**. When you do an installation the system goes to a screen which says “Adding TPs”. The next screen should ask you to select the Network ID (N** Dub Legacy for example) and then it scans for all the available channels on that set of TPs for N** Dub.If you check back to Manual scan + Channel + arrow right you will see 19 TPs now . These are relevant to Dublin N**.

With the faulty box the “Select Network ID” screen does not appear and the scan is done on the default TPs with no channels found and it returns to the start “Installation" window.

I have tried many re-flashes and factory defaults but it’s the same every time.

Can anyone help with this ? should I just send it back ?
Has anyone had to send a box back and how did it work out?

A lot of questions but this is the best place to ask them.
Thanks in advance.