Starview 6 working!!

where are you ireland or Uk ??

if you are in the Uk it dont work there

if you are in ireland only works on 6887

and you have to have your internet connected and go back over the posts for the set up instructions

 

ok will try again thanks.........

 

ahhh..............no joy..I give up
going to play ps3 MW2 to calm down!!!!!!!

 

ok thanks again i know I am doing something stupid......will try tomorrow

 

yes best thing is to start with a clear head and also patients

check what firmware you have on your box if you can get into to turn the emu on thats fine then just start as below

so start from scratch at the very start and go forward follow every step and it will work as long as you are in the correct area as above you must be in NTL area of Ireland 6887 symbol rate.

and will not work on chorus or in the UK

 

Just a few things to clear up.
ST*VU 6, Dreambox, & I think latest Kryptvu work on 6887 EIRE.
Do not use grooverider 1.04; 8989 password does not open on this F/ware.
Use version 1.02.
St*vu 6 is great value if it lasts 12 months
St*vu track record dictates it won't last, you'll be left up swanee with no paddle.
Best bet is Dream-sat box; unlimited servers; if one closes down, switch server.
Just be sure to pay short-term server rent.
Cable-servers very limited, if yours goes off-line you may not have alt. server.
Good bet is to set up your own cable-server line (it's illegal)
P.S.
TUT-TUT MICKAH
I thought only novices posts were edited, Unless you knowingly incurred mods. wrath
because you felt info. needed to be made public.
Thought only renegades like me pulled strokes like me.

E45
Your knowledge ok ST*VU 6 is blatantly abstract, that's not your form. Your posts are
usually bang on the money. Read CLAIR-B's tut, it's very good.
Have been at lot of funerals last 5 weeks, but should be stable by Sunday.

 

I will be around from 6am to 10am sat. morning
P.M. me & I will sort you out.

 

eamo that is clair B tut all i done was pasted it on here from the front page so defo not my work as for the firmware that is the latest available to hand and if that dont work that is not down to me but to the starview team they should do thier homework on the firmware they released it as a working new image all we can do here is pass on the info end of.Any MISTAKES ON IMAGES IS STARVIEWS BABY not the poster.... and as i have said before on here i dont own a box so i dont know if the image works or not.... personally i would not have another starview how long will it be till we are up at Starview...... 7 ...... 8

Starview 6 is the only working cable box in Ireland on 6887 NTL at the moment but that will be short lived when Krypt come on stream as for Dreambox i myself have not seen any mention of that box working on any cable.

Kryptview is the only working box in the Uk at the present time working 100% in all N3 areas there is no other working box in the Uk NOW at the present time

 

ok guys I was getting the Menu when I installed GROOVERIDER 1.01 but even the then stations werent tuning in. Then Installed GROOVERIDER 1.04 But now i am not even getting da Menu on the screen ............help...is it dead?

 

suckmykiss,recheck all your cables,make sure you are connected to your router.reload firmware 1.01,autoscan again,go into your network settings and check your ip settings on the box through the menu,you should see a serious of boxes filled out{ip address,mask,dns,etc}if these are full of zeros disconnect your broadband and switch of box at the back for 30 seconds,then reconnect.go back into your ip settings and select auto then at the very bottom choose select,wait for about 30 seconds these boxes should now be filled in.i dont think its dead.its something simple that your doing wrong.its just a matter of finding the error.so just check above,and remember to have the power on the box switched of when inserting the USB stick as this could kill the box when its on.i dont have the box myself just going on memory here,will check back later today.....

 

Hi Lads.
Can any member confirm that the sv6 is working on mmds I am on a ntl mmds signal,symbol rate 6887.I just need the info regarding the mmds as I know it will work on cable.

 

no not at the moment

 

rechecked all me cables still no joy gonna try in an hr. or so thanks in advance ...fingers crossed

 

suckmykis,any joy with that?????will check back tomorrow.

 

sorryyy had a few beers.....c ya 2morrowwwwwwwwwwwww...........hic

 

I think it should work Hooter.
Under ch. name if it says CONNECTED then internet connection is fine.
Then do auto-scan because mmds. chls are diff. frequencies to N*L cable.
Just make sure EMU is enabled i.e. installation 8989.
Don't use f/ware 1.04. Use version 1.02
If it says NOT CONNECTED under ch. name you need to check internet connections.
Try AUTO-CONNECT to set up B/B connection.

 

Where is this famous Version 1.02 the only files i can find that have been released are the

V 1.00
v 1.01
V 1.03
V 1.04

Never seen the V1.02 for that box ?

 

V1.00 works perfectly mate, just stick with that! I've had that on mine since I got it, no problems!

Peace

Dubfella