New Eurovox Software, NO CODES NEEDED

hi people,

first of all thanks everyone for the code updates !!!!!!

not sure if this is the new firmware or not but iv'e got it running on my eurovox max v 2008 and am currantly watching all the channels with no code. not sure how long it will last but been going strong now for about an hour. not sure but might go off in the morning when codes are changed but it's worth a go.

HERES THE LINK..........

www.dvbjunkieuk.com/downloads/UFL_MaxV_KUROv3_28_03_08_beta.exe

I'll keep u all updated on how long it lasts without the codes.


INSTRUCTIONS........

1; Connect cable input to the RF in socket on your eurovox, also connect box to your pc with null modem cable and also to your TV with scart. And lastly insert the power lead and switch on.

2; Open the dabbaman/dnupman program and confirm you have the correct com port, then select your firmware depending on the model of your box. ie; EV1 = eurovox with 1 scart, EV2 = eurovox with 2 scarts and EVMAX = latest model.

3; Apply power to the box and wait until (----) appears on the front. If your box has been flashed before it won’t display this, it'll just show 4 normal digits.

4; Click on download in the top half of the dabbaman/dnupman window. Then click start in the following window. If your box has not been flashed before it will say (system reset), when this happens reboot the box by removing and reapplying the power lead. If box has been flashed before do not remove power lead, just wait a moment and it will start downloading. If you are trying to flash an EV2 and you get a message saying "this firmware is not fit for your receiver", you must flash with the (EV2 for firmware error) flash.

5; The firmware should now be flashing to the box. (dnld) will appear flashing on the front display. The process takes a few minutes so be patient.

6; Once flash has completed (0000) will appear on front of box.

7; If this is the first time the box has been flashed your TV you should have the user installation screen with an info window saying (please check your cable status) press the exit button on your remote and proceed to step 8. If the box has been flashed before you will have to press the menu button then highlight config then clear data followed by pin no of 0000. In the next screen erase all channels should be highlighted then press the ok button twice. Once the "wait to delete all channels" window has disappeared press the exit button. Now highlight the installation menu and press ok followed by the pin no again.

8; Now press the blue button (powerscan) (the colour options on the remote and on screen differ for the EVMAX this will be the yellow button) this will open another smaller window with the heading "full power scan". If you are on the T/W network press the OK button, if however you are on the NT! network you will have to highlight within the window the first entry for symbol rate, usually (6.952) and edit this to (6.887)then press OK. The box will now scan all frequencies and find all active transponders for your area, and then it will scan them all for channels. This can be a long process, So go and have a cuppa and a read of your newspaper.

9; If everything has gone to plan you should now have channels, when you go to an encrypted channel you will usually get the message "please wait updating code" it is important you stay on this channel until it clears as this is the box intercepting the latest encryption keys. Allow a few minutes for this process to happen, I would say no longer than 10.

Now for the pain in the ass part, organizing your channels into favourites. The way i did it was to add all the general channels to (fav1) sports & movies to (fav2) kids & music to (fav3) and news & documentary to (fav4). Adult and ppv stuff I put in (fav2) after everything else. Once all this was done I changed the names of the fav groups within favourite manager. Remember your pin no to get into any settings is 0000.
I think it would be a good idea for all members to upload their channel data to the forum after everything has been organized into favourites, stating their area and provider.
This will make it easier for others in future. Also I have noticed that the CC's occasionally mess around with channels and transponders, in which case certain channels may be missing from time to time. By doing an auto scan (red button) within the installation menu you will pick these channels back up again and it shouldn't affect the layout of your favourites.

GOOD LUCK EVERONE !!!!!!

 

Just wondering if you can use an old CDF file with this to save having to reorganise favourites etc?

 

Just browsing the info and it says its got a new feature that automatically sorts all channels into fav groups. May be interesting have to wait and see

EDIT: ahhh i just noticed theres a newer firmware dated 10/4/08... didnt see the above one was earlier. Its the new version that has this feature.

 

Has anyone tried this, does it work ?

 

doesnt appear to work on ch***s yet? still stuck on updating code

 

Hi,

Loaded latest EV V Firmware, was stuck on updating for ages,

Had to enter latest codes to get channels??????

Anybody else tried in Dublin?

 

HACKER71 If you leave the channel on sky premiere it will update the code it took 10mins for mine to update im from dublin

 

Hi Typera12,

I'll try that thanks,

One of the other guys was saying that this firmware version dated 28/03/08 is not the answer to our current problem though. It just has better features???

 

yeh the new firmware dated the 10/04/08 is available to download here
http://www.freewebs.com/cableassist/eurovoxproducts.htm it works for me no problems

 

sorry guys,

newer release out.

download the bigmaq toolbar,



install update 10/04/08 for eurovox max v then follow install instructions above..............

all working fine, NO CODES NEEDED

regards,
carl.

 

Thanks. I'll let you know how I get on hacker 71

 

sorry guys i think u still need the codes just tried it and had to put in the codes used the new firmware 10/04/08. possibly the people who load up the new firmware had already entered in todays code earlier??? i hope i'm wrong

 

Worked here. Took less than 10 seconds to update the codes for an adult channel that went to channel number 1.

 

Can someone upload a channel file please as there are SO many channels to sort out at this hour of the day