New Eurovox TX For MMDS

no just the one power supply

 

Do you split the cable after the power supply and run it to the other box?
Probably sound a bit thick! but i'm asking on behalf of a friend, i've never even seen one of these boxes in operation!!

Thanks in advance

 

it was all done as i had multi room, just put the tx in place of the C****S boxes. the cable seems to be split in the attic, one of the splits cable goes downstairs into p.supply and then box and the other one goes into upstairs bedroom straight into box.signal fine on both boxes thinking of going mad and trying for a third

 

Yes I see what's happening.The power supply is powering the aerial.If you put a 3 way splitter in you should be fine.Just make sure it is like your existing 1 and allows dc through to the aerial.Why not chance it and go absolutely crazy and run a third box off the system!

 

the swords area is one of those places where
there is a hybred system in opperation, the normal eurovox max will work if you change the symbol rate to 6975 before auto scanning see below..
ON THE REMOTE
1 press menu & go to installation
2 select powerscan, normal mode
3 start freq 250.000 & stop freq 450.000
4 symbol rate 6875
5 press ok & wait until the box completes the scan .
6 when scan is complete the box will show the message
“UDATING PLEASE WAIT” in a few mins all channels
will become available.

 

hi can anyone tell me if setting up the TX is the same as setting up the MAX V thanks

 

Hi Folks, I’ve a question as I’m a newbie to this dodgy box malarkey

A mate of mine has got a Eurovox TX from a friend. He has the basic N*L package piped into his gaff ‘Dublin’. “From reading previous comments I'm not sure if this is mmds or analogue!”
He has tried scanning for channels however channels are scrambled. I believe it’s the firmware which came with the box initially ‘no flashing’.

So my question! Will the Eurovox TX work with this scenario?
Previous comments are suggesting its for C*****S mmds only!

Any info would be appreciated.

 

The eurovox TX is for CH**us MMDS only

 

Hi all.can anyone tell me if chorus Hybred system is used in Kilcock,wana know if i shud by eurovox max or tx
tanx

 

know of a few tx that went down today, they had to be re scaned to get them back... they have autorolled in recent weeks but not today for some reason. any idea why..thanks

 

hey,new to the thread! can anyone help have a eurovox max had over 130channels, now have none,trying the power scan nothing....

 

Please post your query here http://forums.afterdawn.com/thread_view.cfm/45/506556 as this thread is for the TX only.

 

do these work in cork?

i'm on c***** digital mmds, and thinking about investing in one.

if not, what are my other options?

thanks in advance

 

Yes,
The TX is your only man.

 

The Box - T is another option for C***** MMDS

 

are you an existing CH**us customer ? do you have an MMDS antenna on your house/roof ?
if so the Eurovox TX works a treat, I have set some up in different MMDS areas with no problems, can't speak for the BOX T,..the dreambox 500_t is another option but they are quite hard to come by.

 

Good evening everyone. What agreat site. I'm hoping someone can answer my questions:-
Is Ashbourne 1.a MMDS C****s N*L area , is it 2.pure cable or 3.Analogue?
Will a Eurovox 2008 work in Ashbourne if it's pure cable and if so can anyone please let me have the frequencies.
Has anyone in Ashbourne had any problems with this?
Many thanks in advance.

 

different box for C****S mmds and nthell mmds. do you have a square mesh aerial on roof. check your most recent bill to see what service ie digital or analouge

 

I did some testing around ashbourne with different boxes.
Ashbourne is Analogue only. It could be Chorus and NTL analogue I am not sure. I do know that near the village (crestwood etc) its chorus MMDS which would need the TX (assuming you have the mesh dish)
I am considering buying the Antenna and the TX for my folks.
Just need to do a bit more research on it first.