Eurovox New Software Released.Tested and Working.

I have UFL_MaxV_Kuro3_18_04_08.exe and
UFL_MaxV_Kuro3_28_04_08_T.exe on my laptop, I can't remember which one I ran.

I dont see Signal booster in Tv settings

Only V Mode,, TV Aspect Ratio, Video Output, Screen Mode, SPDIF Output, UHF Mode and UHF Channel

Am I missing something there, cheers the help by the way

 

right are you sure its a max v 2008 if so go into system info in config and post what it says .... and check here to make sure its not a clone http://forums.afterdawn.com/thread_view.cfm/659486

 

right have to head off in a few mins if your still there

 

He put the 28/04/08 firmware on, should have used the 18/04/08 version. It should stilll be OK, but to fix the TP problem he needs to do a factory reset and scan again.

 

Have not been home to try the factory reset. Does that mean I need to upload the 18/04/2008 version and start again?

 

Hi,
I think I am close to being able to flash my eurovox max blue clone (black box with silver panel)

I have the following:
1. Null Cable
2. EVMAX_BLUE_160408_CORE_140207

All I'm missing is the .exe file

Should I use Euromaxloader.exe or some other?

 

Hi Guys,

I have yet to download the latest firmware to the eurovox max v 2008. just noticed that there are 2 versions of kuro one from 18.04.08 and one from the 28.04.08. Which one shud i use? cheers

 

If you are NOT having any signal problems, then use the 18/04/08 it is fine - the 28/04.08 is mainly to address the 8 per cent signal problem, see scOuser's post above and the post a little higher.

 

Just try the factory reset first.

 

Yes for the clone use the loader, although you should have this in the RAR file. There is also a readme with it. If you need the whole pack you will find it in Eamos FTA Library.

 

Afraid not or it must be elsewhere. The dummy guide for updating eurovox clones is missing.
I unzipped EVMAX_BLUE_160408_CORE_140207.rar and the only file is EVMAX_BLUE_160408_CORE_140207.
I'm glad I asked the question though otherwise I'd have use the Kuro .exe

 

Sorry you are correct I mixed it up with the Black one. Just use Dnupman, you will find this in Eamos also in the Eurovox software folder. Before flashing upload a CDF from your box to PC using Dnupman. You will need this to download back to your EV after flash.

Now using Dnupman and the bin file, flash the EV. Then do a factory reset and download CDF back on. Put it on Sly Sports to update.

Note I only recommend using Dnupman for clone boxes.

 

Hi, I have the Eurovox MAX 5 Black box.
When I try to load the latest firmware for the Max 5 Black box I get the following message: "Firmware is not fit for your receiver" I have tried everything since my box stopped working in April and I think now that the problem is that I origionally used dnupman software to Flash the box. Can you advise?

 

Looks like you are using the wrong firmware. Are you using the latest for a Max V, if so it looks like you in fact have a blue or red version.

 

Hi all, somehow managed to voluteer to update a mates box but have only experience of St*rview, never done a eur*vox. I've looked through previous posts and am satisified that this box is a Genuine Eur*vox. It's black in colour, and has Euro-Vox Max on the front panel. Could someone point me in the direction of which firmware I need.


Ta in advance.

 

You will find everything you need in Eamo's FTA Library at the bottom of my post, but on second thoughts maybe you would be better off here, everything and how to >>>>>>>>>>>

http://forums.afterdawn.com/thread_view.cfm/653745

Use the Kuro firmware dated 18.04.08.

 

The box is not a Max v, but a black Euro-Vox Max. I can't see which firmware is for me, sorry

 

I should say that I followed the mentioned steps amd got an error message, "Not suitable for your reciever"

 

Starting at the rear right hand corner count the number of slots the tuner is visible for, if it is 8 slots it's a real Red or Black box, (if it covers 12 slots you have either a real Blue box or a clone) that will need further investigation. If you use the wrong firmware on a real box it will tell you that it is wrong, my guess is you probably have a black if it is encased all black, if it is grey could be RED box.

 

Just seen your post, check my last post, looks like a Red?