STARVIEW Dublin problem (after codes)

Posted By Fergus
if you have Missing channels you can try this.

I have seen a few posts about channels missing when doing a full scan.
Here's a little trick you can try that may help if you're having problems
finding any particular channels or are missing channels:
Try and determine the lowest transponder frequency that you can get a signal on.
Look at the frequencies you already have on the channels saved so far and choose the lowest.
Then in the installation menu select MANUAL SCAN and set that as the frequency.
Make sure you can see a signal and scroll down to Network scan and change to ENABLE with the Right arrow.
While still highlighted, click OK.
Scanning should then begin. It will say 1/1 to start with but should then jump up to 1/?? (the ?? being 2 digits).
Using this method my Starview indicated it scanned 56/56 transponder frequencies as opposed to 48 in Auto scan on one main provider.
I also gained a few extra channels.
The other transponders may have been picked up by scanning other providers.

 

Leggs here in Ballybrack area tryed switching off svb nothing helps.??Its gettin very close to goin out nearest window

 

I presume you have your codes in right, leggs. what does it say on the screen ?

 

After entering all new codes nothing changes Channels say bad signal or scrambled channel have checked codes serveral times.

 

did u make sure you stored them each time?( i have to ask this so we can narrow it down )

 

Yes stored them each time.I put in yhe oo keys only and stored them they worked for few days then only selected channels work now like movieas and news channels.

 

ok , by now u should have these codes on :
00 = 29 c5 32 fa 51 a6 50 02
01 = 19 cb 80 ae 18 aa 08 41
Make sure Emu is on . If it is already on , you will have to rescan the channels in again
Make sure you use n*l as the provider !

 

Do iput in both sets of codes and store each after entering them in ?
I orignally only entered the 01 codes and it worked for a few days.The emu is on and can you give me instructions on how to rescan channels in again very new at all this techno stuff.Only just mastered the micro wave!!!!!

 

Lol. Yes you have to store any codes you put in ! It seems you are only missing one or 2 codes as you can receive some channels, Go in and check your 00 codes and store then check 01 codes and store exit out untill your back at tv screen and wait for a minute, it should say updating !

 

Entered each code 00 first and stored then 01 and code and stored but nothing has changed still says bad channel or scrambled.Nothing came up on screen

 

ok , you will have to do a rescan:
here;s how : from a previous post of mine .
1. plug box in and press Menu on
remote, installation, choose your cable provider(n*l),
then move don to automatic scan and press ok.

2. Once all channels have been found press exit back to TV screen.

3. Now press menu, parental control, press ok.

4. Now press the info button then the numbers 2 0 0 4. Move down to Key Emu and change option
to on.
Press ok , then exit back to TV Screen.

5. Go to scrambled channel and wait for it to unscramble the channels

6. then watch tv.

 

Tryed this and no joy just said found 36 channels but still have the same channels and nothing else.Any other ideas what the problem is.

 

Dunno if this will help , check your scart lead and the cable inputs into the SV and tv !

 

same for me, tnx anyway for the clues. hope we'll find a way to get back all the channels.

 

scarts and cables should be ok cause you have found some channels.
iF you are only getting some channels it normally means that you have a wrong code or two ! If you go back and view the codes on your box are they showing the right codes before you try change them ?

 

also try this :
go into hidden menu (menu, parrental contol, press INFO 2 0 0 4) & press default keys.

Then exit back to station & keys should update.!
If you are still missing channels i recommend reflashing the box , put v4.00e on it. ( for genuine boxes only not clones)
I have posted step by step instructions how to do this on page 1 of this thread !

 

Hi there, I have a few starview boxes with the v4 software loaded on to it thanks to this forums help and especially to mgryan. So just a quick question will I ever need to put in codes as I have not done so yet and my svb is about 3 weeks old. It seems to update itself. Thanks for your help in advance.

 

unless n** block it somehow don't know how. your box should auto update

 

your box should update