How to: Update Eurovox Max V with Kuro 18.04.08 (R.I.P 28/11/2008)

Keep going! all the best.

 

same happend to me, went ahead and all works great

 

cagerager

Have you tryed the new firmware 28/04/08 which helps people with the 8% signal problem, It may help you, Other than that providing your feed is ok I wouldnt know of any other fix, Others on hre may but id give this a try.
http://www.mediafire.com/?hsmji5wjpas

 

hi guys/girls im goin to try and download the software for the eurobox 2008...how do i no if its a red .blue or black box?????and what softwer do i use ?? can u help as i dont no really what im doin lol

 

Try describing the box to us,

Is it all black with silver buttons or is it black with a silver face,

Im off to bed but someone im sure by the morning will help you out if not I will try lol.

Make sure you do not have a clone,
look here
http://www.irelandeurovox.com/eurovoxclones.htm

does it look like no 1

If its this download this http://www.mediafire.com/?xynenwxvyjy/ and follow SG8s instructions on pg 1.

or like this,no 2

 

lol soory ppl...its the black with silver buttons(top pic)

 

No problem but look up again. Its all there.

 

im sure m8 it is but as im very very new to this i dont no where to look.........i have looked but avin no look as where to go now....but thks 4 replyin anyway

 

Hi again,
Continued on as you advised. Made it to step 11 without a problem. However it is now stuck at 8% Quality on the full power scan. Any suggestions??

 

iceman66:

Seriously!

Download this click on the writing at the side of this, http://www.mediafire.com/?xynenwxvyjy/

Then follow the instructions as SG8 has kindly added on pg 1 of this thread by clicking on this blue writing at the side or maybe underneath this, http://forums.afterdawn.com/thread_view.cfm/653745#3963550

I hope this helps you but at the min im off to bed and Im going this time lol , God damn this is addictive! Hope this helps good night!

 

drg1

Look here courtesy of sc0user,
http://forums.afterdawn.com/thread_view.cfm/659806

it should cure your problem.
night night!

 

Hi.

Sorry if this turns into a long post but I want to be as clear as possible.

I have the "eurovox max v 2008" box. Im with n*l in dublin.

I downloaded the file in the opening post of this thread and followed the instructions.

It didnt work. I then tried it again for the different symbol rates. This didnt work either. (I noticed that the subsequent times I tried to update the firmware it went through the steps slightly differently. The first time it power scanned by itself but there was a promt telling me to press ok which I did and then it did the power scan differently and this way in all subsequent attempts I made.)

So what happens anyway is I plug in my laptop, run the UFl, follow the steps on the config menue but afterwards I have no channels.

There is a blank table with a progress bar underneath stuck to 8% and an option to do the powerscan again (which wont actually do anything).

 

Easily fixed - Go to http://eko.4shared.com and go to "Eurovox", "Firmware" and download "28_04_08T" (or something to that effect) and flash as normal. This is a fix for precisely your problem. Good luck!

 

8877543

Look up 1 post above yours! the link is there to the download!

 

does anybody know how i manually put the codes in a eurovox max v

 

press menu languge selection key in 1968 1969 input codes

 

sorry wasnt looking while typing 1968 1968

 

Will the firmware work on this box? this is the one I got

http://img.diytrade.com/cdimg/35278.../Digital_Cable_Receiver_Euro-vox_max_2007.jpg

 

no you either have a blue red or clone blue=12 notches from the rf in, red=8notches take a look in here to see if you have a clone and then we'll get your proper firmware http://www.freewebs.com/euroclone/

 

more likely red if its a max 2007 like the link says blue boxes are usually 2006