Hello everyone, I seem to have another problem with my super-(hardware)-setup. On ASUS P5B Deluxe Wifi/AP I have two Raptors on SATA1 and SATA2 working in RAID0 on Intel ICH8R. Subject for discussion: Optiarc AD-7170S, which is - as you know SATA, and attached to SATA4 port. Problem 1: in bios once you select "SATA mode" RAID, you loose all details on physical drives. Meaning I cannot change DMA and PIO for DVD-drive in bios. Problem 2: since in order to use RAID, Windows installs iastor.sys, the "ATAPI..." node in the device manager is not present. So all suggestions regarding enabling DMA are not valid for me. Moreover, I cannot even see DMA status in applications. There are no problems as such, just before booting from DVD PC hangs for 5 seconds, which is a little annoying, but not critical (I don't do system install every day). Started to think about this (potential) problem after Nero 8 damaged 2 DVD9 +R's during an attempt to create a UDF DVD (write error). Question: does this matter at all? Shall I look for a solution? What do you think, experts? Any opinion appreciated. -- Yakor
Thanks! Below is Nero log (full!). Remark: while trying to burn the disks I still had 1.00 firmware (for AD-7170S). After I had upgraded to 1.82, I never tried to re-burn the same compilation (4.5 EUR per try is too expensive in a marginal sense ====== *** Nero Burning ROM, History File *** ====== Windows XP 5.1 IA32 WinAspi: - NT-SPTI used Nero Version: 8.1.1.0 Internal Version: 8, 1, 1, 0 Recorder: <Optiarc DVD RW AD-7170S> Version: 1.00 - HA 1 TA 0 - 8.1.1.0 Adapter driver: <IDE> HA 1 Drive buffer : 2048kB Bus Type : default CD-ROM: <Optiarc DVD RW AD-7170S >Version: 1.00 - HA 1 TA 0 - 8.1.1.0 Adapter driver: <IDE> HA 1 === Scsi-Device-Map === DiskPeripheral : RAID0_SYS iaStor Port 0 ID 0 DMA: On DiskPeripheral : RAID0_DAT iaStor Port 0 ID 1 DMA: Off CdRomPeripheral : Optiarc DVD RW AD-7170S iaStor Port 0 ID 2 DMA: Off CdRomPeripheral : HB9101T DDO738M 1.0 ayt774x5 Port 1 ID 0 DMA: Off === CDRom-Device-Map === Optiarc DVD RW AD-7170S H: CdRom0 HB9101T DDO738M I: CdRom2 ======================= AutoRun : 1 Excluded drive IDs: WriteBufferSize: 83886080 (0) Byte BUFE : 0 Physical memory : 2047MB (2096204kB) Free physical memory: 1066MB (1091616kB) Memory in use : 47 Uncached PFiles: 0x0 Use Inquiry : 1 Global Bus Type: default (0) Check supported media : Disabled (0) 2.10.2007 UDF compilation 04:45:33 #1 Text 0 File SCSIPTICommands.cpp, Line 450 LockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL 04:45:33 #2 Text 0 File Isodoc.cpp, Line 6671 UDF document burn settings ------------------------------------------ Determine maximum speed : FALSE Simulate : FALSE Write : TRUE Finalize CD : FALSE Multisession : TRUE Multisession type: : Start multisession Burning mode : DAO Mode : 1 UDF Mode : pure UDF Options : automatic UDF Revision : 1.02 UDF Partition Type : physical 04:45:34 #3 Text 0 File Burncd.cpp, Line 3530 Turn on Disc-At-Once, using DVD media 04:45:35 #4 Text 0 File FilesystemSettingsValidator.cpp, Line 142 FS Settings: using validator 'CUDFSettingsValidatorDVD' ParamMode = 'automatic', changing UDF partition type from 'physical' to 'physical' Changing UDF revision from '1.02' to '1.02' 04:45:35 #5 Text 0 File DlgWaitCD.cpp, Line 307 Last possible write address on media: 4173823 (927:30.73, 8151MB) Last address to be written: 4048351 (899:38.01, 7906MB) 04:45:35 #6 Text 0 File DlgWaitCD.cpp, Line 319 Write in overburning mode: NO (enabled: CD) 04:45:35 #7 Text 0 File DlgWaitCD.cpp, Line 2972 Recorder: Optiarc DVD RW AD-7170S, Media type: DVD+R DL Disc Manufacturer ID: <RICOHJPN>, Media Type ID: <D01>, Product revision number: 67 Disc Application Code: 0, Extended Information Indicators: 3 04:45:35 #8 Text 0 File DlgWaitCD.cpp, Line 493 >>> Protocol of DlgWaitCD activities: <<< ========================================= 04:45:35 #9 Text 0 File ThreadedTransferInterface.cpp, Line 785 Setup items (after recorder preparation) 0: TRM_DATA_MODE1 () 2 indices, index0 (150) not provided original disc pos #0 + 4048352 (4048352) = #4048352/899:38.2 relocatable, disc pos for caching/writing not required/ required -> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 4048352 blocks [H: Optiarc DVD RW AD-7170S] -------------------------------------------------------------- 04:45:39 #10 Text 0 File ThreadedTransferInterface.cpp, Line 986 Prepare [H: Optiarc DVD RW AD-7170S] for write in CUE-sheet-DAO DAO infos: ========== MCN: "" TOCType: 0x00; Session Closed, disc not fixated Tracks 1 to 1: Idx 0 Idx 1 Next Trk 1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 8291024896, ISRC "" DAO layout: =========== ___Start_|____Track_|_Idx_|_CtrlAdr_|_____Size_|______NWA_|_RecDep__________ 0 | lead-in | 0 | 0x41 | 0 | 0 | 0x00 0 | 1 | 0 | 0x41 | 0 | 0 | 0x00 0 | 1 | 1 | 0x41 | 4048352 | 0 | 0x00 4048352 | lead-out | 1 | 0x41 | 0 | 0 | 0x00 04:45:39 #11 Text 0 File SCSIPTICommands.cpp, Line 240 SPTILockVolume - completed successfully for FSCTL_LOCK_VOLUME 04:45:39 #12 Text 0 File Burncd.cpp, Line 4316 Caching options: cache CDRom or Network-Yes, small files-No (<64KB) 04:45:39 #13 Phase 24 File dlgbrnst.cpp, Line 1764 Caching of files started 04:45:39 #14 Text 0 File Burncd.cpp, Line 4435 Cache writing successful. 04:45:39 #15 Phase 25 File dlgbrnst.cpp, Line 1764 Caching of files completed 04:45:39 #16 Phase 36 File dlgbrnst.cpp, Line 1764 Burn process started at 8x (11,080 KB/s) 04:45:39 #17 Text 0 File ThreadedTransferInterface.cpp, Line 2735 Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0 04:45:39 #18 Text 0 File DVDPlusDualLayer.cpp, Line 671 L0 Data Zone Capacity not set. Max LBA L0 2086911 (1FD7FFh, 4075MB), next writable address 0 (0h, 0MB) 04:45:39 #19 CDR -1205 File DVDPlusDualLayer.cpp, Line 687 Burning Layer 1 04:45:39 #20 Text 0 File DVDPlusDualLayer.cpp, Line 697 Start writing layer 1 at address 0 (0h) Recording mode: unknown Recording Mode 04:45:39 #21 Text 0 File Cdrdrv.cpp, Line 10026 ---- Disc Structure: Physical Format Information (00h) ---- Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050 Book Type: DVD-ROM (0), Part Version: 1.0x (1) Disc Size: 120 mm, Maximum Rate: <not specified> (F h) Number of Layers: 2, Track Path: Opposite Track Path (OTP), Layer Type: recordable Linear Density: 0,293 um/bit, Track Density: 0,74 um/track Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW) End Physical Sector Number of Data Area: FCFFFF h End Physical Sector Number in Layer 0: 22D7FF h (LBN: 1FD7FF h, 4075 MB) Data in Burst Cutting Area (BCA) does not exist Twin Format Flag: 0 Media Specific [16..783]: 00 00 03 52 49 43 4F 48 - 4A 50 4E 44 30 31 43 40 ...RICOHJPND01C@ 25 25 37 10 00 2C 6C 00 - 2C 6C 20 1F 0C 0C 14 14 %7..,l.,l...... 02 01 01 20 00 20 1F 0C - 0C 14 14 02 01 01 20 00 ................ 04 00 33 7B 5C 00 25 69 - 3A 26 1C 0A 0B 20 02 01 ..3{\.65001:&...... 01 00 00 58 62 42 26 1C - 0A 0B 20 02 01 01 00 5F ...XbB&........_ 84 00 00 43 66 3E 26 1C - 0A 0B 20 02 01 01 00 00 ...Cf>&......... 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ E1 0F 32 10 00 03 00 00 - 00 FC FF FF 00 22 D7 FF ..2..........".. 00 00 03 52 49 43 4F 48 - 4A 50 4E 44 30 31 43 40 ...RICOHJPND01C@ 25 25 37 15 00 34 6E 00 - 34 6E 1A 1A 0C 0C 0E 0E %7..4n.4n...... 00 00 00 10 00 1A 1A 0C - 0C 0E 0E 00 00 00 10 00 ................ 04 00 33 7B 5C 00 33 66 - 40 19 10 05 04 10 00 00 ..3{\.3f@....... 00 00 00 55 6A 32 24 16 - 09 08 20 00 00 00 00 05 ...Uj2$......... 84 00 00 48 6E 28 24 16 - 09 08 20 00 00 00 00 00 ...Hn($......... 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 04:45:39 #22 Text 0 File DVDR.cpp, Line 6748 Drive: Optiarc DVD RW AD-7170S Book Type request [NEC]: DVD-ROM, write to RAM select Book Type setting from RAM Changing the Book Type was finished successfully, return code 0 04:45:39 #23 CDR -1207 File DVDR.cpp, Line 6452 Book Type automatically set to: DVD-ROM 04:45:39 #24 Text 0 File DVDPlusRW.cpp, Line 675 Start write address at LBA 0 DVD high compatibility mode: No 04:45:39 #25 Text 0 File ThreadedTransfer.cpp, Line 268 Pipe memory size 83836800 04:54:35 #26 SPTI -1135 File SCSIPassThrough.cpp, Line 181 CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1135) Sense Key: 0x03 (KEY_MEDIUM_ERROR) Sense Code: 0x0C Sense Qual: 0x00 CDB Data: 0x2A 00 00 1F CF 40 00 00 20 00 00 00 Sense Area: 0x70 00 03 00 00 00 00 0A 00 00 00 00 0C Buffer x0f4237c0: Len x10000 0x2B 76 30 5A 29 0D 6F 28 89 32 0D A1 65 62 53 BD 0x4C AF 64 47 86 F4 DA B6 72 03 90 DE FC AA C1 10 0x2B A4 42 4B F3 35 EE C9 12 F9 B0 1C 16 7B 67 06 04:54:35 #27 CDR -1135 File Writer.cpp, Line 306 Write error H: Optiarc DVD RW AD-7170S 04:54:36 #28 SPTI -1135 File SCSIPassThrough.cpp, Line 181 CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1135) Sense Key: 0x03 (KEY_MEDIUM_ERROR) Sense Code: 0x0C Sense Qual: 0x00 CDB Data: 0x5B 01 01 00 00 01 00 00 00 00 00 00 Sense Area: 0x70 00 03 00 00 00 00 0A 00 00 00 00 0C 04:54:36 #29 Text 0 File DVDPlusRW.cpp, Line 935 EndDAO: Last written address 2084672 04:54:36 #30 Text 0 File DVDR.cpp, Line 6748 Drive: Optiarc DVD RW AD-7170S Book Type request [NEC]: DVD-ROM, write to RAM select Book Type setting from RAM Changing the Book Type was finished successfully, return code 0 04:54:36 #31 Phase 38 File dlgbrnst.cpp, Line 1764 Burn process failed at 8x (11,080 KB/s) 04:54:36 #32 Text 0 File SCSIPTICommands.cpp, Line 287 SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME 04:54:40 #33 Text 0 File Cdrdrv.cpp, Line 11276 DriveLocker: UnLockVolume completed 04:54:40 #34 Text 0 File SCSIPTICommands.cpp, Line 450 UnLockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL Existing drivers: Registry Keys: HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option) ====== *** Nero Burning ROM, History File *** ====== -- Yakor
Hi ;-) Not too familar with your mobo. But a lot of folk have problems with the Intel ICH8R. For ODD's to work properly you cannot use RAID of any kind. Doesn't the bios let you select individually? If you cannot do this, then you would have to consider a PCI SATA controller card. This shouldn't be necessary as it would be all over the net by now.
Trying to burn at the max rate for the media and the writer is your problem. Also the media you have is not the best. Which, if you are paying the price for dual layer, stick ewith the best. Check the rating on your media. http://www.videohelp.com/dvdmedia?dvdmediadvdridsearch=RICOHJPND01 Compare to these. http://www.videohelp.com/dvdmedia?dvdmediadvdridsearch=MKM.....003 http://www.videohelp.com/dvdmedia?dvdmediadvdridsearch=MKM.....001 Burn at half the media's rated speed is the rule for burning. If your firmware is old stay away from the max speed on newer meida.
56delray Thanks for comments and encouraging. However, I didn't quite get the cavils from your last post. You seem to critisize the media I've chosen (quote: "Also the media you have is not the best"). At the same time the link you provide gives the following rating to it: Plays on 1 DVD Players Plays not on 0 DVD Players Burn Reliability is Good DVD Reliability is Good PC Reliability is Good Console Reliability is N/A Which is the best in the first link among the 13 listed there (together with BENQ, which has absolutely the same qualities as my TDK) and the 3rd among all provided links (yielding only to Verbatim and Dynex, which I've never seen, by the way). Was it a mistake or did you want to say something else? You might be right. I thought differently, becasue some time ago I've read another materials (numerous), which stated that burning at lower speeds might be even worth. Shall I really stick to this rule? As you have seen, I have 1.82 now, which cannot be newer. Can I burn at max speed from now on? Still, the question remains: what to do with DMA and shall I really consider an option of buying a third-party RAID card so that to let my SATA Optiarc rest on normal IDE channel? zebadee mobo is quite widespread, as well as its problems This is something new to me. This mobo has also a J-Micron RAID controller, which, though, is designed to work with one external SATA drive. Before going to integrated Intel's RAID, I've read thousand of opinions, which helped me decide in favor of ICH8R. Could you, perhaps, clarify or give links what exactly problems people refer to? --Yakor
Hi ;-) As I said not too familiar with your mobo, only that folk have problems with ICH8R. Not sure what. But I do seem to recall that many are told to use the J-Micron RAID controller. So must be something relating to switching from one to the other. Anyway I still feel that my understanding that ODD's won't function properly if RAID is selected is correct.
OK guys, The "DMA-RAID" problem has been partially solved. Found an "original" way out: attached DVD drive to the only on-board connector of J-Micron SATA/PATA controller and set it in AHCI mode. Now there is no delay when booting from DVD! However, in device manager, it's DMA 2. And according to some posts in this forum it should be 4. I can't control this in BIOS, since it's now JMicron's responsibility. Shall I try to burn that unlucky session again? -- Yakor
Write speeds for the 7170. DVD+,-R:18x max. DVD-RW:6x max. DVD +RW:8x max. DVD+,-R DL:8x max. Now say in the future they have 16x DL media. You still might not want to burn at 8x with a older writer and firmware. As to the links: The first link for RICOHJPN D01. Which is what you have no matter who's name is on the label. There are 15 comments of poor burn reliabilty, 3 mixed and 7 good. The next link for MKM003 8x media has 12 good comments. The last link for MKM01 2.4x media has 6 mixed and 157 good comments. Of these choices the best results are from the 2.4x DL media. Now this may be different for other writers. The worst writers are OEM versions because the firmware is not updated as new media invented. So good bet would be to burn MKM003 at 4x. The safe bet would be MKM01 at 1x or 2.4x.
56delray, New firmware, another SATA, ISO session, result = the same! Just spoiled another media. Followed your advise, recoded at 4x. The stall happens somewhere in the middle. Cannot get to second layer?? I paste the log below. Sent a request to Nero, but they seem to be also puzzled. What can be worng??? -- Yakor ======================= Windows XP 6.0 IA32 WinAspi: - NT-SPTI used Nero Version: 8.1.1.0 Internal Version: 8, 1, 1, 0 Recorder: <Optiarc DVD RW AD-7170S> Version: 1.82 - HA 1 TA 0 - 8.1.1.0 Adapter driver: <IDE> HA 1 Drive buffer : 2048kB Bus Type : default CD-ROM: <Optiarc DVD RW AD-7170S >Version: 1.82 - HA 1 TA 0 - 8.1.1.0 Adapter driver: <IDE> HA 1 === Scsi-Device-Map === DiskPeripheral : RAID0_SYS iaStorV Port 0 ID 0 DMA: On DiskPeripheral : RAID0_DAT iaStorV Port 0 ID 1 DMA: Off === CDRom-Device-Map === Optiarc DVD RW AD-7170S F: CdRom0 ======================= AutoRun : 1 Excluded drive IDs: WriteBufferSize: 83886080 (0) Byte BUFE : 0 Physical memory : 2046MB (2095552kB) Free physical memory: 976MB (999500kB) Memory in use : 52 % Uncached PFiles: 0x0 Use Inquiry : 1 Global Bus Type: default (0) Check supported media : Disabled (0) 7.10.2007 ISO compilation 04:27:37 #1 Text 0 File SCSIPTICommands.cpp, Line 450 LockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL 04:27:37 #2 Text 0 File Isodoc.cpp, Line 6671 Iso document burn settings ------------------------------------------ Determine maximum speed : TRUE Simulate : FALSE Write : TRUE Finalize CD : FALSE Multisession : TRUE Multisession type: : Start multisession Burning mode : DAO Mode : 1 ISO Level : 1 (Max. of 11 = 8 + 3 char) Character set : ISO 9660 Joliet : TRUE Allow pathdepth more than 8 directories : TRUE Allow more than 255 characters in path : TRUE Write ISO9660 ;1 file extensions : TRUE 04:27:38 #3 ISO9660GEN -11 File Geniso.cpp, Line 3347 First writeable address = 0 (0x00000000) 04:27:38 #4 Text 0 File Burncd.cpp, Line 3530 Turn on Disc-At-Once, using DVD media 04:27:38 #5 Text 0 File FilesystemSettingsValidator.cpp, Line 142 FS Settings: using validator 'CUDFSettingsValidatorDVD' ParamMode = 'automatic', changing UDF partition type from 'physical' to 'physical' Changing UDF revision from '1.02' to '1.02' 04:27:38 #6 Text 0 File DlgWaitCD.cpp, Line 307 Last possible write address on media: 4173823 (927:30.73, 8151MB) Last address to be written: 4044927 (898:52.27, 7900MB) 04:27:38 #7 Text 0 File DlgWaitCD.cpp, Line 319 Write in overburning mode: NO (enabled: CD) 04:27:38 #8 Text 0 File DlgWaitCD.cpp, Line 2972 Recorder: Optiarc DVD RW AD-7170S, Media type: DVD+R DL Disc Manufacturer ID: <RICOHJPN>, Media Type ID: <D01>, Product revision number: 67 Disc Application Code: 0, Extended Information Indicators: 3 04:27:38 #9 Text 0 File DlgWaitCD.cpp, Line 493 >>> Protocol of DlgWaitCD activities: <<< ========================================= 04:27:38 #10 Text 0 File ThreadedTransferInterface.cpp, Line 785 Setup items (after recorder preparation) 0: TRM_DATA_MODE1 () 2 indices, index0 (150) not provided original disc pos #0 + 4044928 (4044928) = #4044928/898:52.28 relocatable, disc pos for caching/writing not required/ required -> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 4044928 blocks [F: Optiarc DVD RW AD-7170S] -------------------------------------------------------------- 04:27:49 #11 Text 0 File ThreadedTransferInterface.cpp, Line 986 Prepare [F: Optiarc DVD RW AD-7170S] for write in CUE-sheet-DAO DAO infos: ========== MCN: "" TOCType: 0x00; Session Closed, disc fixated Tracks 1 to 1: Idx 0 Idx 1 Next Trk 1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 8284012544, ISRC "" DAO layout: =========== ___Start_|____Track_|_Idx_|_CtrlAdr_|_____Size_|______NWA_|_RecDep__________ 0 | lead-in | 0 | 0x41 | 0 | 0 | 0x00 0 | 1 | 0 | 0x41 | 0 | 0 | 0x00 0 | 1 | 1 | 0x41 | 4044928 | 0 | 0x00 4044928 | lead-out | 1 | 0x41 | 0 | 0 | 0x00 04:28:09 #12 Text 0 File SCSIPTICommands.cpp, Line 264 Error on LockVolume: Access is denied. 04:28:09 #13 Text 0 File SCSIPTICommands.cpp, Line 287 SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME 04:28:10 #14 Text 0 File SCSIPTICommands.cpp, Line 240 SPTILockVolume - completed successfully for FSCTL_LOCK_VOLUME 04:28:10 #15 Text 0 File Burncd.cpp, Line 4316 Caching options: cache CDRom or Network-Yes, small files-No (<64KB) 04:28:10 #16 Phase 24 File dlgbrnst.cpp, Line 1764 Caching of files started 04:28:10 #17 Text 0 File Burncd.cpp, Line 4435 Cache writing successful. 04:28:10 #18 Phase 25 File dlgbrnst.cpp, Line 1764 Caching of files completed 04:28:10 #19 Phase 28 File dlgbrnst.cpp, Line 1764 Speed measurement started 04:28:10 #20 Text 0 File ThreadedTransferInterface.cpp, Line 2735 Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0 04:28:10 #21 Text 0 File ThreadedTransfer.cpp, Line 268 Pipe memory size 590400 04:29:40 #22 Text 0 File WriterStatus.cpp, Line 113 <F: Optiarc DVD RW AD-7170S> start writing Lead-Out at LBA 4044928 (3DB880h), length 0 blocks 04:29:40 #23 Phase 29 File dlgbrnst.cpp, Line 1713 Speed measurement completed: 64.8x (89,516 KB/s) 04:29:40 #24 Phase 36 File dlgbrnst.cpp, Line 1764 Burn process started at 4x (5,540 KB/s) 04:29:40 #25 Text 0 File ThreadedTransferInterface.cpp, Line 2735 Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0 04:29:40 #26 Text 0 File DVDPlusDualLayer.cpp, Line 495 Disc finalized, LBA total Image size: 4044928 (7900MB), Last LBA L0: 2022463 (3950MB) 04:30:11 #27 SPTI -1066 File SCSIPassThrough.cpp, Line 181 CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1066) Sense Key: 0x05 (KEY_ILLEGAL_REQUEST) Sense Code: 0x24 Sense Qual: 0x00 CDB Data: 0xAD 00 00 00 00 00 00 21 08 04 00 00 Sense Area: 0x70 00 05 00 00 00 00 0A 00 00 00 00 24 00 00 C0 00 07 Buffer x0c011100: Len x804 04:30:11 #28 Text 0 File DVDPlusDualLayer.cpp, Line 660 L0 Data Zone Capacity set to 2022464 (1EDC40h, 3950MB) -> OK, confirmed setting 04:30:11 #29 CDR -1205 File DVDPlusDualLayer.cpp, Line 687 Burning Layer 1 04:30:11 #30 Text 0 File DVDPlusDualLayer.cpp, Line 697 Start writing layer 1 at address 0 (0h) Recording mode: unknown Recording Mode 04:30:11 #31 Text 0 File Cdrdrv.cpp, Line 10026 ---- Disc Structure: Physical Format Information (00h) ---- Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050 Book Type: DVD+R DL (14), Part Version: 1.0x (1) Disc Size: 120 mm, Maximum Rate: <not specified> (F h) Number of Layers: 2, Track Path: Opposite Track Path (OTP), Layer Type: recordable Linear Density: 0,293 um/bit, Track Density: 0,74 um/track Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW) End Physical Sector Number of Data Area: FCFFFF h Data in Burst Cutting Area (BCA) does not exist Disc Application Code: 0 / 0 h Extended Information indicators: 3 h Disc Manufacturer ID: RICOHJPN Media type ID: D01 Product revision number: 67 Number of Physical format information bytes in use in ADIP up to byte 63: 64 Media Specific [16..783]: 00 00 03 52 49 43 4F 48 - 4A 50 4E 44 30 31 43 40 ...RICOHJPND01C@ 25 25 37 10 00 2C 6C 00 - 2C 6C 20 1F 0C 0C 14 14 %%7..,l.,l...... 02 01 01 20 00 20 1F 0C - 0C 14 14 02 01 01 20 00 ................ 04 00 33 7B 5C 00 25 69 - 3A 26 1C 0A 0B 20 02 01 ..3{\.%i:&...... 01 00 00 58 62 42 26 1C - 0A 0B 20 02 01 01 00 5F ...XbB&........_ 84 00 00 43 66 3E 26 1C - 0A 0B 20 02 01 01 00 00 ...Cf>&......... 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ E1 0F 32 10 00 03 00 00 - 00 FC FF FF 00 22 D7 FF ..2..........".. 00 00 03 52 49 43 4F 48 - 4A 50 4E 44 30 31 43 40 ...RICOHJPND01C@ 25 25 37 15 00 34 6E 00 - 34 6E 1A 1A 0C 0C 0E 0E %%7..4n.4n...... 00 00 00 10 00 1A 1A 0C - 0C 0E 0E 00 00 00 10 00 ................ 04 00 33 7B 5C 00 33 66 - 40 19 10 05 04 10 00 00 ..3{\.3f@....... 00 00 00 55 6A 32 24 16 - 09 08 20 00 00 00 00 05 ...Uj2$......... 84 00 00 48 6E 28 24 16 - 09 08 20 00 00 00 00 00 ...Hn($......... 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 04:30:11 #32 Text 0 File DVDR.cpp, Line 6748 Drive: Optiarc DVD RW AD-7170S Book Type request [NEC]: DVD-ROM, write to RAM select Book Type setting from RAM Changing the Book Type was finished successfully, return code 0 04:30:11 #33 CDR -1207 File DVDR.cpp, Line 6452 Book Type automatically set to: DVD-ROM 04:30:11 #34 Text 0 File DVDPlusRW.cpp, Line 675 Start write address at LBA 0 DVD high compatibility mode: Yes 04:30:11 #35 Text 0 File ThreadedTransfer.cpp, Line 268 Pipe memory size 83836800 04:42:17 #36 SPTI -1135 File SCSIPassThrough.cpp, Line 181 CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1135) Sense Key: 0x03 (KEY_MEDIUM_ERROR) Sense Code: 0x0C Sense Qual: 0x00 CDB Data: 0x2A 00 00 1E 92 40 00 00 20 00 00 00 Sense Area: 0x70 00 03 00 00 00 00 0A 00 00 00 00 0C Buffer x1dfe3cc0: Len x10000 0x49 78 63 81 78 7A 70 79 9F 18 82 84 7F 86 7B 88 0x08 EC 07 13 40 04 C1 92 94 8C 86 92 89 8E 19 13 0xA0 61 81 98 90 C9 8C 97 8F 91 97 94 19 90 8F 8C 04:42:17 #37 CDR -1135 File Writer.cpp, Line 306 Write error F: Optiarc DVD RW AD-7170S 04:42:18 #38 SPTI -1135 File SCSIPassThrough.cpp, Line 181 CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1135) Sense Key: 0x03 (KEY_MEDIUM_ERROR) Sense Code: 0x0C Sense Qual: 0x00 CDB Data: 0x5B 01 01 00 00 01 00 00 00 00 00 00 Sense Area: 0x70 00 03 00 00 00 00 0A 00 00 00 00 0C 04:42:18 #39 SPTI -1176 File SCSIPassThrough.cpp, Line 181 CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1176) Sense Key: 0x05 (KEY_ILLEGAL_REQUEST) Sense Code: 0x72 Sense Qual: 0x03 CDB Data: 0x5B 01 05 00 00 00 00 00 00 00 00 00 Sense Area: 0x70 00 05 00 00 00 00 0A 00 00 00 00 72 03 04:42:18 #40 Text 0 File DVDPlusRW.cpp, Line 935 EndDAO: Last written address 2003520 04:42:18 #41 Text 0 File DVDR.cpp, Line 6748 Drive: Optiarc DVD RW AD-7170S Book Type request [NEC]: DVD-ROM, write to RAM select Book Type setting from RAM Changing the Book Type was finished successfully, return code 0 04:42:18 #42 CDR -1176 File WriterStatus.cpp, Line 162 Session fixation error F: Optiarc DVD RW AD-7170S 04:42:18 #43 TRANSFER -24 File WriterStatus.cpp, Line 162 Could not perform end of Disc-at-once 04:42:18 #44 Phase 38 File dlgbrnst.cpp, Line 1764 Burn process failed at 4x (5,540 KB/s) 04:42:18 #45 Text 0 File SCSIPTICommands.cpp, Line 287 SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME 04:42:22 #46 Text 0 File Cdrdrv.cpp, Line 11276 DriveLocker: UnLockVolume completed 04:42:22 #47 Text 0 File SCSIPTICommands.cpp, Line 450 UnLockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL Existing drivers: Registry Keys: HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon
Hello, It seems that something wrong either with the drive or with the media or with their compatibility. In any case, wasted money. that was the 4th an the last blank from that box. Burned in imgbirn, at 2.4, buit an iso beforehand. Everything as instructed. Result below. Any suggestions? Shall I try Fujifilm now (it's the last of my DVD9's stock) I 23:32:52 ImgBurn Version 2.3.2.0 started! I 23:32:52 Microsoft Windows Vista Ultimate Edition (6.0, Build 6001 : Service Pack 1, v.275) I 23:32:52 Total Physical Memory: 2,095,552 KB - Available: 959,252 KB I 23:32:52 Initialising SPTI... I 23:32:52 Searching for SCSI / ATAPI devices... I 23:32:52 Found 1 DVD±RW/RAM! I 23:32:58 Operation Started! I 23:32:58 Source File Sectors: 4,084,528 (MODE1/2048) I 23:32:58 Source File Size: 8,365,113,344 bytes I 23:32:58 Source File Application Identifier: IMGBURN V2.3.2.0 - THE ULTIMATE IMAGE BURNER! I 23:32:58 Source File Implementation Identifier: ImgBurn I 23:32:58 Source File File System(s): ISO9660, UDF (1.02) I 23:32:58 Destination Device: [4:0:0] Optiarc DVD RW AD-7170S 1.82 (F (ATA) I 23:32:58 Destination Media Type: DVD+R DL (Disc ID: RICOHJPN-D01-67) (Speeds: 2.4x, 4x, 6x, 8x) I 23:32:58 Destination Media Sectors: 4,173,824 I 23:32:58 Write Mode: DVD I 23:32:58 Write Type: DAO I 23:32:58 Write Speed: 2.4x I 23:32:58 Link Size: Auto I 23:32:58 Test Mode: No I 23:32:58 BURN-Proof: Enabled I 23:32:58 Optimal L0 Data Zone Capacity: 2,042,272 I 23:32:58 Optimal L0 Data Zone Method: ECC Block Boundary I 23:33:29 Filling Buffer... (40 MB) I 23:33:30 Writing LeadIn... I 23:33:31 Writing Image... (LBA: 0 - 4084527) I 23:33:31 Writing Layer 0... (LBA: 0 - 2042271) W 23:46:41 Failed to Write Sectors 1242976 - 1243007 - Write Error W 23:46:41 Retrying (1 of 20)... W 23:46:42 Retry Failed - Write Error W 23:46:42 Retrying (2 of 20)... W 23:46:42 Retry Failed - Write Error W 23:46:42 Retrying (3 of 20)... W 23:46:42 Retry Failed - Write Error W 23:46:42 Retrying (4 of 20)... W 23:46:42 Retry Failed - Write Error W 23:46:42 Retrying (5 of 20)... W 23:46:42 Retry Failed - Write Error W 23:46:42 Retrying (6 of 20)... W 23:46:42 Retry Failed - Write Error W 23:46:42 Retrying (7 of 20)... W 23:46:42 Retry Failed - Write Error W 23:46:42 Retrying (8 of 20)... W 23:46:42 Retry Failed - Write Error W 23:46:42 Retrying (9 of 20)... W 23:46:42 Retry Failed - Write Error W 23:46:42 Retrying (10 of 20)... W 23:46:42 Retry Failed - Write Error W 23:46:42 Retrying (11 of 20)... W 23:46:42 Retry Failed - Write Error W 23:46:42 Retrying (12 of 20)... W 23:46:42 Retry Failed - Write Error W 23:46:42 Retrying (13 of 20)... W 23:46:42 Retry Failed - Write Error W 23:46:42 Retrying (14 of 20)... W 23:46:42 Retry Failed - Write Error W 23:46:42 Retrying (15 of 20)... W 23:46:42 Retry Failed - Write Error W 23:46:42 Retrying (16 of 20)... W 23:46:42 Retry Failed - Write Error W 23:46:42 Retrying (17 of 20)... W 23:46:42 Retry Failed - Write Error W 23:46:42 Retrying (18 of 20)... W 23:46:42 Retry Failed - Write Error W 23:46:42 Retrying (19 of 20)... W 23:46:42 Retry Failed - Write Error W 23:46:42 Retrying (20 of 20)... W 23:46:42 Retry Failed - Write Error W 23:57:52 Retrying (21)... W 23:57:52 Retry Failed - Write Error W 23:57:53 Retrying (22)... W 23:57:53 Retry Failed - Write Error W 23:57:54 Retrying (23)... W 23:57:54 Retry Failed - Write Error W 23:57:55 Retrying (24)... W 23:57:55 Retry Failed - Write Error E 23:58:03 Failed to Write Sectors 1242976 - 1243007 - Write Error I 23:58:03 Synchronising Cache... I 23:58:04 Closing Track... E 23:58:09 Close Track Failed! - Reason: Write Error I 23:58:09 Closing Track (Last Attempt!)... E 23:58:09 Close Track Failed! - Reason: Write Error I 23:58:09 Finalising Disc... E 23:58:16 Finalise Disc Failed! - Reason: Session Fixation Error - Incomplete Track in Session I 23:58:16 Finalising Disc (Last Attempt!)... E 23:58:16 Finalise Disc Failed! - Reason: Session Fixation Error - Incomplete Track in Session E 23:58:16 Failed to Write Image! E 23:58:16 Operation Failed! - Duration: 00:25:18 I 23:58:16 Average Write Rate: 1,688 KB/s (1.2x) - Maximum Write Rate: 3,474 KB/s (2.5x) -- Yakor
The Fuji might work better depending on the media code. There are two DVD-9s from Fuji. One good and one mixed. You could run the burn thur a Nero Simulation burn and not waste a blank. Otherwise I am out of ideas. http://www.videohelp.com/dvdmedia?d...rder=Name&hits=50&search=Search+or+List+Media edit If it is the good Fuji that you have and it fails the sim, I will seek help for some AfterDawn Addict's.
56 delray, You were right. It's the media. How can it be, whom shall I blame now? TDK? Send them back the media? Or NEC and Sony (or my local shop) requiring a replace of DVD drive? I'd still like to come back to the original topic: DMA and ATAPI controller. As I said before, now my AD-7170S is on JMicron SATA/PATA controller in AHCI mode. I tried different combinations: without installing JMicron drivers (in this case CD-ROM was on ATAPI Channel 0, with DMA enabled) and with installing JMicron driver (after this, the DVD drive is recognized as an SCSI device, and DMA option disappears in ATAPI Channel properties window as well as the whole drive moves nowhere, i.e. it is no longer under ATAPI Channel 0) Many thanks for advises, -- Yakor
56delray, It did work!!. Media ID "RITEK D01". I checked it thoutoughly with DVDInfo - all perfect. If this was possible!! I wouldn't have wasted so many. Simulation cannot be performed on DVD+R media. Btw, simulation option is also available in ImgBurn, so Nero is kind of... useless? -- Yakor
I do not use Nero much so I do not know that about the sim. I'm old school. I still use Decrypter to burn. Good luck!
