The Box Super (SV3) 301108 Fix.

can you press menu ... then system info and tell us what it says then?

 

Yes i pressed system info and it says SW Version :7.10
HW Version : 1770x-1.0-CS100-SID
if that is any help,
cheers.

 

Malci - I have downloaded the GT Rom file. (30/11/08)

I have followed the instructions on the link on "Updating Firmware for sv 1, 2, 3

However I get to the point where it says:

"Make sure App file only is selected, then click b1n File & browse to the firmw@re where you downloaded it to on your PC".

My bin file is greyed out and do i have to select "channel data file" instead? and if im browsing do i then relselect the GT Rom loader file ?

please explain mate

regards
Sniper200

 

Yes i pressed system info and it says SW Version :7.10
HW Version : 1770x-1.0-CS100-SID
if that is any help,
cheers.

 

What are you using to flash because the Starview 3 The Box Super is a Unified Firmware and Loader and you do not have to browse for a bin file, just press download on the GTRom v8.02e in top right corner - and yes App Files Only should be checked.


EDIT Do not check the Data File Box, ignore that, if you have it connected properly then it should go right away.

 

Malci that what i was doing intitially however the tut states that line that confused me?

I have so far connected to the box 3 and clicked app file only then clicked download button on the bottom left on the file it is now downloading to the sv3.

I have done this before however once I have put the sofyware on the sv3 and plug it up what steps do i nee to get it working as i have tried previous methods and to no avail?

when i auto scan it shows DVB-C (only)28 channels to scan as the info but when it goes to find the channels every single one fails and i have no picture at all not even normal 1-5 channels

 

can any of you good people out there upload a tsop bin file for ex1000sl help need badlt

 

hi guys I have just flashed the box super with the new firmware. But now all the box says when I go onto say sly1 is no signal??? I have checked all the cables and I have free to air channels!!! Any ideas???

 

Are you sure the coaxial is in "cable input" at the back of the b0x?

EDIT - Are you using a splitter?

 

i had to switch box off from the back and scan again and let it update
then i was sorted m8

 

Yeah the cables are in or I would not get the free to air channels. I will try the re scan hang on.........cheers

 

EDIT.

 

Neolyf when i scan for channels I get non all fail! I am using a splitter does that effect it?

 

cheers folks all sorted did the re scan updated a couple of times and hey presto all working........all i need now is the firmware for my box the sv2 (which i personally think is a better version) Seriously thought thanks alot I appreciate it your help!

 

Yes a splitter would affect the scan,remove it & scan, also make sure the coaxial is secuely in "cable input" on the b0x.

 

take the splitter off and try that mate

 

Glad you`re sorted.

 

anyone point me in right direction for tsop bin file for ex1000sl please

 

I had it sussed all along, it its just the connection on the back of the coxial is loose, it stops and goes any one know when the SV1 fix is coming out also would it be the same to update, as sv3?

regards

sniper200

Thanks every one for your hwlp really apprieate it

 

Hi

I have been trying to flash the new file, but getting error. I have original box. I open the file and click on download but then get the error message flash update failed. I am using the following cable, please let me know if this can be used:
http://www.maplin.co.uk/Module.aspx?ModuleNo=97737&DOY=1m11

I did a factory reset, then put the box on standby and then tried flashing, but got the error message. Will appreciate help.