kryptView Updating & Scanning Tutorial

Thanks for your reply as always, I follow all instructions but my id list has 67 locations (no london)unlike the tut list of 199,Im currently watching most channels using portsmouth as id, cant figure it out watford or hackney,which is closer have loads missing,problem now is low frequency numbers ie.162.750, 170.750, signal strenth is 88 yet quality is 0-25 v bad freezing,is there anything I do about that? as for id areas I wish I could find one with all channels and good quality signal, thanks for all your help.

 

if your signal is good and your quality is as bad as that you are going to have lots of problems your quality should be on par with your signal only way you can find out your net id is to check your own subbed box its on it in the settings somwhere

 

Quality only bad on low frequencys,s*y s2 for example, 1,3,4,all perfect, what subbed box?

 

Here is the latest Net ID i can find hope these help you
Freshly scanned NetId list for exTw Areas.

NetId - 40961 (a001) - X_Barnsley R/E1
NetId - 40962 (a002) - X_Barnsley R/E2
NetId - 40963 (a003) - X_Barnsley R/E3
NetId - 40964 (a004) - X_Barnsley R/E4
NetId - 40965 (a005) - Knows R/E1
NetId - 40966 (a006) - Knows R/E2
NetId - 40967 (a007) - Preston R/E1
NetId - 40968 (a008) - Preston R/E2
NetId - 40969 (a009) - X_Gateshead R/E1
NetId - 40970 (a00a) - Aztec R/E1
NetId - 40971 (a00b) - Aztec R/E2
NetId - 40972 (a00c) - X_Trialist SE01 (Basildon)
NetId - 40973 (a00d) - X_Wolver R/E1
NetId - 40974 (a00e) - X_Wolver R/E2
NetId - 40975 (a00f) - X_Basild R/E1
NetId - 40976 (a010) - X_Basild R/E2
NetId - 40977 (a011) - X_Basild R/E3
NetId - 40978 (a012) - X_Basild R/E4
NetId - 40979 (a013) - X_Croydon
NetId - 40980 (a014) - X_Hayes
NetId - 40981 (a015) - X_Edinburgh R/E1
NetId - 40982 (a016) - X_Dundee (Edinburgh 2)
NetId - 40983 (a017) - X_Trialist LW01 (Hayes)
NetId - 40984 (a018) - X_Uddingston
NetId - 40985 (a019) - Haringey 600
NetId - 40986 (a01a) - Knowsley QA
NetId - 40987 (a01b) - Exeter BAU
NetId - 40988 (a01c) - Plymouth BAU
NetId - 40989 (a01d) - Trialist Exeter
NetId - 40990 (a01e) - X_Trialist YR02 (Barnsley 860)
NetId - 40991 (a01f) - QA Network Pres
NetId - 40992 (a020) - X_Pace Super Trialist 750
NetId - 40993 (a021) - X_Trialist BM01 (Birmingham)
NetId - 40994 (a022) - X_Trialist MD01 (Wolves RE/1)
NetId - 40995 (a023) - X_Trilaist MD02 (Wolves RE/2))
NetId - 40996 (a024) - Trialist Preston TDN
NetId - 40997 (a025) - Knowsley Resolve Ntwk
NetId - 40998 (a026) - X_Trialist YR01 (Barnsley 600)
NetId - 40999 (a027) - X_Perth
NetId - 41000 (a028) - BAU Pilot NID (Preston)
NetId - 41001 (a029) - Trialist NW01 ALPHA (Knowsley)
NetId - 41002 (a02a) - X_Trialist NE01 (Gateshead)
NetId - 41003 (a02b) - X_Trialist SC01 (EdinboroRE/1)
NetId - 41004 (a02c) - X_Trialist SC02 (Uddingston)
NetId - 41005 (a02d) - X_Trialist YR03PACE(Barns 600)
NetId - 41006 (a02e) - Trialist SW01 (Aztec)
NetId - 41007 (a02f) - X_Trialist LS01 (Croydon)
NetId - 41008 (a030) - Trialist Liverpool TDN
NetId - 41009 (a031) - X_Falkirk
NetId - 41010 (a032) - Haringey 750
NetId - 41011 (a033) - X_Birningham 750Mhz
NetId - 41012 (a034) - Trialist NW02 ALPHA (Preston)
NetId - 41013 (a035) - Trialist NW03 BETA (Knowsley)
NetId - 41014 (a036) - Trilaist LN01 (Harringey)
NetId - 41015 (a037) - X_Birmingham TDN
NetId - 41016 (a038) - Liverpool TDN
NetId - 41017 (a039) - X_Hayes TDN
NetId - 41018 (a03a) - Preston TDN
NetId - 41019 (a03b) - Trialist Plymouth
NetId - 41020 (a03c) - X_Crawley BAU
NetId - 41021 (a03d) - X_Crawley Trial
NetId - 41022 (a03e) - X_Birm TDN Trial
NetId - 41025 (a041) - X_Scottish Parliament
NetId - 41026 (a042) - Southport
NetId - 41500 (a21c) - DCC TEST

This is a complete and definitive list of all ACTIVE Netid's for the exTW area only. Note that once an area goes to N3 that it is switched to being a VM area and may or may not see the above NetId's

 

your providers box ?? if you dont have one of these this is why you are having problems with your cable as if you only pay for Broadband they reduce your incoming signal so you cant split it to use on your tv so if that is the case you will have to make do with what you have

 

I figured that using the latest 3.50 version I cannot get all channels, so I tried the first 3.02 and scanned on all networks and i got all channels, but not in order i.e. there are lots of bbc 1 coming up as 21** as opposed to 101. Then I don't know if this software related, server issue or virmin blocking my ip, but I flicked to baby tv and got scrambled, flicked back to previous working and got scrambled on all this happened again after reboot. Then I switched on my sub box and got please wait message on some normal channels. So i switched off the kv box, after half hour sub box was ok, put this on standby, turned on kv box no problems for hour. I have virgin Bband and tv on one cable splitting to modem, sub box and now kv box. I notice the picture is hazy. Do I need the sub box on?

 

yes you are using the all to scan on try reset your box and only scan on network and you wont have that problem that is why the tutorial is here for people to correctly scan there boxes

 

Thanks for your help but I dont undestand.

 

ok e45 are you saying that if i scan on the correct Netid then I won't get the scrambled channels issue. what about the problem with the splitter how do i resolve that. please can you be specific, sometimes you generalize your answers thats why its confusing. In the end it will only help others like ballybo etc

 

how many tv's is your house got
are they been split from the tv your box is connected to
b.band and cable been split should not make any difference

also yes if you scan the correct net id you should not have them problems

 

DO THIS ON DIRECT FEED ONLY NO SPLITTERS

Ok lets start at the start and follow this ok

1 menu >> installation >>> factory default your box password >>> 0000

2 unplug your box from the power socket wait 30 seconds and plug back in

3 next screen you see is the scan screen scroll down to auto and press ok

4 next screen you get put your provider on top leave the next one alone set to default NETWORK

5 press the green button on your remote only let the box scan

6 next screen you get list of net id find your one or nearest to you and highlight it and press ok

leave the box to scan let me know then when this is done what you get

 

do you have a box from your provider ?? yes ??? no ???

 

No,dont want anything to do with v

 

well then you will have to put up with the bad quality issues you are having as it down to the cable that you are having the problems and until you get that sorted you will have to live with the channels you have at the present time

 

Thanks for that info on finding out my netid. I got it off my sub box, maybe how to do it should be mentioned in the tutorial. I scanned on the 41069 lewisham net id and got all channels on ver 3.06. I downed this via software update feature. I have already come across a couple of problems with the kv. 1) Sometimes when you change from full picture to epg mini picture it freezes with a scrambled mini picture i.e a little box on its own. reboot fixes it.

2) If you click on audio button, select it, then exit and go to another channel, you get scrambled channels again. yesterday when it happened first time I turned it off with standby button, put it on again and got welcome screen which you get after factory reset, so I had to rescan again, but this happened again after with the audio button. Then I had to reboot from back switch.

 

How would I know if my box was being blocked by virgin? When I request audio or subtitles on say sky movies, the kv get this from the cs or from virgin. because I'm assuming that by requseting audio, some how virgin are seeing this request from me and therefore blocking me. In which case rebooting the kv box fixes this due to dhcp giving the kv a new ip.

 

please remember this is NOT a subbed box and as such will not do the same things your subbed one does as that is made specifically made for this purpose.

The box you are using is mainly to just give you Tv channels and not a lot more really

 

Thanks for that I thought it might be a feed problem, will look into it.

 

I know the kv box won't do what the sub box does. But as they have provided an audio button then you would assume that this would work without causing a problem such getting scrambled channels after. Most of these new firmware releases improve on and I hope fix problems found on previous firmware i.e. 3.02 etc. So by pointing out these issues I hope someone will be able to forward these bugs to the developers so that they can fix it. Otherwise why put an audio button on the remote?

 

remotes are just standard and the buttons are all ready are on them tbh as long as i had my channels the rest would not bother me