how to switch the emu on

Hi I have a thebox pvr and just downloaded the new software dec 2008 can someone tell me how to put the emu on as was told this could be why im not getting the $ channels, when i press i then 2007 in parental control i can only go to nagravision I II or auto update

 

try this courtesy of sc0ucer-Go to parental control in receiver menu

press ( i or info button) + (2007)

key and emu buttons should now be visible
switch key emu to on position
go to scrambled channel and wait for update .

 

Hi i cant see key or emu buttons anywhere even when i press i 2007 on parental controls ?

 

I dont know much about the PVR boxes but this might make sense to you:

How to Upgrade PVR Firmware “
There are two methods to upgrade PVR Firmware as below.,
1. USB Download
2. Serial Download.
1. USB Download
1) Connect PC & STB with USB Cable
2) Main Menu-> Select ‘HDD Mode Change PVR’-> Press ‘0000’ on the RCU
( Showed ‘HDD Mode Change PC’ )
3) In PC
a) Showed new Local Disk on the PC ( ‘F:W’ or ‘E:W’ )
b) Copy new Firmware in the Local Disk.
4) Remove the USB Cable
5) Main Menu-> Select “HDD Mode Change PC”-> Press “0000” on the RCU
Once “HDD Mode Change PVR”, STB is automatically re-boot.
6) Main Menu-> ‘Select HDD Interface’ ->’Select Upgrade from HDD’
Select ‘new firmware -> Press ‘0000’ on the RCU
7) Automatically upgraded & re-boot.
2. Serial Download
1) Connect PC & STB with Serial Cable
2) Off & On with A/C Power on the rear panel.
3) Once display ‘ on ’ on the front panel,
Press ‘ OK->Exit->OK->Exit->OK->Exit ’ on the RCU.
4) Display ‘B-30 or B-31’ ( ready to download message ) on the front panel.
5) Access the ‘PVR Loader v3.36 Sep 7 2005.exe’ Select new Firmware
6) Download.
7) Automatically upgraded & re-boot

 

Hi thanks but i done that bit now im not getting the $ channels

 

as i said i am not familiar with that box but what happens if you press menu.. then input 1570 does that open the EMU?

 

nothing happens when i press menu then 1570 i can get into the cas system by pressing i 2007 in the parental control settings but no emu visible regards Richard

 

Richard will you have a look in here:
http://forums.afterdawn.com/thread_view.cfm/621354
as there is a good bit on PVR

 

sorry had to go out have a read through here courtesy of jbvideo-
http://forums.afterdawn.com/thread_view.cfm/705562

 

Hi ok downloaded the new software uk fix 081208 now my box says ver 3.105 8 dec 2008 is the version ok i downloaded it as app file only dont know if this makes a difference ?

 

Its fine if you are in the UK. Just make sure to enable k*ycode and menu lock after you have done a factory reset.

 

Scouser you are the man cheers mate I didnt turn k*y code on or menu lock god bless.

 

hi guys i have a replay box with a hard drive is there any new firmware updates yet i still have no channels and it is driving me bonkers i live in the north east of england thanx

 

Sorry nothing for the replay yet!!

 

i have the box pvr and have firmware e ver 4.506 15th oct 07 on it,i have been waiting for info on update(when and where to get it)but havent seen it yet.are people using one or are they using st**v**w 2 firmware as i thought the two were different?any ideas thanks for any advice joe

 

you will get it here:

http://www.4shared.com/account/file/75176629/1a775236/The_Box_PVR_081208_FIX.html

 

The firmware for the Starview 2 The Box and The Box PVR are not compatible, so never try to do anything like that, and there is a fix out for The Box PVR, check it out here and dowload and crack on with it. >>>>>>>>>

http://forums.afterdawn.com/thread_view.cfm/722659

 

cheers for info malci,much appreciated will sort update over weekend,thanks again joe

 

No bother joe, good luck